Bradley Terreon Classic WF2500 Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
WF2500 Series Terreon Classic
WF2600 Series Terrazzo
WF2700 Series Stainless Steel
WF2800 Series Bradstone
WF3200 Series Terreon Deep Bowl
TDB3100 Series Terreon Deep Bowl
WF3203
215-1833-10 Rev. B; ECN 18-00-009
© 2018 Bradley
Page 1 of 4 7/19/2018
WF2605
Read the instructions in this manual before
beginning installation. Save these instructions
and refer to them for inspection, maintenance
and troubleshooting information.
For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com
or call 800.BRADLEY (800.272.3539).
Product warranties and parts information may also be found under "Products" on our website at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material.
If any parts are missing, do not begin installation until you obtain the missing parts.

Cleaning and Maintenance
WF2500, WF2600, WF2700, WF2800, WF3200, TDB3100 Series
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
2 of 4 7/30/2018 Bradley • 215-1832-10 Rev. B: ECN 18-00-009
Safety Information
Installation
Turn OFF electrical supply to the unit before installation.
Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the
installer.
Proper installation in compliance with industry and government standards for metering faucets requires the following:
1. Adjust volume control until water spray strikes bottom of bowl, 4-inches in from the rim.
2. Air valve metering timing is factory pre-set.
Failure to follow these instructions may negatively affect energy and water use efficiency.
Product/Property Damage
Make sure that all water supply lines have been flushed and then completely turned off before beginning installation.
Debris in the supply lines can cause valves to malfunction.

Cleaning and Maintenance
WF2500, WF2600, WF2700, WF2800, WF3200, TDB3100 Series
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
3 of 4 7/30/2018 Bradley • 215-1832-10 Rev. B: ECN 18-00-009
Cleaning and Maintenance for Terreon®
Material Description: Terreon is a densified solid surface material composed of bio based resin and is resistant to
chemicals, stains, burns and impact. Surface can be easily repaired with everyday cleansers or fine grit abrasives. Because
Terreon is a unique cast material, its aggregate flow and distribution, and shades of color can vary from product to product
creating natural characteristics.
Routine Cleaning: For regular cleaning, use mild neutral base cleaners.
Stubborn Stains: Remove tough stains with Soft-Scrub®and a green Scotch-Brite®pad or lightly sand in a circular motion
with 240 grit wet/dry sandpaper. The finish can then be renewed with a maroon Scotch-Brite pad.
Scratches: Remove scratches with a green Scotch-Brite pad. The finish can then be renewed with a maroon Scotch-Brite
pad.
Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit
thoroughly after cleaning.
Restoring the surface: Use Hope’s®Perfect Countertop to refresh and protect the Terreon Solid Surface material. Dark
Terreon colors may require additional care and maintenance. For complete instructions on this additional maintenance, visit
bradleycorp.com.
Repair Kits: Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing.
Repair kits are made to order and have a shelf life of 30 days.
NOTICE! Do not use strong acid or alkaline chemicals and cleaners to clean Terreon. If these chemicals come in
contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh
chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects.
Cleaning and Maintenance for Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care,
particularly under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more
complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the
cleaning solution per the manufacturer's instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®stainless steel
cleaner or a soft abrasive. Always follow the manufacturer's instructions and apply in the same direction as the polish lines.
NOTICE! Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or
stainless steel brushes.
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in
accordance with the manufacturer's instructions. Many of these products leave a protective coating that helps prevent future
smears and fingerprints.
Grease and Oil: To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the
manufacturer's instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
NOTICE! Do not permit salty solutions to evaporate and dry on stainless steel.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual
source of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
NOTICE! Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of these
cleaners should be avoided.

Cleaning and Maintenance
WF2500, WF2600, WF2700, WF2800, WF3200, TDB3100 Series
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
4 of 4 7/30/2018 Bradley • 215-1832-10 Rev. B: ECN 18-00-009
Cleaning and Maintenance for Terrazzo
Material Description: Terrazzo is a mosaic-looking natural stone and concrete material polished to a high gloss and sealed
with clear polyurethane resin for long lasting beauty. Terrazzo is precast and composed of 85% stone and 15% binder with
steel reinforcing rods cast into the bowl.
Routine Cleaning: Clean daily or as often as conditions require with any standard detergent, warm water and a soft cloth.
Stubborn Stains: If stains have permeated the surface of the terrazzo, follow instructions for restoring the surface listed
below.
Restoring the surface: Use paint stripper to remove the existing polyurethane (it is important to remove all of the old
polyurethane to ensure a high quality finish). Then use light grit sand paper to remove any stubborn staines that have
permeated the surface. Clean and thoroughly dry the bowl. Then apply 2 to 3 coats of polyurethane to the terrazzo
in accordance with the manufacturer's instructions. Allow the polyurethane to dry completely per the manufacturer's
recommendations before turning on the water.
NOTICE! If the bowl is not completely dry before applying the polyurethane, the polyurethane will not adhere to the
surface.
NOTICE! Make sure the surface is completely covered with polyurethane to prevent water from penetrating the
surface and damaging the terrazzo.
Repair Kits: Terrazzo repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing.
NOTICE! Do not place acid or alkaline solutions (floor stripper or drain cleaners) into the terrazzo bowl or use them
to clean the bowl. If these solutions come into contact with the terrazzo, rinse the bowl immediately with
water and inspect for damage. If damage has occurred, follow the directions for restoring the surface. If
bowl begins to haze, it is usually a sign that the terrazzo has come into contact with an acid or alkaline
chemical or has been exposed to UV radiation. To repair this condition, follow the instructions for
restoring the surface.
Cleaning and Maintenance for Bradstone
Material Description: Bradstone is an extremely durable plastic material made of reinforced thermosetting polyester resins,
finely ground inorganic fillers and fade resistant pigments. Bradstone is impervious to most chemicals and stains.
Routine Cleaning: Soap and dirt accumulations should be washed off with detergent cleaners. Abrasive and caustic
cleaners are not recommended. An occasional waxing with automotive wax will make future cleaning even easier.
Brand Names
Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the
omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found
in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.

1 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
This document describes installation of washfountain bowl and pedestal only. Some optional equipment and
accessories are shown for clarity. For activation, optional equipment and accessory installation, see installation
documents included with those parts.
Supplies Required by Installer
• (6) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal
• 1" hot and cold water or tempered supply lines and fittings (see activation instructions)
• Reducing fittings and 1/2" nom. copper tubing supply lines for types with supplies from above (see
activation instructions)
• Standard P-trap (vented trap supplied by Bradley when required)
• 2" drain lines and fittings (see activation instructions)
• 1-1/2" vent pipe on types vented through washfountain column
• Pipe sealant and plumber's putty
Before installation of bowl and pedestal assemblies, review all included instructions. Some options may require
additional steps during the bowl and pedestal installation process.
Supply lines for one or two washfountains should be 1"; for three washfountains 1-1/4"; for more than three
washfountains, pipe size should increase proportionally. Vent pipe to be 1-1/2" on models vented through
washfountain.
Valving installations for Classic washfountains require rigid plumbing installation and connections to ensure
proper operation and support of the valve assemblies, especially for foot control activated washfountains. Do
not use flexible supply hoses unless specified in your activation instruction documentation and supplied with
your washfountain.

2 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Circular Washfountain Dimensions
Adjust to Towel Dispenser
Mounting Holes
K
(mm)
6" (152)
J
G
H
E
A
B
C
D
F
Approximate Dimensions in Inches*
Material Size A B C D E F G H J K
Terrazzo 54" 19 29-1/4 39-1/8 47-5/8 36-1/4 56 23-1/4 21-1/2 32-1/4 5-1/4
Stainless 54" 19 28 37-3/8 45-7/8 32-1/4* 54-1/4 26-1/4 24-1/4 35-1/4 8-1/4
Terrazzo 36" 19 29-1/4 35-5/8 44-1/8 33-1/4 52-1/2 17-1/4 15-1/4 22-3/4 4-3/4
Stainless 36" 19 28 33-7/8 42-3/8 32-1/4* 50-3/4 20-1/4 18-1/ 25-3/4 7-3/4
* Only when backsplash is specified; otherwise "B" applies. For juvenile height (Terrazzo only), subtract 4" from dimensions A-F.
Approximate Dimensions in Millimeters*
Material Size A B C D E F G H J K
Terrazzo 1372mm 483 743 994 1210 921 1422 591 546 819 133
Stainless 1372mm 483 711 949 1165 819* 1378 667 616 895 210
Terrazzo 914mm 483 743 905 1112 845 1334 438 378 578 121
Stainless 914mm 483 711 860 1076 819* 1289 514 464 654 197
* Only when backsplash is specified; otherwise "B" applies. For juvenile height (Terrazzo only), subtract 102mm from dimensions A-F.

3 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Length of Tie Pipe Required for Vent Through Washfountain Column
Type Pipe Length
54" Less Soap Dispenser 21-1/2" (543mm)
36" Less Soap Dispenser 18" (457mm)
54" with Soap Dispenser 30" (762mm)
36" with Soap Dispenser 26-1/2" (673)
54" Less Soap Dispenser with Towel Dispenser 55-1/2" (1410mm)
36" Less Soap Dispenser with Towel Dispenser 52" (1321mm)
54" with Soap Dispenser with Towel Dispenser 48" (1213mm)
36" with Soap Dispenser with Towel Dispenser 44-1/2" (1130mm)
54" with Cube Adapter 32" (813mm)
36" with Cube Adapter 28-1/2" (724mm)
54" with Cube Adapter with Towel Dispenser 50" (1270mm)
36" with Cube Adapter with Towel Dispenser 46-1/2" (1181mm)
54" with Cube Adapter and Soap Dispenser 40" (1016mm)
36" with Cube Adapter and Soap Dispenser 36-1/2" (927mm)
Drain must be connected with 2" schedule 40 welded wrought iron pipe, minimum, to provide lower
support for this installation. Vent or support pipe must be of the same material in 1-1/2". For detailed
tie pipe information, see 215-1834-26.

4 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
(mm)
Rough-In Specifications
Type A
Off-line vent with
supplies from below
1" NPT Supplies
Through Wall
Tr a p
36" (914) Washfountain Bowl
2" NPT Supplies Through Floor: Stub
Up 3" (76) Above Floor
Cold
Hot
2" NPT Drain Through Wall (Stub
Out to Suit Trap Dimension)
54" (1372)
Washfountain Bowl
Centerline of Drain to
Centerline of Fixture
See Table on
page 8
7-5/8"
(194)
Installing Traps
When installing trap with a coupling and nipple, see
dimension A in Table on page 8. If trap is installed
tight to bottom of bowl, dimension A depends on
design of trap.
*B - Wall to centerline of trap
**A - Centerline of drain to floor
B*
4"
(102)
1" NPT Supplies Through Floor (Optional)
Stub Up 2-1/2" (64) Above Floor
Trap for Wall
Outlet Only
Wall
Wall
Drain
Through Wall
4" (102) Clearance Hole
Top View
Side View
A**
See Table on
Page 8
Supplies
Through Wall Drain & Supplies Through
Floor Trap Located Below
Floor (Optional)
12" (305) for Standard Height
8-1/4" (210) for Juvenile Height
Floor
Some optional equipment shown.
Rough-In Notes
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1", for three washfountains 1-1/2"; for more than three washfountains,
pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
UPC and IPC restrict the vertical
distance from the fixture outlet to
the trap weir to not more than 24".
Check state and local codes for
variances.

5 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Some optional equipment shown.
(mm)
Rough-In Specifications
Type O
Off-line vent with
supplies from above
1" NPT Supplies from
Above Must Reduce to 1/2"
Nominal Copper Tube on
These Centers to Pass thru
Washfountain
Tr a p
36" (914) Washfountain Bowl
2" NPT Supplies Through Floor
(Optional) Stub Up 3" (76) Above Floor
Cold
Hot
2" NPT Drain Through Wall (Stub
Out to Suit Trap Dimension)
54" (1372)
Washfountain Bowl
Centerline of Drain to
Centerline of Fixture
See Table on
page 8
7/8"
(22)
Installing Traps
When installing trap with a coupling and nipple, see
dimension A in Table on page 8. If trap is installed
tight to bottom of bowl, dimension A depends on
design of trap.
*B - Wall to centerline of trap
**A - Centerline of drain to floor B*
4"
(102)
Trap for Wall
Outlet Only
Wall
Wall
Drain
Through Wall
4" (102) Clearance Hole
Top View
Side View
A**
See Table on
Page 8
Supplies
Through Wall
Drain & Supplies Through
Floor Trap Located Below
Floor (Optional)
Floor
Some optional equipment shown.
Rough-In Notes
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1", for three washfountains 1-1/2"; for more than three washfountains,
pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
UPC and IPC restrict the vertical
distance from the fixture outlet to
the trap weir to not more than 24".
Check state and local codes for
variances.
7/8"
(22)
1-1/4"
(32)

6 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
(mm)
Rough-In Specifications
Type B
Centrally Rising Vent
with Supplies from
Above
1" NPT Supplies from
Above Must Reduce to 1/2"
Nominal Copper Tube on
These Centers to Pass thru
Washfountain
36" (914) Washfountain Bowl
1-1/2" NPT Vent
to Ceiling
Cold
Hot
2" NPT Drain (Make Stub
3" (76) Above Floor)
54" (1372)
Washfountain Bowl
See Table on
page 8
7/8"
(22)
B*
4"
(102)
Wall
Wall
Drain
Through Wall
Top View
Side View
Drain Through Floor
Floor
Some optional equipment shown.
Rough-In Notes
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1", for three washfountains 1-1/2"; for more than three washfountains,
pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
5. For maximum rigidity of sprayhead/support tube assembly, use 1-1/2" NPT galvanized pipe for vent. Use of plastic or copper
for vent is not recommended.
7/8"
(22)
1-1/4"
(32)
Vent

7 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
(mm)
Rough-In Specifications
Type H
Centrally Rising Vent
with Supplies from
Below
1" NPT Supplies
through Wall
36" (914) Washfountain Bowl
1-1/2" NPT Vent
to Ceiling
Cold
Hot
2" NPT Drain (Make Stub
3" (76) Above Floor)
54" (1372)
Washfountain Bowl
See Table on
page 8
7-5/8"
(194)
B*
4"
(102)
Wall
Wall
Supplies
Through Wall
Top View
Side View
Drain Through Floor
Floor
Some optional equipment shown.
Rough-In Notes
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1", for three washfountains 1-1/2"; for more than three washfountains,
pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
5. For maximum rigidity of sprayhead/support tube assembly, use 1-1/2" NPT galvanized pipe for vent. Use of plastic or copper
for vent is not recommended.
3-1/4"
(83)
Vent
Supplies Through Floor
(Optional)
7-5/8"
(194)
1" NPT Supplies Through Floor (Optional)
Stub Up 2-1/2" (63) Above Floor
12" (305) for Standard Height
8-1/4" (210) for Juvenile Height

8 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
1Installing the Drain
ARough in supply and drain piping as
required for your installation.
BAssemble the drain to the dimension
shown below for the bowl size you are
installing.
All piping shown in dotted lines
to be supplied by installer.
Trap Dimensions (mm)
A B C
Bowl Material & Size Standard Height Juvenile Height Standard Height Juvenile Height
54" Terrazzo 6" (152) to 13-1/4" (336) 6" (152) to 10-1/4" (260) 5-1/4" (133) 18-5/8" (473) 14-5/8" (371)
36" Terrazzo 6" (152) to 13-1/4" (336) 6" (152) to 10-1/4" (260) 4-3/4" (121) 18-5/8" (473) 14-5/8" (371)
54" Stainless Steel 6" (152) to 11-5/8" (295) N/A 8-1/4" (210) 17" (432) N/A
36" Stainless Steel 6" (152) to 12" (305) N/A 7-3/4" (197) 17-3/8" (441) N/A
Types A, O
Drain (Through
Floor - Optional)
A
B
Types B, H
Drain (Through
Floor - Optional)
CB
9-3/4"
(248)
Vented Trap
(111-024)
Types A, O
Tie Pipe Bracket
(Optional)
C
B

9 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
2a Assembling the Pedestal (with Foot Control)
AAssemble the legs and scuff base
panels with the 5/16" carriage bolts
and nuts provided.
BAttach the pedestal frame members with
the 5/16" stove bolts and nuts provided.
CAdd the foot levers to the pedestal
assembly.
DAdd the pivot bolts, elevator bolts and
foot rail.
2b Assembling the Pedestal (without Foot Control)
AAssemble the legs and scuff base
panels with the 5/16" carriage bolts
and nuts provided.
BAttach the pedestal frame members
with the 5/16" stove bolts and nuts
provided.
Blank Plate (169-424)
(install between scuff
base and leg)

10 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
CAUTION! Use suitable lifting equipment
to position bowl and pedestal
assembly. Handle with care! Failure
to do so could result in serious
personal injuries.
APlace the bowl on the pedestal using
suitable lifting equipment.
B
Fasten the bowl to the pedestal with
the four flat head stove bolts provided.
Place the bowl clip inside the pedestal
leg.
NOTICE! The pedestal must be level when
secured to floor for proper drainage.
Pedestal Anchoring Dimensions (mm)
A B C
Bowl Material &
Size Std. Height Juv. Height
36" Terrazzo 11" (279) 8-5/8" (219) 18-1/4" (464) 14-1/4" (362)
54" Terrazzo 16-1/2" (419) 14-1/8" (359) 18-1/4" (464) 14-1/4" (362)
36" Stainless Steel - 8-5/8" (219) - -
54" Stainless Steel - 14-1/8" (359) - -
3Bowl Assembly and Mounting
There is some spring in the brackets.
Adjust the brackets so that the bowl is
flush with the wall before securing in
place.
CPosition the bowl and pedestal
assembly so that the bowl drain is in
line with the trap or drain line.
DScrew the drain spud part of the
way into the drain to ensure correct
alignment.
EAnchor the pedestal assembly to the
floor and wall with suitable anchors/
fasteners (supplied by installer).
Pedestal Assembly
CAUTION! Bowl surface is smooth. Use suitable lifting equipment to position bowl and pedestal assembly.
Handle with care!
APosition the pedestal as shown in
pedestal assembly drawing.
BPlace the bowl on the pedestal using
suitable lifting equipment, making sure
that the bowl drain is in line with the
trap or drain line.
CAnchor the pedestal assembly to the
floor and wall with suitable anchors/
fasteners (supplied by installer).
For Stainless Steel Bowl
For Terrazzo Bowl
Some optional equipment shown.

11 of 11 1/29/2018 Bradley • 215-1833-3 Rev. A: ECN 17-00-021A
Bowl and Pedestal Assembly (Stainless Steel & Terrazzo)
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
4Installing Drain Spud in Bowl
ASecure drain spud with lock nut and
washers as shown.
Seal between drain spud and drain hole
with plumber’s putty (supplied by installer).
Strainer
(S45-067)
Spud
Terrazzo (112-015)
Stainless Steel (112-016)
Washer
(142-068)
Bowl
Locknut
(161-021)

1 of 2 1/24/2019 Bradley • 215-1834-21 Rev. B: ECN 19-00-002
Sprayheads
WF2500, WF2600, WF2700, WF2800, WF3200, TDB3100 Series
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Non-Sectional Sprayhead
Repair kit does not include sprayhead grommet. Order as a separate item.
1
2
345
9
6
8
7
10
Parts List
Item Part No. Description
Sprayhead
Assembly
Repair Kit
S45-051
Qty
1 125-001DE Neoprene Washer - Top 1 1
2 139-031 Sprayhead Manifold 1 -
3 124-001AL Washer 3 4
4 160-211 Carriage Bolt 3 4
5 115-061 Sprayhead Top 1 -
6 116-008 Sprayhead Bottom 1 -
7 124-001AT Washer 3 4
8 161-025 Nut 3 4
9 124-020C Sprayhead Grommet - Circle 1 -
9 120-020D Sprayhead Grommet - Semi-Circle 1 -
9 120-020E Sprayhead Grommet - Corner 1 -
10 125-001DF Neoprene Washer - Bottom 1 1

2 of 2 1/24/2019 Bradley • 215-1834-21 Rev. B: ECN 19-00-002
Sprayheads
WF2500, WF2600, WF2700, WF2800, WF3200, TDB3100 Series
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Sprayhead Troubleshooting
Problem Cause Solution
Water splashes over
the rim of the bowl.
Foreign matter has reduced the size of
the sprayhead slots, causing greater
pressure at the open slots.
Clean the sprayhead:
1. Disassemble the sprayhead and dislodge any dirt,
lime build-up and foreign debris with a wire brush.
2. Sprayheads with rubber grommet spray rings may
be cleaned by rubbing a coin over the grommet.
Throttle down the volume control (water spray should strike
the bowl without splashing outside of the bowl).
Water flow diminishes
from the sprayhead.
Strainer portion of the stop-strainer-check
valve is plugged.
Remove and clean the strainer screen from the stop-
strainer-check valve.
The non-sectional sprayhead includes a
perforated neoprene spray ring grommet that is
self-cleaning. The water pressure flexes the spray
holes which slows accumulation of foreign matter
and tends to "break loose" any such deposits that
may have accumulated.
Sprayhead Tubing Connections
WARNING Flush supply lines before making connections.
AUsing a sharp razor, cut tubing squarely
and remove any burrs. DO NOT pinch or
crush end of tubing.
B
Loosen nut on fitting. Moisten end of
tube and push into fitting until it is firmly
seated. Tighten nut to secure tube
to fitting (make sure nut is securely
tightened).
C
If connector leaks, reseat tubing
according to above procedure. If leaking
persists, replace male connector, or call
a Bradley representative for assistance.
Tubing
Sprayhead
Tubing
Nut
Male Tube
Connector
(269-626)

1 of 11 2/13/2018 Bradley • 215-1834-28 Rev. A: ECN 17-00-020
Air Metering Activation Modules - Non-Sectional Semi-Circular Washfountains
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
Supplies Required by Installer
• Pipe sealant and plumbers putty
• 1-1/2" vent pipe on types vented through washfountain column
Pre-Installation Information
Cylindrical Air Valve
The air valve pushbutton allows each user to activate an air metering valve (starting the flow of water) by pushing
and releasing the pushbutton. The air metering valve is factory-preset to run for 10 seconds and can be adjusted to
run from 5-60 seconds.
Not all equipment shown in this document is available on all washfountains shown within these
pages. See Tech Data for optional equipment available for your washfountain.
Supply lines for one or two washfountains should be 1"; for three washfountains 1-1/4"; for more than three
washfountains, pipe size should increase proportionally. Vent pipe to be 1-1/2" on models vented through
washfountain.

2 of 11 2/13/2018 Bradley • 215-1834-28 Rev. A: ECN 17-00-020
Air Metering Activation Modules - Non-Sectional Semi-Circular Washfountains
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
1a Air Metering Valve Assembly – A and O Units
B
Place sprayhead with 1/2" tubing onto
support tube. Run the tubing down
through the support tube and connect to
valve tube connector.
C
Assemble the lower tie rod (the longer
threaded rod), upper tie bar (notched at
corners), lower tie bar, tie rod nut and
coupling nut, then attach the 4-1/4" tie rod
to coupling nut.
D
Place the air metering module assembly on
top of sprayhead. Rotate until module locks in
with tie bar. Run 1/8" diameter tubing through
the support tube down into the pedestal. and
connect to the air valves, taking care that
each sprayhead section's 1/2" supply tube
and 1/8" activation button tube are connected
to the same valve (see detail in Step 2).
Skip to step F for units without soap.
E
For units with soap option, install the spacer,
soap dispenser and cover using coupling
nut, soap tie rod (8-5/8" long) and second
coupling nut as shown.
FSecure module cover and dispenser cover
with acorn nut and set screw.
GConnect supply stops onto stub-outs.
Connect flexible hoses to supply stops.
AInstall hemmed end (not sharp end)
of support tube with gasket onto bowl.
Connect 1/2" dia. tubing to sprayhead.
• Using a sharp razor, cut tubing squarely
and remove any burrs. DO NOT pinch
or crush end of tubing.
• Loosen nut on fitting. Moisten end of
tube and push into fitting until it is firmly
seated. Tighten nut to secure tube
to fitting (make sure nut is securely
tightened).
• If connector leaks, reseat tubing
according to above procedure. If leaking
persists, replace male connector, or
call your Bradley representative for
assistance.
H
FOR O UNIT: Install 1/2" nominal copper
tubing supply lines (pass them through holes
in cover down through support column) and
connect to stops using suitable fittings.

3 of 11 2/13/2018 Bradley • 215-1834-28 Rev. A: ECN 17-00-020
Air Metering Activation Modules - Non-Sectional Semi-Circular Washfountains
WF2603, WF2604, WF2703, WF2704
P.O. Box 309 •Menomonee Falls, WI 53052-0309 • 1 800 BRADLEY •262 251 6000 •bradleycorp.com
1a Air Metering Valve Assembly – A and O Units
Type "O" Drain
Supplies from Above
Type "A" Drain
Acorn Nut (110-052A)
Set Screw (160-093)
Dispenser Cover
Soap Dispenser Soap
Dispenser Lid
4-1/4" Module Tie Rod
(176-118)
8-5/8" Soap Tie
Rod (176-010)
Spacer
(113-155A)
Coupling Nut (110-051D)
Set Screws (160-208)
Sprayhead
(S05-054B) See 215-1834-21
for Supply Connections.
Lower Tie Rod
36" (176-008)
54" (176-008A)
Support Tube
(S57-005, 54")
S57-006, 36")
3/8" Supply Tube
Gasket
(125-011, Terrazzo)
(125-008, Stainless Steel)
Lower Tie Bar
(159-009)
Tie Rod Nut
(110-064)
Set Screws
(160-208)
Some optional equipment shown.
Parts Shown in Box
are for Units with
Soap Dispenser
Tab Fits Into
Dispenser Cover
Air Module Assembly
(S65-427)
Coupling Nut (110-051D)
Set Screws (160-208) Upper Tie Bar (159-009A)
(Notched at Corners)