Bosch ultraclarity pro User manual

en-us
20
Ice and water dispenser
The following may be dispensed as necessary:
■cooled water
■crushed ice
■ice cubes
When switching on the appliance, note the
following
The ice and water dispenser only works when the
appliance is connected to the water supply.
After the appliance has been switched on, it will take
24 hours before the first batch of ice cubes are ready.
When the appliance is connected, air bubbles will still
be in the lines.
Extract the drinking water and discard until water can
be dispensed without bubbles. Draw drinking water for
at least 5 minutes and pour away.
When using the ice maker for the first time, discard the
first 30 to 40 ice cubes. Do not use ice cubes for
hygienic reasons.
Operating the ice maker
Once the freezer compartment has reached its freezing
temperature, water flows into the ice maker and freezes
into ice cubes. The ice cubes are automatically
discharged into the ice cube container when they are
ready.
After the appliance is first switched on, it takes roughly
24 hours for the first portion of ice cubes to be
produced.
The sides of the ice cubes may occasionally stick
together. They usually break away from each other as
they move to the dispenser opening.
Ice making switches off automatically when the ice
cube container is full.
The ice maker can make approximately 140 ice cubes
within 24 hours when ice cubes are discharged several
times during the day.
As the ice cubes are being made, the sound of the
buzzing water valve, the water flowing into the ice
storage bin and the falling ice cubes can be heard.
Drinking water quality
All materials used in the water dispenser are odorless
and tasteless.
If the water has an aftertaste, this may be caused by:
■Mineral and chlorine content in the drinking water
■Materials from which the domestic water line or
connection line are made
■Freshness of the drinking water. If water has not
been dispensed for an extended period of time, the
water may have a ”stale” taste. In this case,
dispense approx. 15 glasses of water and discard.
Note:
Rinse the water system that is connected to the water
inlet if no water has been dispensed in the last five
days.
The taste and smell of the water can be improved by
installing the included filter cartridge at the water intake
point.
We recommend that you regularly draw off a certain
amount of water from the water dispenser and do not
switch the appliance off. This will maintain the best
water quality.
Dispensing water
1. Press the "Water" button. The display panel shows
the "Water" symbol.
:WARNING
Risk of injury from broken glass!
Never use fragile glassware to catch ice when
dispensed.
:WARNING
Risk of injury from rotating crusher blades!
Never reach into the ice cube dispenser opening.
NOTICE
Risk of damage to the appliance!
Do not place bottles or food in the ice cube container
in order to cool them quickly. The ice maker may
become blocked and damaged.
:CAUTION
The water filter included with the appliance only
filters out particles from the supplied water and
does not filter out bacteria or microbes.

en-us
21
2. Press a glass or container against the dispenser
lever until the glass is filled with the desired amount
of water.
Note:
The water from the water dispenser is cooled to a
pleasant temperature for drinking. If you prefer the
water to be colder, dispense some ice cubes into the
glass before drawing the water.
Dispensing ice
Only hold the container against the dispenser lever until
the container is half full of ice. Otherwise, the ice in the
ice-cube dispenser spout may cause the container to
overflow or block the ice cube dispenser spout.
If crushed ice was dispensed before dispensing ice
cubes, there may still be some crushed ice in the
dispenser spout. It will come out together with the first
few ice cubes.
1. Press the "Ice cubes/Crushed ice" button until the
display shows the "Ice cubes" or "Crushed ice"
symbol.
2. Press a suitable glass or container against the
dispenser lever until it is filled with the desired
amount of ice.
Switching off the ice-maker
Note:
It is imperative to turn off the water supply to the
appliance several hours before switching off the
ice-maker.
If you do not expect to be using the ice-maker for
longer than 1 week (e.g. when going on holiday), the
ice-maker should be temporarily switched off to stop
the ice cubes freezing together.
1. Press and hold the "Ice cubes/Crushed ice" button
for 3 seconds.
In the display, the symbols "Ice cubes", "Crushed ice"
and "Lock" flash for approx. 3 seconds.
Then the water dispensing is switched on and the
symbol "Water" lights up.
Note:
When the "Ice cubes/Crushed ice" button is pressed,
when the ice-maker is switched off, an alarm sounds
and the symbols "Ice cubes" , "Crushed ice" and "Lock"
flash for approx. 3 seconds.

en-us
22
2. Pull out the ice-cube container.
3. Empty the ice-cube container and clean it.
4. Push the ice-cube container all the way back on the
runners until it snaps into place.
Switching on the ice-maker
Press and hold the "Ice cubes/Crushed ice" button for
3 seconds.
An alarm sounds as soon as the ice-maker is switched
on.
Water filter
Filter cartridges for the water filter can be obtained from
Customer Support.
Important notes on the water filter
■After use, the water system is slightly under
pressure. Take care when removing the filter
cartridge.
■If the appliance has not been used for the last
5 days or the water has an unpleasant taste or smell,
flush the water system through. To do so, draw water
from the dispenser continuously for 5 minutes. If the
unpleasant taste or smell persists, change the filter
cartridge.
Changing the filter cartridge
After six months has elapsed, the water filter symbol
starts flashing as a prompt to change the filter cartridge
(see section "Water filter symbol").
The filter cartridge must be replaced after six months at
the latest.
1. Caution! Unplug the appliance from the mains or
switch off the circuit-breaker.
2. Turn off the water supply to the appliance.
3. Press the button and remove the lid.
Note:
Take care when removing the filter cartridge.
The water system is slightly under pressure after use.
4. Carefully turn the filter cartridge 90° counter-
clockwise and pull it out.
5. Take the new filter cartridge out of its packaging.
6. Insert the new filter cartridge and carefully turn it
90° clockwise as far as the stop.
:WARNING
In localities where the water quality is not ideal or
not known, do not use the appliance without
suitable means of disinfection on the inlet and outlet
side of the filter.
:CAUTION
■After fitting a new filter cartridge, always throw away
the first 24 hours' worth of ice produced after
switching on the ice-maker.
■If the ice has not been used for an extended period,
throw away all the ice cubes in the ice-cube
container as well as the ice produced over the next
24 hours.
■If the appliance has not been used or no ice has
actually been dispensed for several weeks or
months, or if the ice cubes have an unpleasant
taste or smell, change the filter cartridge.
■Air trapped in the system can cause water to spurt
out and eject the filter cartridge. Take care when
removing it.
■The filter cartridge must be replaced at least every
6 months.

en-us
23
Note:
The filter cartridge must be tightened by hand so that
no leaks are created and that the appliance is correctly
supplied with water.
7. Refit the lid and snap it into place.
8. Turn on the water supply to the appliance.
9. Switch on the appliance.
10.Dispense and dispose of water for five minutes via
the water dispenser.
11.Pour the water out of the old filter cartridge. The filter
cartridge can be disposed of together with the
normal household waste.
12.Press and hold the "Light/Filter" button for
3 seconds. That resets the water filter indicator. The
symbol will then stop flashing. The new filter has
now been activated.
Note:
The ice and water dispenser can also be used without
a water filter. In that case, fit the cover cap.
Cover caps can be obtained from customer service.
Performance Data Sheet
NSF System Trade name: WFS200MF & WFS210MF
NSF Replacement Cartridge No: WFC100MF (for WFS200MF) & WFC110MF (for WFS210MF)
This system has been tested according to NSF/ANSI 42, 53, 401 for reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than
or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42, 53, 401.
System tested and certified by NSF International against NSF/ANSI Standard 42, 53, 401
for the reduction of the claims listed below.
Substance Influent challenge
concentration
Average reduction Reduction
requirement
Max. permissible
product water
concentration
Chlorine taste and
odor 2.0 mg/L ± 10 % 97.2 % ≥50 % N/A
Chloramine 3.0 mg/L ± 10 % 97.2 % N/A 0.5 mg/L
Particulate, Class I
particles ≥0.5 to <1 μm
at least 10,000
particles/mL >99.9 % 85 % N/A
Atrazine 0.009 mg/L ± 10 % >94.4 % N/A 0.003 mg/L

en-us
24
Tested using a flow rate of 0.55 gpm (2.0 L/min), pH of 7.5 ± 0.5, pressure of 60 psig, and temperature of 68 ± 5 °F.
NOTE : The testing was performed under standard laboratory conditions, actual performance may vary.
Operation conditions
Warning: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain
filterable cyst.
Note:
■Adsorption media will not be regenerated and used.
■Systems must be installed and operated in accordance with manufacturer’s recommended procedures and
guidelines. The system and installation shall comply with applicable state and local regulations. Install on cold water
line only.
■Flush 3 gallons through filter before use (flush approximately 5 minutes).
■To maintain proper filtration, replace the filter at least every 6 months.
Manufacturer: Microfilter co.,Ltd.
15-1, GWINONG3-GIL, DEOKSAN-MYEON, JINCHEON-GUN, CHUNG-BUK 27856, KOREA
Phone: [phone]
Benzene 0.015 mg/L ± 10 % >96.8 % N/A 0.005 mg/L
Carbofuran 0.08 mg/L ± 10 % >98.8 % N/A 0.04 mg/L
p-Dichlorobenzene 0.225 mg/L ± 10 % >99.8 % N/A 0.075 mg/L
Lead pH = 6.5 0.15 mg/L ± 10 % >98.8 % N/A 0.010 mg/L
Lead pH = 8.5 0.15 mg/L ± 10 % 97.9 % N/A 0.010 mg/L
Mercury pH = 6.5 0.006 mg/L ± 10 % >96.5 % N/A 0.002 mg/L
Mercury pH = 8.5 0.006 mg/L ± 10 % >96.6 % N/A 0.002 mg/L
Turbidity 11 ± 1 NTU 99.1 % N/A 0.5 NTU
Ethylbenzene 2.1 mg/L ± 10 % >99.9 % N/A 0.7 mg/L
Toxaphene 0.015 mg/L ± 10 % N/A 0.003 mg/L
Asbestos
107to 108fibers/L;
fibers greater than
10 μm in length
>99 % 99 % N/A
Cyst minimum 50,000/L 99.99 % 99.95 % N/A
Meprobamate 400 ng/L ± 20 % >95.2 % N/A 60 ng/L
Atenolol 200 ng/L ± 20 % >95.6 % N/A 30 ng/L
Carbamazepine 1,400 ng/L ± 20 % >98.6 % N/A 200 ng/L
DEET 1,400 ng/L ± 20 % >98.7 % N/A 200 ng/L
Phenytoin 200 ng/L ± 20 % >94.4 % N/A 30 ng/L
Metolachlor 400 ng/L ± 20 % >98.7 % N/A 200 ng/L
Ibuprofen 400 ng/L ± 20 % >95.3 % N/A 60 ng/L
Trimethoprim 140 ng/L ± 20 % >96.7 % N/A 20 ng/L
Linuron 140 ng/L ± 20 % >96.6 % N/A 20 ng/L
Naproxen 140 ng/L ± 20 % >96.2 % N/A 20 ng/L
Estrone 140 ng/L ± 20 % >96.3 % N/A 20 ng/L
Bisphenol A 2,000 ng/L ± 20 % >99.0 % N/A 300 ng/L
Nonyl phenol 1,400 ng/L ± 20 % >96.3 % N/A 200 ng/L
Substance Influent challenge
concentration
Average reduction Reduction
requirement
Max. permissible
product water
concentration
Service flow rate 0.55 gpm (2 L/m)
Water pressure 30 psi - 120 psi (206 - 861 kPa)
Water temperature 35 °F - 100 °F (2 °C - 38 °C)
Function chemical/mechanical
Capacity WFS200MF 250 gallons (946 L), WFS210MF 150 gallons (567 L)