Bradley S19-465EFW User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Installation
215-1170 Rev. K; EN 06-515
© 2006 Bradley Corporation
Page 1 of 4 6/23/06
S19-465EFW
Deck-Mounted Hand-Held
Drench Hose
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . .3
Assembly of Components . . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2
S19-465EFW Installation
6/23/06 Bradley Corporation • 215-1170 Rev. K; EN 06-515
Pre-Installation Information
Operation
Water flows when the handle on the valve is squeezed and remains open while squeezed.
Components
Sprayhead: Perforated sprayhead provides soft spray for cleansing eyes and face. The integral flow
control assures safe, steady flow under varying water supply conditions from 30-90 PSI. NOTE: The
ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI flow
pressure.
Drench Hose: The 8' (2438mm) hose has a 3/8" IPS male thread with a removable 1/2" x 3/8"
female reducing coupling.
Supplies Required
• 1/2" IPS water supply
• Sign-mounting hardware
• Backflow prevention device as required by UPC, IPC and/or local plumbing codes
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff. Flushing fluid should be tepid per ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should
be trained regarding the placement and proper operation of emergency
equipment per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List




P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

Installation Instructions
Step 1: Prepare deck for installation
1. Rough-in 1/2" IPS supply piping from
wall where drench hose is desired
(piping supplied by installer).
2. Select desired location in deck for drench
hose and drill a 1-5/16" (34mm) diameter
hole.
3. Install the drain plug using the washers
and locknut provided (see Figure 2 and
the parts list, page 4).
Step 2: Install drench hose
1. Install the drench hose assembly as
shown in Figure 2 on page 4.
Step 3: Connect water supply
1. Connect the end of the drench hose to the
1/2" IPS water supply.
2. Mount the safety sign to the wall using
the sign-mounting hardware supplied by
installer.
3. Open the water supply line. Test for
leaks and adequate water flow.
3
Installation S19-465EFW
Bradley Corporation • 215-1170 Rev. K; EN 06-515 6/23/06
11-3/4"
(298mm)
2-1/4" (57mm)
MININUM
DISTANCE
FROM WALL
5-1/4"
(133mm)
Figure 1

Assembly of Components and Parts List
4
S19-465EFW Installation
6/23/06 Bradley Corporation • 215-1170 Rev. K; EN 06-515
3
2
8
10
7
6
5
9
11
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
4.2
4.3
4.1 4
P.O.BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
1.1
1
Figure 2
1 S27-265 1 Valve Assembly
1.1 269-661 1 Valve Handle only
2 153-337 1 Adapter
3 153-380 1 Adapter
4 S05-148 1 Sprayhead Assembly
4.1 S05-147 1 Angled EFW Assembly
4.2 S05-135 2 Sprayhead
4.3 S53-063 2 Dust Cover
5 S29-092 1 Drain Flange Assembly
6 125-001CE 1 Washer, Rubber
7 169-875 1 Washer
8 S89-002 1 3/8" Yellow Tube
9 169-059 1 Reducing Coupling
10 204-421 1 Emergency Tag
11 114-051 1 Safety Sign
Item Part No. Qty Description Item Part No. Qty Description