Bradley S19-220SS User manual

Installation
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
215-158SS Rev. M; ECN 12-05-033
© 2013 Bradley
Page 1 of 4 3/19/2013
S19-220SS
Stainless Steel Wall-Mounted
Eyewash
Table of Contents
Pre-Installation Information ................... 2
Installation Instructions ...................... 3
Assembly of Components .................... 4
Parts List ................................. 4

2
S19-220SS Installation
3/19/2013 Bradley • 215-158SS Rev. M; ECN 12-05-033
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley
plumbed emergency fixtures require a minimum of 30 PSI (0.21 MPa) flowing pressure.
Flushing fluid should be tepid per ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to ensure
compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per
ANSI Z358.1.
For questions regarding the operation or installation of this product, visit www.
bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under “Product Information” on our web site at
www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O.Box309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

3
Installation S19-220SS
Bradley • 215-158SS Rev. M; ECN 12-05-033 3/19/2013
Installation Instructions
Supplies Required:
• (2)1/4"boltsandwallanchorsformountingwall
bracket
• Pipesealant
• Pipingto1/2"NPTwatersupplyinletonunit
• Pipingto1-1/4"NPTdrainoutletforeyewash
• Sign-mountinghardware
Step 1: Install wall bracket
NOTE: The top of the eyewash heads should be
33"–45" (838mm–1143mm) from the floor.
1. Positionthewallbracketonthewall.
2. Usingthewallbracketasatemplate,mark
theboltholelocationsonthewallORinstall
twosuitablefasteners(suppliedbyinstaller)
for1/4"boltsinthewallatthemarkedhole
locations.
3. Boltthewallbrackettothewallorwall
fastenersusing3/8"bolts(suppliedby
installer).
Step 2: Assemble eyewash
components
1. Assembletheremainingcomponentsas
shownonpage4.
•Applypipesealant(suppliedbyinstaller)to
allmale-threadedpipejoints.
Step 3: Connect water supply
1. Connectthewatersupplypipingtothe1/2"
NPTinletontheeyewash(pipingsuppliedby
installer).
2. Connectdrainpipingtothe1-1/4NPTdrain
outletontheeyewash(pipingsuppliedby
installer).
3. Mountthesafetysigntoawallorpipe
usingsignmountinghardware(suppliedby
installer).
4. Openthewatersupplylines.Testforleaks
andadequatewaterflow.
36"
(914mm)
Suggested
Height To
Floor
30-1/2"
(775mm)
Suggested
Height To
Floor
Wall

4
S19-220SS Installation
3/19/2013 Bradley • 215-158SS Rev. M; ECN 12-05-033
Assembly of Components and Parts List
1.1
1.2
1.3
1.4
1.5
1.6
1.9
1.8
1.10
1.11
1.14
2
34
6
7
8
1.7
1
P.O.Box 309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich imTestbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
1.12 1.13
5
4.1
9
10
NOTE: Items 1.1–1.14 come preassembled as Item 1.
Item Part No. Qty Description
1 S90-318 1 StainlessSteelEyewashAssy.
1.1 111-049 1 Inlet-DrainFitting
1.2 124-028 1 Gasket
1.3 140-645 1 Wall Bracket
1.4 124-024 1 Gasket
1.5 187-053 1 StainlessSteelEyewashBowl
1.6 173-009 1 Cup Strainer
1.7 S21-074 1 Supply Pipe
1.8 113-1159 1 Spacer, Drain
1.9 S05-131 1 EyewashYoke
1.10 107-371 2 Dust Cover
1.11 269-912 1 SwivelStem
1.12 124-055 2 QuadRing
Item Part No. Qty Description
1.13 S57-148 1 SprayRingAssembly
1.14 110-209 1 Acorn Nut
2 113-965 1 Pipe,StainlessSteel1/2"x3-1/2"
3 269-241 1 StreetElbow
4 S27-328 1 1/2"BallValvewithNut
4.1 110-248 1 Nut 316 Stainless Steel
5 S08-336 1 Handle Assembly
6 269-167 1 Tailpiece
7 114-051 1 SafetySign
8 204-421 1 EmergencyTag
9 142-002DA 1 Washer
10 153-372R 1 Adapter
For proper handle and ball valve kits,
refer to instruction sheet 215-1774.
Prepack S45-2285 includes Items 1.4, 1.6, 1.7, 1.8
Prepack S05-127 includes Items 1.11, 1.12, 1.13, 1.14
Prepack S30-109 includes Items 4, 5, 9, 10