BoundaryTEC ShowerCoil 1530A User manual

IMPORTANT
Read this entire manual carefully before setup, operation or repair of this product.
Keep this manual available for future reference.
If you have questions about setup, operation, or repair, please call BoundaryTEC, LLC.
at 800.753.9943, or email at [e-mail]
Please take a minute to register your
product:
www.boundarytec.com/register.php
Scan this code to play
instructional video
or enter the address
below in a web
browser:
http://
youtu.be/FV5OJg3L02Q
U.S. Pat. No. 9,303,898
INSTRUCTIONAL
VIDEO LINK
ShowerCoil Instruction Manual
Models 1530A/1532
2
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Safety
Warning Indicates a hazardous situation which, if not
avoided, could result in death or serious
injury.
For outdoor use only.
Operate only in well ventilated areas clear of flammable materials.
Do not leave heating system unattended while in use.
Observe all applicable federal, state and local regulations when constructing a
camp fire.
Keep children and pets clear of heating system when operating.
Using a stove to heat this product can produce carbon monoxide which has no
odor.
Use of this product in an enclosed space can result in death.
Do not use this product in an enclosed space such as a camper, tent, car or
home.
Always defer to and follow stove manufacturer’s instructions and safety
requirements when using a stove in conjunction with this product.
Heating coil and system parts become hot during use
Use care when placing or removing heating coil from heat. Do not directly
touch heated parts.
Allow heating coil and sheath to cool before handling.
Do not operate if heating coil is kinked or damaged. Doing so can cause
excessively high water temperatures or burst heating coil.

3
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
DO NOT HEAT COIL AT ANY TIME WITHOUT WATER FLOWING THROUGH
SYSTEM. Doing so can damage or melt the heating coil, prevent the system
from priming, produce hot steam, and cause a risk of injury including burns.
Remove coil from heat before water has completely drained from water supply
bag. Failure to do so can damage the product, produce hot steam, and cause a
risk of injury including burns.
Misuse or abnormal operating conditions can produce hot steam.
Steam can cause damage to water bags and risk of injury including burns.
Temperatures exceeding 212°F (100 C) are possible.
In the event that steam is produced during operation (indicated by a gurgling
or hissing sound similar to a coffee maker brewing) First, immediately remove
coil from heat without directly touching heated parts, then follow the
troubleshooting recommendations in this manual.
Always elevate the water supply bag outlet 30-36 inches (76-91 cm) above the
water collection bag during heating process. Failure to do so can produce
excessive water temperatures, equipment damage, and risk of injury including
burns.
Heat only clean water with this product – Water containing debris can clog
thermostat, block flow and cause hot steam and a risk of injury including burns
and equipment damage.
Do not use mouth to siphon or purge water through the heating system.
Doing so with a hot system can cause severe burns of the mouth and throat.
Do not leave heating system unattended while in use.
Test water temperature before showering.
Heated water not for consumption.
System not designed to heat water above 115°F (46 C).
Do not modify or alter the product in any way.
Use this product only as instructed in this manual.
4
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Contents
SAFETY ................................................................................................................................... 2
SPECIFICATIONS ...................................................................................................................... 4
PRODUCT OVERVIEW .............................................................................................................. 5
DESCRIPTION OF CONTENTS ................................................................................................... 6
BEFORE YOU BEGIN ................................................................................................................ 7
OPERATION – WATER HEATING .............................................................................................. 8
Heating Recommendations .................................................................................. 12
OPERATION - 15L UNIVERSAL BAG ........................................................................................ 13
Instructions – as Shower ...................................................................................... 13
Instructions – for Storing and Dispensing Drinking Water ..................................... 13
Instructions – as Dry Bag ...................................................................................... 13
TIPS AND INFORMATION ...................................................................................................... 14
STORAGE .............................................................................................................................. 15
MAINTENANCE ..................................................................................................................... 15
TROUBLESHOOTING.............................................................................................................. 17
SERVICE PARTS ..................................................................................................................... 19
ONE YEAR LIMITED WARRANTY ............................................................................................ 20
Specifications
Model 1530A Model 1532
Weights
Heating Coil Assembly
Water Bag (ea.)
Dry Weight (System)
15 oz /425 g
7.0 oz / 200 g
30 oz / 850 g
15 oz /425 g
n/a
16.6 oz / 470 g
Dimensions
Heating Coil Assembly (packed)
Inlet Tube Length
Outlet Tube Length
8” Dia. x 2”H / 20 cm Dia. x 5 cm H
76” / 1.9 m
32” / 0.8 m
Shower Capacity 4 gallons / 15 liters n/a
Temperature Selector Range 85°F
–
115°F / 30 C
–
46 C
Shower Run Time (4 gal.) 8-9 min. n/a
For Use with Stove Type Single Burner Backpacking Stove
10,000-15,000 BTUH Output
Adapter Kit
Fits third party solar shower
port outer diameter
n/a 0.43-0.50”
(11-12.7mm)

5
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Product Overview
You have just purchased one of the most effective portable water
heater and shower systems available. ShowerCoilTM Portable Water
Heater and Shower enables you to enjoy a hot shower virtually
anywhere in just 2 basic steps.
1 Heat Water
The ShowerCoil system heats water
using either a camp fire or a stove.
Water can be heated to an accurate
temperature typically in about 10-15
minutes.
Gravity causes water to flow from an
elevated cold water supply bag,
through a heating coil, and into the
lower heated water collection bag.
A thermostatic valve regulates the flow
rate of the water to deliver an accurate
heated water temperature for use in
Step 2.
2 Use like a solar shower
After the heating process is complete, a gravity fed
shower or other cleanup function can be
implemented by attaching the shower head and
suspending the shower bag overhead from a tree
limb or other structure.
Remember to dispose of wash (gray) water responsibly. Wash yourself or
dishes at least 150 feet away from streams or lakes to avoid soap run-off into
a natural water source. Check with the appropriate park district or
campground to learn about their specific gray water disposal policy.
6
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Description of Contents
Your new shower system should contain the following items:
Includes:
1530A 1532
Item Description Qty Qty
A Heating Coil Assembly 1 1
B 15L Universal Bag 2 -
C Shower Head Assembly with Pinch Valve 1 1
D Heat Deflector - Improves heating efficiency when
heating with a stove. 1 1
E Y-Stand - Embeds into ground for tube support when
heating with a stove.
1 set
(2 pcs)
1 set
(2 pcs)
F Drawstring Storage Bag 1 1
G Adapter kit (for connecting heating coil to third party
solar showers) - 1 pair
10x10” Poly Bag
–
(not shown)
Do not discard this bag.
(This poly bag can be used to pre-wrap the coil before
storing in drawstring bag. The exterior of the coil may
become dirty with creosote when heated with a camp
fire.)
1 1
Manual 1 1
Instructional video web link (see front of manual)
A
B
C
E
D F
G

7
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Before you begin
Model 1532 only - Preparing third party solar showers for use with system.
1. Remove existing shower hoses from outlet port of third party solar showers if present.
2. Slide supplied adapter connectors onto outlet ports.
a. Outlet port outer diameter of solar shower must be between 0.43-0.50 inches (11-12.7mm).
3. Before filling cold water supply bag, temporarily insert supplied shower head into adapter connector
to plug outlet.
4. Close pinch valve
Water containers that have shutoff valves at the outlet port are not
advised for use with the ShowerCoil system. However, if they are used,
extra care must be taken to ensure each valve is fully open during the
heating process to maintain unrestricted water flow. Failure to do so can
damage or melt the heating coil due to absent or inadequate water flow
and produce steam or overheated water causing a risk of injury including
burns.
8
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Operation – Water Heating
5. Fill Supply Water Bag.
a. Fill one bag with clean water.
Note: If collecting water from a lake or river, hold the bag as shown below
and horizontally scoop undisturbed water a few inches below the
surface. This technique allows the cleanest water to be collected.
b. Fold the top flap toward the front translucent side of the bag and
press out some of the trapped air.
c. Roll over the top edge of the bag 4x towards the front
translucent side of the bag while ensuring that the front ply of
the bag stays in contact with the back ply and does not slide
apart or wrinkle.
d. Bend the ends of the buckles back around toward the fabric
side of the bag and snap.
6. Elevate Supply Bag
a. Suspend the filled supply bag as
shown so its drain port is 30-36
inches above the empty bag on the
ground.
b. Suggested options for suspending bag:
i. Suspend from tree limb if
available.
ii. Field constructed tripod
Lash 3 sticks together with a
cord as shown. Sticks should
be about 5 feet in length.
iii. BoundaryTEC Aluminum Tripod Accessory
Stands
PN: 1540 or 1542.
7. Uncoil heating assembly and
straighten out rubber tubing,
ensuring there are no kinks.
8. Flatten and force any air out of the empty bag before closing up. Evacuating the air will ensure there
is enough room for the all of the flowing water during the heating process.
a. Ensure the lower empty bag is equal to or larger in size than the supply bag if using 3rd party
shower bags.

9
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
9. Drain heating coil of any residual water left inside from prior use.
10. Prepare heat source. (Perform step a if heating with a fire, and b if using a stove)
(See heating recommendations section, pg. 12)
a. Camp Fire - Prepare and start a camp fire with dry wood in a contained
fire ring or pit.
Observe all applicable federal, state and local regulations when
constructing a fire.
b. Stove – Light stove.
c. DO NOT PLACE COIL ON CAMP FIRE OR STOVE UNTIL INSTRUCTED.
11. Interconnect the heating system
a. Remove the black purge valve from the short rubber
tube at the base of the bag on the ground and insert
the thermostat port into the tube.
b. Set desired temperature on the thermostat. Use
setting #4 (100F) if unsure. (see “Tips’ section for
recommended temperatures)
c. Connect the blue supply tube to the short tube at
the base of the elevated bag. To prevent water from
spilling, pinch the short tube attached to the bag
while removing the purge valve and connect the
supply tube.
12. Verify that air bubbles have purged through the
tubing and water has started to flow into empty bag.
Failure to follow steps 2-4 can cause inadequate water flow during heating and produce
steam or overheated water.
DO NOT HEAT COIL AT ANY TIME WITHOUT WATER FLOWING
THROUGH SYSTEM. Doing so can damage or melt the heating coil
and cause a risk of injury including burns.
10
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
13. Place coil over heat using a stick.
a. Camp Fire (See heating recommendations section, pg. 12)
i. The coil should be in a concave down position to help the coil
balance properly on top of the fire wood.
ii. Do not use the heat deflector with a camp fire.
iii. Shield the bag on the ground to prevent damage from potential “popping” embers.
b. Stove (Single Burner Backpacking Stove 10,000-15,000 BTUH Output)
(See heating recommendations section, pg. 12)
i. The coil should be centered on the stove in a concave up position
with the heat defector in the center of the coil.
ii. Assemble the Y-Stand and push it into the ground to support the
end of the tube jacket.
Important! Do not heat exposed rubber tubing.
Note It is normal for water drops to condense and drip from the coil when heating.
Important! Do not directly use or test water flowing from the thermostat valve during the
heating process. The thermostat’s normal temperature oscillations prevent
setting the temperature by “feel”. Always use a water collection bag to equalize
the water temperature and let the thermostat do its job.
Heating coil and system parts become hot during use. Use care when
placing or removing heating coil from heat. Do not directly touch
heated parts. Allow heating coil and sheath to cool before handling.

11
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Important! Do not leave system unattended while in use.
Misuse or abnormal operating conditions can produce hot steam.
Steam can cause damage to water bags and risk of injury including burns. Temperatures
exceeding 212° F (100 C) are possible.
In the event that steam is produced during operation (indicated by a gurgling or hissing
sound similar to a coffee maker brewing) First, immediately remove coil from heat
without directly touching heated parts, then follow the troubleshooting
recommendations in this manual.
14. REMOVE coil from the heat source using
a stick BEFORE water level reaches the
outlet port of supply bag.
Note: There will remain a small amount
of water in the bag below the outlet
port. The water will not completely
empty from the bag.
15. See - Shower Operation (pg. 13)
12
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Heating Recommendations
The ShowerCoil thermostat valve is very effective in controlling the heated water temperature across a
range of temperature and conditions. However, to ensure accurate water temperatures, follow the heating
recommendations below.
N/R Not Recommended
Important! Do not exceed maximum recommended heating intensity. Doing so can
produce water temperatures which exceed temperature setting.
Note
Normal heating times for a full bag of water will range from 10-18 minutes.
If actual times are outside of this range, recheck the heat intensities above
and refer to the Troubleshooting section of this manual.
Tip A fresh camp fire with flames passing over the coil will give the best heating
results.
Tip Insulate the lower (heated) water bag from the ground by placing it on a
towel or foam pad when the outside temperature is cool (<65°F / <18 C).

13
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Operation - 15L Universal Bag
Instructions – as Shower
1. After the heating process is finished and the heating coil has been
removed from the heat, remove the thermostat valve from the
heated water bag and insert the showerhead assembly into the
short tube attached to the bag.
2. To prevent water from spilling, pinch the short tube attached to
the bag while removing the thermostat valve and connect the
showerhead assembly.
3. Make sure the pinch valve is closed to prevent leakage.
4. Hang bag from a tree limb, BoundaryTEC Shower Tripod (1542),
or other structure. (see ‘Tips’ section for help with lifting the bag
overhead)
5. Use thumb and forefinger to control the pinch valve for on/off
and flow adjustment.
6. The sealed bags will slow down heat loss. See cool down times in
the ‘Tips’ section of this manual for recommended times in which
to use hot water before a detectable drop in temperature takes place.
7. Test water before showering.
Instructions – for Storing and Dispensing Drinking Water
WARNING! Follow safety instructions below to reduce the risk of gastrointestinal illness
which may be caused by consuming water contaminated with harmful microorganisms.
Sanitize potentially contaminated bags, tubing and parts before contact with drinking
water.
Clearly identify bags and tubing as “clean” or “dirty”.
Keep potentially contaminated tubes, parts, and water away from clean water to prevent
cross contamination.
Sanitizing Instructions
1. Mix a mild bleach solution in the bag by adding 2 teaspoons of unscented liquid household chlorine
bleach to 1/2 gallon of water. (10 ml bleach per 2 liters water)
2. Press out excess air, then roll down the top closure loosely (2x).
3. Grasping each end of the bag, tip bag back and forth a few times so that all inner areas of the bag,
tube, and nozzle are wetted. A small amount of solution should drip from the top end of the bag;
drain into sink (if indoors).
4. Open valve to allow solution to flow through tubing and parts.
5. Wait 30 seconds then drain solution.
6. Thoroughly rinse bag, tube, and parts with clean water.
7. Hang bag upside down to air dry or dry with a clean towel.
Instructions – as Dry Bag
1. Fill bag with gear.
2. Fold the top flap toward the front translucent side of the bag and press out
some of the trapped air.
14
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
3. Roll over the top edge of the bag 4x towards the front translucent side of the
bag while ensuring that the front ply of the bag stays in contact with
the back ply and does not slide apart or wrinkle
4. Bend the ends of the buckles back around toward the fabric side of the
bag and snap.
5. To Compress: (if desired) Unscrew purge valve 1 turn, compress bag to force
out excess air. Close purge valve.
* Properly sealed bag will float or can withstand full submersions up to 3 meters deep
for short intervals.
Tips and Information
• Suggested Water Temperature Setting
Air Temperature Recommended Water
Temperature Setting
60-65°F (15.6-8.3 C) #7 - 115°F (46.1 C)
65-70°F (18.3-21.1C) #6 – 110°F (43.3 C)
70-75°F (21.1-23.9 C) #5 – 105°F (40.6 C)
75-80°F (23.9-26.7 C) #4 – 100°F (37.8 C)
80-85°F (26.7-29.4 C) #3 – 95°F (35.0 C)
85-90°F (29.4-32.2 C) #2 – 90°F (32.2 C)
• Preheat Water in Sun
If you are able to plan in advance for a shower and have some time to at least partially heat the water
in the sun, this is a great way to save time and fuel later when you are ready to heat the water to
temperature with your stove or camp fire. Note: Remember to reduce the heat intensity according to
heating recommendations section, pg 12.
• Lifting Water Bag – Simplified Block and Tackle (see fig.)
A helpful method for lifting the water overhead is to construct a
simplified block and tackle. By using two carabiners and two lengths
of braided nylon cord, the bag filled with water becomes much
easier to lift. Tie one end of the first cord to one of the carabiners,
and then hang it over a tree limb that is 8-10 feet high. Tie the
second cord to the upper carabiner, loop it through the bottom
carabiner, and then back through the upper carabiner. Adjust the
height of the upper carabiner by pulling the first cord and then tie it
off. Attach the shower bag to the bottom carabiner. Pull on the free
end of the second cord and at the same time lift up on the water
bag. Tie off the second cord.
• Windy Conditions with Stove
Windy conditions can cause the heating efficiency of a stove to drop
significantly. For best heating performance, shield system from wind
in compliance with stove manufacturer’s operating instructions.
Note: These settings are suggestions.
You’ll develop a good feel for your
preferred temperatures after using the
system a few times.
For optimum comfort, the air temperature
should be at least 60°F for an open air
shower.
Always test water before showering.

15
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
• Water Temperature Cool down Chart
The sealed water bags do slow down heat loss, but of course the temperature will eventually drop
over time. The following chart will help give a general indication of how soon the heated water
should be used after heating to prevent excessive temperature drop.
Time to Drop 3°F (1.7 C)
°F °C 90F (32.2C) 95F (35 C) 100F (37.8 C) 105 (40.6 C) 110 (43.3 C) 115 (46.1 C)
50 10.0 27 min. 24 min. 22 min. 20 min. 18 min. 17 min.
60 15.6 37 min. 31 min. 27 min. 24 min. 22 min. 20 min.
70 21.1 57 min. 45 min. 37 min. 31 min. 27 min. 24 min.
80 26.7 2 hrs 78 min. 57 min. 45 min. 37 min. 31 min.
90 32.2 5 hrs 2 hrs 78 min. 57 min. 45 min.
Initial Water Temperature (4 gallons / 15 l)Air Temp
• Shower Mat
To keep your feet clean when showering, bring along a small piece of poly
tarp or plastic to stand on.
Storage
Heating Coil
1. After it has cooled off, hold up the heating coil assembly to drain any
residual water out of the tubes before storing.
2. Place heating coil into the poly bag before
wrapping up and storing in drawstring bag. This
will contain any creosote which may have
accumulated on the coil.
15 Liter Universal Bags
1. Sanitize and dry bags before or after long-term storage (see page 13
for instructions).
2. Store flat or roll as shown.
Maintenance
1. Heating Coil – Cleaning Creosote
If you use a camp fire to heat the coil, creosote (soot) can build up on the exterior of the heating
coil over time. This buildup will not cause any damage to the coil but can lower the efficiency of
the heating system.
If desired, a heavy duty household oven cleaner can be used periodically to remove this creosote
coating from the outside of the coils. Follow oven cleaner manufacturer’s directions.
Rinse thoroughly and allow to dry before storing or using.
Chart shows
approximate times in
which the temperature
of a full water bag
drops 3 °F (1.7 C).
16
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
2. Thermostat Inspection
The thermostat may be opened up periodically (yearly) to check for debris and verify function.
Important! Do not attempt to remove the set screw on the end of the thermostat
dial. This will cause the thermostat to lose its calibration, possibly
causing excessive water temperatures or hot steam during operation
posing a risk of injury including burns.
To check the thermostat:
a. Remove the (4) Phillips screws holding the thermostat case
together.
b. Before separating the case turn the case over with the dial
toward the ground. This will help prevent the small black
valve gate from falling out and getting lost.
c. Remove the small black valve gate and set aside.
d. Look over the inside of the housing:
i. Check for Debris: Remove any debris if found.
ii. Check Function:
1. Set thermostat dial to the center position
(#4).
2. Run hot tap water over the bimetal coil.
The formed end of the coil should rotate
outward to the edge of the housing.
3. Run cold tap water over the bimetal coil. The
end of the coil should rotate to the middle of
the housing and rest against the stop.
4. Replace thermostat assembly if function does
not match the above description.
iii. Check for Corrosion: Over time the inner bimetal
coil may show some white rust as well as some
localized areas of red rust. This is normal and will
not impact the thermostat accuracy. If excessive
red rust is seen (possibly after a several years of use), the thermostat should be
replaced to ensure its accuracy. See the ‘Service Parts’ section of this manual and
contact BoundaryTEC to order a replacement thermostat.
e. Assemble the thermostat in reverse order, making sure not to forget the small black valve
gate into the formed end of the bimetal coil. Torque (4) screws 4-6 in-lbs.

17
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Troubleshooting
Problem Possible Causes Solutions
Time required to
heat water was very
long and
temperature was
cooler than
expected.
(18+ minutes)
1. Heat intensity is too low given the initial
water temperature and the selected final
water temperature.
2. Windy conditions causing poor heating
efficiency with stove.
3. Heat deflector was not used when
heating with a stove.
1. Repeat heating.**
2. Repeat heating, shielding system from
wind according to stove manufacturer’s
operating instructions.**
3. Repeat heating, positing the heat
deflector in the center of the coil.**
**If reheating water, use a reduced heat
intensity according to the chart on pg 12 to
avoid temperature overshoot.
Heated water is
cooler than
expected.*
1. Thermostat temperature dial was not
set properly.
2. The elevated water bag was positioned
too high.
3. Faulty thermostat valve.
1. Set the preferred temperature on the
dial. Repeat heating.**
2. Elevate bag as shown on pg 8 and
connect system as shown on pg. 9. Repeat
heating.**
3. Inspect thermostat valve (see
maintenance section)
**If reheating water, use a reduced heat
intensity according to the chart on pg 12 to
avoid temperature overshoot.
Heated water is
warmer than
expected.*
1. Thermostat temperature dial was not
been set properly.
2. The elevated water bag was positioned
too low.
3. Heat intensity is too high given the initial
water temperature and the selected final
water temperature.
4. Faulty thermostat valve.
For an Immediate Solution #1 - 4 : Dilute
bag with cold water or allow water to cool
before using.
1. Set the preferred temperature on the
dial.
2. Elevate bag as shown on pg 8 and
connect system as shown on pg. 9.
3. Adjust heat intensity within
recommendations on heating chart. (see
pg. 12.)
4. Inspect thermostat valve (see
maintenance section)
(continued)
18
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Problem Possible Causes Solutions
Water does not
flow after
interconnecting
the heating
system.
1. Supply water bag is not elevated and
connected properly.
2. The rubber tubing is kinked.
3. Thermostat valve is clogged.
1. Elevate bag as shown on pg 8 and
connect system as shown on pg. 9.
2. Straighten tubing to remove kink.
3. Inspect thermostat valve (see
maintenance section)
In the event that steam is produced during operation
(indicated by a gurgling or hissing sound similar to a coffee maker)
First, immediately remove coil from heat without directly touching heated parts or tubing,
then follow troubleshooting recommendations below.
Steam is
produced while
heating coil.
1. Cold water bag is not elevated and
connected properly.
2. Heat was applied to the coil
before all air was purged and water
was flowing through system.
3. Coil was not removed from the
heat before the water level fell to
the outlet port of the elevated bag.
4. The rubber tubing is kinked
5. The system is air-locked. This may
occur if the coil is not properly
drained from a previous use.
6. Thermostat valve is clogged or
faulty.
1. Remove coil from heat. Elevate bag as shown
on pg 8 and connect system as shown on pg. 9.
Verify air has purged and water is flowing into
lower bag. Resume heating.
2. Remove coil from heat. Verify air has purged
and water is flowing into lower bag. Resume
heating.
3. Remove coil from heat. Allow to cool before
handling. (In the future, remember to remove
coil from heat before the water level of the
elevated bag falls to the outlet port.)
4. Remove coil from heat. Straighten rubber
tubing to remove kink. Verify air has purged
and water is flowing into lower bag. Resume
heating.
5. Remove coil from heat. Allow to cool before
handling. Disconnect heating coil assembly from
bags, properly drain coil and tubes. Reconnect.
Verify air has purged and water is flowing into
lower bag. Resume heating.
6. Remove coil from heat. Allow system to cool.
Inspect thermostat valve (see maintenance
section).

19
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Service Parts
Repairs to heating coil or thermostat calibration should be done only by BoundaryTEC or an authorized
service person.
The following replacement parts or subassemblies are available from BoundaryTEC. Please contact
BoundaryTEC for pricing.
Item Description Part Number
A Heating Coil Assembly (includes thermostat assembly) 1590
B 15L Universal Bag 1571
C Shower Head Assembly with Pinch Valve 1580
D Heat Deflector 1600
E Y Stand (set) 1610
F Drawstring Storage Bag 1630
G Thermostat Assembly 1620
H Adapter kit (includes 2 connectors) 1670
A
B
C
E
D F
G
H
20
DOC: 100-032E
Questions?
800.753.9943
support
@
boundarytec.com
www.boundarytec.com
© 2015 BoundaryTEC, LLC.
Warranty
One Year Limited Warranty
BoundaryTEC, LLC. (“BoundaryTEC”), to the original owner ("Owner"), warrants that for a period of
one year from the date of purchase, the enclosed product (“Product”) will be free from defects in
material and workmanship. BoundaryTEC, at its option, will repair or replace this Product or any
component of the Product found to be defective during the warranty period.
This warranty is valid for the original Owner from the date of initial retail purchase and is not
transferable. Warranty claims must be accompanied by the original sales receipt.
This warranty does not cover damage from normal wear and tear of parts. This warranty does not
cover damage resulting from misuse or modification of the Product, use contrary to the operating
instructions or failure to follow maintenance instructions, commercial for-profit or non-profit
instructional or rental applications, disassembly, repair or alteration by anyone other than
BoundaryTEC or an authorized service center.
BOUNDARYTEC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
CAUSED BY THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THE ABOVE WARRANTY.
This limited warranty gives Owner specific legal rights; Owner may have additional rights, which
may vary state to state.
How to Obtain Warranty Service:
For warranty service, contact BoundaryTEC by phone or email to obtain a return authorization
number and further instructions. Owner is responsible for costs associated with returning Product
to BoundaryTEC for warranty service. Where at its discretion, BoundaryTEC deems Product eligible
for warranty repair or replacement, BoundaryTEC will pay the shipping and handling associated
with returning repaired or replaced Product to Owner.
• Phone: [phone]
• Email: [email protected]
DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE.
If you have any questions about this warranty please contact BoundaryTEC.