Bradley Verge Crestt Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
Table of Contents
Safety Information..................................2
Supplies Required ..................................2
Dimensional Information .............................3
Faucet Components ................................4
Mount Faucet on Deck ..............................5
Connect Water and Electrical Supply ..................6
Adjust Temperature with Running Water ................7
Test Unit..........................................7
Multi-Faucet Wiring.................................8
Adjusting the Control Module.........................8
Troubleshooting – Solenoid Valve .....................9
Troubleshooting – Thermostatic Mixing Valve ............9
LED Indicators.....................................9
215-1895 Rev. B: ECO 21-02-022
© 2021 Bradley
Page 1 of 9 9/3/2021
Verge™Faucet - Crestt Series (S53-3100)
Verge™Faucet - Metro Series (S53-3300)
Verge™Faucet - Linea Series (S53-3500)
Verge™Faucet - Zen Series (S53-3700)
Read the instructions in this manual before beginning installation. Save these
instructions and refer to them for inspection, maintenance, and troubleshooting
information.
For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com
or call 800.BRADLEY (800.272.3539).
Product warranties and parts information may also be found under “Resources” on our website at
bradleycorp.com.

29/3/2021 Bradley • 215-1895 Rev. B: ECO 21-02-022
Verge™ Faucets Installation
Supplies Required
• 120V/220V 50/60Hz power source when using Bradley supplied 120V AC/6V DC plug-in adapter
• Tempered hot and cold supply piping and fittings to solenoid valve (1/2" NPT)
• Pipe fittings, pipe sealant as required
Safety Information
Warning
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
Caution
A DC plug-in adapter (supplied by Bradley) should be used in conjunction with the Bradley supplied faucets. The
DC plug-in adapter supplied by Bradley is 6V DC regulated. Direct connection to 120V/220V 50/60Hz could result in
personal injury and will damage the sensor.
Important
Separate parts from packaging and make sure all parts are accounted for before discarding packaging material. If
any parts are missing, do not begin installation until you obtain the missing parts.
When the faucet is mounted on a fixture with a stainless steel bowl, it is recommended that the bowl have a satin
finish rather than a mirrored or highly polished finish.

3Bradley • 215-1895 Rev. B: ECO 21-02-022 9/3/2021
Installation Verge™Faucets
Dimensional Information (mm)
5-15/16"
(150)
7-11/16"
(195)
6-3/16"
(157)
5-5/16"
(135)
4-7/8" (123)
5-3/4" (146)
5-1/2"
(139)
3-5/8"
(93)
6-1/4"
(159)
5-1/4"
(133)
5-1/2"
(140) 4"
(102) 3-7/8"
(98)
4-5/8" (119)
4-13/16" (122)
6-1/2"
(165)
5-5/8" (142)
5-3/4" (146)
4-7/16" (112)
4-13/16"
(122)
5-3/8" (136)
sensor centerline
sensor centerline
sensor centerline
sensor centerline
water
water
water
water
3500 Linea Series 3700 Zen Series
3100 Crestt Series 3300 Metro Series

49/3/2021 Bradley • 215-1895 Rev. B: ECO 21-02-022
Verge™ Faucets Installation
Faucet Components
Washer
Faucet Gasket
Faucet Body
Male Connector
Faucet Shank
Faucet Supply
Tube
Faucet Sensor
Cable
Pod, Body, Flow Control
#4-40 Screw
Sensor Assembly
#10 Screw
Locking Nut

5Bradley • 215-1895 Rev. B: ECO 21-02-022 9/3/2021
Installation Verge™Faucets
Mount Faucet on Deck
1
ADrill holes in deck to the size and
position for your faucet configuration.
BAttach faucet securely to deck.
Washer
Deck
1" (25.4 mm)
Drilled Hole (1-1/4" max)
Faucet Shank
Faucet cable is routed
into control box and clips
into control module.
Locking Nut w/ Screws
Route faucet cable & tube through
shank center opening, washer,
and nut.
When installing a faucet to a new deck
installation, it is advisable to assemble
faucet to deck when deck is on hard floor
surface prior to deck attachment to wall
for ease of assembly.

69/3/2021 Bradley • 215-1895 Rev. B: ECO 21-02-022
Verge™ Faucets Installation
Connect Water and Electrical Supply
Thermostatic Valve Assembly and Tempered Line
2
Typical Faucet
Head Assembly
Deck
Sensor Harness
Solenoid
Control Box
120VAC/6V DC Plug-in Adapter
(optional selection)
Battery carrier
connector in this slot.
Battery pack included.
Operates as battery
backup if using plug-in
adapter.
Route sensor cable through
opening to control module
and clip in connector.
Shank Locking Nut - Torque (2) screws
to 25 in-lb to prevent rotation.
1/4" Inline Connector
(supplied)
1/4" O.D. Tube
30" max length,
IPC section 604.5;
UPC section 604.12
Cold Inlet
Cold Supply
Hot Supply
See illustration on right
for tempered supply view.
Thermostatic Valve
Assembly shown.
Hot Inlet
Route wires from
solenoid through
opening.
• Slide tube through compression nut.
• Seat tube into solenoid.
• Hold supply tube in place, and then
hand-tighten compression nut.
Connection is
made here.
Control Module
Supply line must use a flexible hose, plastic hose
& fitting, or soft copper tubing for supply inlets.
Route adapter wire through
this opening to control box.
Connect faucet supply tube
to solenoid.
OR
Compression
Nut
Tempered
Supply
Compression
Nut

7Bradley • 215-1895 Rev. B: ECO 21-02-022 9/3/2021
Installation Verge™Faucets
H
C
DO NOT SKIP THIS STEP!!!
This valve is NOT factory preset. Upon installation, the temperature of this valve must be checked and
adjusted to ensure delivery of a safe water temperature. Water in excess of 110°F (43°C) may cause scalding.
This step only applies for units equipped with a TMA Navigator Mixing Valve.
Adjust Temperature with Running Water
3
ALoosen cap screw about 1/4" (4-6 turns)
and lift up cover (do not remove).
B
Using cover, turn cartridge gently until
desired water temperature is reached. Do
not turn past stops as this may damage
unit. Push cover down and tighten screw.
Test Unit
4
This step only applies for units equipped with a TMA Navigator Mixing Valve.
A
Shut the hot water inlet off by closing
hot water inlet valve. While the hot
water supply is turned off, check
to make sure the cold water flow is
reduced. If the cold water is reduced
properly, reopen the hot water supply.
B
Shut the cold water inlet off by closing
the cold water inlet valve. While the cold
water supply is off, check to make sure
that the hot water flow has shut down.

89/3/2021 Bradley • 215-1895 Rev. B: ECO 21-02-022
Verge™ Faucets Installation
Multi-Faucet Wiring
One optional plug-in adapter
splitter kit operates up to four
faucets at one time. Additional
plug-in adapter(s) or splitter kits
are required for installations with
more than four faucets.
Adjusting the Control Module
The control module is set at the factory with the selector switch
in position 5. This provides a 11 second run time.
Switch position 1 allows a manual
override of the solenoid to allow the
solenoids to flow continuously.
Switch positions 0, 2, and 3 do not apply
to this product.
To adjust the control module to a
different time out period, turn the
selector switch to the desired time out
setting (4 through 9 for no flush,
A though F for 24 hours flush) as
indicated on the module label.
A
The 24 hour flush function will activate water flow for a period
of 60 seconds any time there has been no activation within the
past 24 hours. This function is used to help clear stagnant water
from the plumbing system and can provide some measure of
prevention against the formation of bacteria in supply pipes.
114-383 Rev B
S83-440 Timer
Red = Disabled Green = Activated
Diagnostic - See Instructions
0: Test Timer Module I/O
1: Solenoid Open
Custom - See Instructions
2: Push Button Light On/Off
3: Timeout Period
Timeout Setting
4: 4s, no flush
5: 11s, no flush
6: 15s, no flush
7: 30s, no flush
8: 60s, no flush
9: 180s, no flush
A: 4s, 24hr flush
B: 11s, 24hr flush
C: 15s, 24hr flush
D: 30s, 24hr flush
E: 60s, 24hr flush
F: 180s, 24hr flush
12V Monostable Solenoid
12V DC Plug-in Adapter
Indicators
BATTERY
Connector for
Sensor Cable
LED Indicator
AC Adapter Splitter
Kit
Selector Switch
Power Adapter
Connection
Battery Carrier
Connection
Control Module

9Bradley • 215-1895 Rev. B: ECO 21-02-022 9/3/2021
Installation Verge™Faucets
Troubleshooting – Solenoid Valve
Problem Cause Solution
Faucet fails to shut off and drips. The cartridge valve is defective. Replace cartridge with part number S27-352A.
Faucet fails to turn on. A failed valve or loose electrical
connection to the connectors.
1. Repair loose connection.
2. If possible, determine whether sensor, power adapter
or valve is defective by swapping parts with an adjacent
faucet. Replace defective part.
Faucet doesn't activate. Blocked sensor. 1. Clean sensor lens with soft, damp cloth.
2. Unplug power supply or remove batteries.
3. Reconnect power supply or install new batteries.
Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions:
• If stop valves are used, make sure that they are fully open.
• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-
connections or leaking stop valves.
• Check the hot water heater output to make sure that it is at least 10°F above the set temperature.
Troubleshooting – Thermostatic Mixing Valve
LED Indicators
Close the appropriate shut-off valves prior to disassembly and reopen valves after inspection and
repair is complete.
Problem Cause Solution
External leaks. Damaged cartridge or
O-rings.
Replace cartridge with part number 269-1927.
Improper water temperature
or temperature fluctuation.
Hot water supply is not
10° above desired set
point.
Increase hot water supply temperature.
Valve temperature is not
properly set.
Adjust the temperature as shown on page 4 step 3.
Limited water flow. Dirt and debris have built
up in the valve or strainer.
1. Check to make sure both hot and cold supplies are connected to
the Navigator mixing valve and that they have water flow.
2. Remove cover and U-clip. Remove the cartridge and clean the
strainer. It is not required to grease cartridge, however if desired,
use silicone grease only.
Do not use grease on check valves.
LED Indicator Cause Solution
Flashing red LED. Low battery. Replace 4 AA batteries and activate faucet.
Rapid red flashing LED. Blocked sensor communication. Power cycle.
Green constant flashing LED upon
initial startup.
Debris on plastic cover. Clean plastic cover.
Red flashing LED upon initial
startup.
Hardware issue with TOF sensor. Power cycle.
Problem