Boyd PB4000 Dimensional drawing

1
PBM-001
Rev 2
Product Informaon Manual
PEDO Bench
Includes Models: PB4000 & PB4001
12900 44th Street North
Clearwater, Florida 33762
800-255-2693 * 727-561-9292
FAX: [phone] SALES
FAX: [phone] SERVICE
www.boydindustries.com
PB4000
PB4001

2
PBM-001
Rev 2
Table of Contents
Title Page
Table of Contents
Introducon
Applicaon of Product
Warranty Statement
Safety Precauons
About Your Product
Descripon of Product Line
General Product Informaon
Product Specicaons
Feature Operaon
Drawer Removal / Installaon and Adjustment
Unpacking and Installaon Procedure
Light Post Installaon (Oponal)
General Maintenance and Care
Cleaning Informaon
Infecon Control
Service Informaon
Authorized Representave (Europe Only)
1
2
3
4
5-8
9
10
11
12

3
PBM-001
Rev 2
Intended Use and Application of Product
This product is designed to allow dental procedures to be performed in a horizontal posion with an adjustable back rest and
head rest. The PEDO bench has built in storage for non-ammable items. The delivery system (PB4000 only) is located close to the
head of the bench (either le or right hand are available) to allow for easy access.
Warranty Statement
All Boyd manufactured products are warranted against defects in material or workmanship only. No other warranes are
expressed or implied. This warranty shall extend for three (3) years for parts and one (1) year for labor. The Boyd warranty only
covers products manufactured by Boyd. Products distributed, not manufactured, by Boyd carry the stated manufacturer’s
warranty.
The warranty period commences upon invoice date of the equipment. Wrien noce of breach must be submied to Boyd
Industries, Inc. within this period. Boyd reserves the right to repair or replace, at its sole discreon, the item in queson.
Warranty is voided if items are misused or product is improperly maintained or installed. The warranty does not cover any
alteraon of the product from its original condion or if product is used in any way other than the product’s design intent.
An authorized service technician must perform all service and maintenance. Any warranty labor must be rst approved by Boyd.
Failure to coordinate warranty service may result in denial of warranty repair. Wrien log and receipts for service must be
maintained to validate the warranty on Boyd manufactured products.
No claim for consequenal damages will be allowed. Freight damage or mishandling by any third party will not be considered a
warranty item. Improper installaon by a third party causing damage to the equipment is not a warranty item.
Introducon
Congratulaons
on your purchase of the Boyd PEDO Bench
Boyd Industries, Inc. has spent years designing and developing the best products available in the world today. The following
features make your Boyd product the most advanced and funconal product available in the market:
PB4000 & PB4001:
 Manually adjustable seat back
 Cabinet drawer storage
 Oponal aached light
 Oponal instrument tray
PB4000 Only:
 3-Way Syringe
 Dry hand piece hook up
 Wet hand piece hook up
 High Volume Evacuaon (HVE)
 Saliva ejecon (SE)
 PSI indicator
 Oponal assistant package
 Oponal boled (clean) water system

4
PBM-001
Rev 2
PEDO Bench
Safety Precauons
 Read instrucons:
All safety and operang instrucons including this manual should be read before this product is installed or operated.
 Follow instrucons:
All use and operaon instrucons should be followed.
 Owners manual:
Retain manual for future reference regarding safety and operaon instrucon.
 Heed warnings:
Adhere to all warnings and cauons on the equipment and in the manual.
 Accessories:
Do not use any accessories not recommended by Boyd as they may cause hazards.
 Cleaning:
See General Maintenance and Care secon
 Servicing:
Do not aempt to service this product yourself. Refer any repairs to a qualied service representave.
 Heat / Open ame:
Equipment must be installed away from heat sources such as radiators, heat registers or other sources of heat or open ame.
 Weight restricon:
This bench is designed to safely support a paent weight of 300 lbs. (136.07 kg) that is evenly distributed across the seat. Always
use the anchoring system to ensure stability of this product. Do not aempt to place all of a paent’s weight on the back rest
with it in a raised posion.

5
PBM-001
Rev 2
Descripon of Product Line
About Your PEDO Bench
Model: PB4000 & PB4001
Features: Manual Back
Storage areas
Instrument Tray (Oponal)
Light Assembly (Oponal)
Chair side units (PB4000 only)
Assistant package (Oponal) (PB4000 only)
General Product Informaon
Cabinet: Wood Construcon
Upholstery: Standard upholstery is vinyl
Upgrades are available
Movement: Manual Seat back
Net Weight: 100 lbs (45.35 kg)
Liquid Protecon: Ordinary equipment (IPX1)
Flammable Gases: Not suitable for use in the presence of ammable gases or where such gases may accumulate in
concentraon. (Closed Space)
Operaon Mode: Connuous
Operang Temperature: 5° C to 40° C (41° F to 104° F)
Temperature: Relave Humidity: 20% to 90% @ 30° C - Not condensing
Atmospheric Pressure: 97kPa
Storage / Transportaon Temperature: -10° C TO 50° C (14° F TO 122° F)
Temperature: Relave Humidity: 20% to 90% @ 30° C - Not condensing
Atmospheric Pressure: 45 to 115kPa
Weight Capacity: 350 lbs (158.75 kg) Subject to normal weight distribuon
Note: Do not sit on back of seat secon. This secon is not designed to support the full weight of paent.
Do not li or slide bench using back secon or seat upholstery.
Warning: Do not modify this equipment without authorizaon from Boyd Industries, Inc.

6
PBM-001
Rev 2
27.00
6.50
21.50
25.00
76.00
46.00
18.00
Product Specicaons
PB4000 & PB4001
About Your PEDO Bench (Connued)
Note: Headrest height is adjustable
approximately 6”. TOP VIEW
SIDE VIEW

7
PBM-001
Rev 2
Feature Operaon
About Your PEDO Bench (Connued)
Headrest: The headrest will adjust in and out to comfortably accommodate the paent.
Foot protector: The foot protector snaps on and o for ease of cleaning and replacement.
Backrest: Acvate the release lever on the boom of the back to posion the back secon.
Adjustment release lever is located on the
boom right side of the back secon.
Note: Drawer size, quanty of drawers and toe kick size can be customized per order upon
customer request and aect overall bench height.
Note: Refer to Delivery Unit Product Manual (DSM-
001) for handpiece instrumentaon package.

8
PBM-001
Rev 2
Drawer Removal/Installaon and Adjustment
About Your PEDO Bench (Connued)
Drawer Removal:
1Pull drawer all the way out.
2Press and hold release levers (2) on boom front of drawer and li drawer upward in front unl it is free from slider.
3Disconnue holding release levers.
4Pull drawer o back tabs of slider.
Drawer Installaon:
1Pull sliders (2) all the way out.
2Place drawer loosely on slider.
3Insert tabs on slider (2) into holes (2) on back wall of drawer and front locks should snap into posion.
4Close drawer
Adjustment Height:
Adjust the height of the drawer face by sliding the red tab located under the drawer in the release lever assembly. Push the tab to-
ward the rear of the drawer to raise the drawer face and toward the front of the drawer to lower drawer face.
Release Levers
Drawer Opened Li and Remove
Hole Locaon
Red Adjustment Tab
Tab Locaon
Slider

9
PBM-001
Rev 2
Installaon Procedure
Preassembly Check:
Open shipping cartons carefully and check to see that all parts are received and have not been damaged during shipping.
Unpacking PEDO Bench:
 Remove the plasc banding from the carton.
 Remove the carton top secon.
 Remove the carton side secons.
 Remove the Pedo Bench from the carton by removing the shipping cleats.
Note: Li the pedo bench to move it. Do not slide it or the laminate may get chipped. Do not set bench on any plumbing that
may be hanging from the bench while moving.
Unpacking Procedure
Head if Cabinet to cover in-oor
ulies where applicable
Compartment for water
bole at this end.
Installaon:
 Place the bench in desired posion. Place the head side of the cabinet over ulies where applicable.
 Secure the bench to the oor. There are two (2) angle brackets and two (2) anchors provided with the bench for securing
the bench to the oor. Access the brackets through an opening under the drawers.
 Use supplied #8 x 3/4” long screws to aach angle bracket to bench cabinet.
 Drill holes in oor cement using bracket for posion and vacuum holes to remove dust.
 Install anchors.
Cauon: Failure to anchor the cabinet will create a safety hazard allowing the Pedo Bench to p.
 See “CSU Manual” for delivery unit informaon and ulies.
Anchor
Screws
Angle Bracket
Long side up
Flat Washer
Open Area
Remove drawers
to access
Tools Required:
 Hammer Drill
 5/16 Carbide Masonry Bit
 #2 Phillips Screw Driver
 Vacuum

10
PBM-001
Rev 2
Light Post Installaon (Oponal)
The light post installs in the locaon shown below on either side of the bench for units manufactured aer
January 2012.
Call Boyd Industries for informaon on aaching a light post on units manufactured prior to this date.
Benches ordered with the light post opon will arrive with the T-nuts installed and holes cleared in the cabinet to
aach the light post in the locaon requested. Use the hardware provided to aach the post to the side of the
bench and adjust the leveler pad so that it touches the oor and helps to support the post.
Retrong an exisng bench:
All units manufactured aer January 2012 have the mount T-nuts installed on both sides for adding a light post at
any me. The holes are covered by the exterior laminate and will need to be opened up to allow for mounng.
Drill holes in the laminate with a 3/16” diameter drill bit from inside the cabinet using the exisng T-nut locaons
as a guide. Once located, clear the holes from the outside and aach light post as noted above.
Route the cord from the light thru the
top of the post and out the hole at the
boom of the post.
Note: Be sure that there is a plasc
sleeve insert in the top of the post
before inserng the light.
Route the cord thru the access hole in
the side of the Pedo Bench and
connect it to the power transformer
inside of the bench.
Use the hardware provided to aach the
light post to the side of the Pedo Bench.
Adjust the leveler so that it
touches the oor.

11
PBM-001
Rev 2
Infecon Control
All established infection control policies should be followed. All work surfaces and patient contact surfaces should be disinfected
between patients and at the end of the day using a product that is EPA registered as ‘hospital disinfectant’ and labeled for
‘tuberculocidal’ activity.
PB4000 Only:
 Hand pieces and metal syringe tips must be autoclaved between patients.
Check manufacturer information for details. (270°F @ 20psi for 30 minutes)
 SE, HVE, Tubing, Keyboards and work surfaces must be cleaned and disinfected between patients and at the end of each day.
Use a product that is EPA registered as ‘hospital disinfectant’ and labeled for ‘tuberculocidal’ activity.
Two (2) such products are:
Tri-cide [phone]
Medocadcio [phone]
Do not attempt to clean and re-use disposable tips that are designed for one (1) patient use only.
General Maintenance and Care
Cleaning
It is recommended that the chair and equipment be thoroughly cleaned and disinfected in accordance with the appropriate FDA
guidelines. Use only cleaners and disinfectants approved for cleaning vinyl. Do not use strong or harsh cleaners as they may cause
the vinyl color to fade. Apply the cleaner to a towel, not directly to the vinyl. Refer to vinyl manufacturer’s data on Boyd’s website
for cleaning products. (www.boydindustries.com/support)
Technical Service
For parts, service, or technical information contact:
Worldwide: Boyd Industries, Inc.
12900 44th Street North
Clearwater, Florida USA 33762
tel: [phone] (direct service line)
1-800-255-2693
fax: [phone]

12
PBM-001
Rev 2
Boyd Industries, Inc
12900 44th Street N
Clearwater, FL 33762 U.S.A