Bradley S96-085 User manual

P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1.800.BRADLEY Fax: [phone]
bradleycorp.com
215-737 Rev. E; ECN 10-02-010
© 2011 Bradley Corporation
Page 1 of 6 1/31/2011
Bradley Multi-Station
Wall Sink
S96-085 (6951A-2) 2 station
S96-083 (6951A-3) 3 station
S96-080 (6951A-4) 4 station
S96-051 (6951A-5) 5 station
Table of Contents
Supplies Required for Installation..............2
Wall Sink Components .......................2
2-&3-Station Wall Sink Rough-Ins .............3
4-&5-Station Wall Sink Rough-Ins .............4
Installation Instructions .......................5
Cleaning Stainless Steel......................6
Installation
*FAUCETS BY OTHERS
IMPORTANT!
Read this entire installation manual to ensure proper installation. When
finished with the installation, file this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then
completely turned off before beginning installation. Debris in supply lines
can cause valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•

6951A-2 thru 6951A-5 Installation
21-31-2011 Bradley Corporation • 215-737 Rev. E; ECN 10-02-010
Supplies recommended for installation:
• 1-1/4" anchors and bolts to secure sink to wall
• Wall reinforcement (if required)
• Trap and drain pipe to 1/-1/2" O.D. tailpiece
• Supply pipe to faucets (if required)
• OPTIONAL: 1/4" anchors and bolts to secure footing to floor
WALL SINK
2-STATION (S39-375)
3-STATION (S39-374) (shown above)
4-STATION (S39-373)
5-STATION (S39-151)
1/4"-20 x 3/8"
SOCKET-HEAD
SETSCREW
(160-246)
LEG (PIPE)
(113-744)
SUPPORT BRACKET
(140-112)
2- and 3-STATION (qty. 2)
4-STATION (qty. 3)
5-STATION (qty. 4)
DRAIN SPUD
(112-028)
WASHER
(142-063)
OVAL-HEAD
SCREW
(160-042)
TAILPIECE
(S29-083) ADJUSTABLE FOOTING
(S36-020)
LOCKNUT
(161-148) STRAINER
(173-002)

Installation 6951A-2 thru 6951A-5
Bradley Corporation • 215-737 Rev. E; ECN 10-02-010 1-31-2011 3
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
2-Station Wall Sink
Dimensions
3-Station Wall Sink
Dimensions

6951A-2 thru 6951A-5 Installation
41-31-2011 Bradley Corporation • 215-737 Rev. E; ECN 10-02-010
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
4-Station Wall Sink
Dimensions
5-Station Wall Sink
Dimensions

Installation 6951A-2 thru 6951A-5
Bradley Corporation • 215-737 Rev. E; ECN 10-02-010 1-31-2011 5
1Mount sink to wall
Use a carpenter’s level to make sure that all of the brackets
are level with the floor and with each other before securing
them to the wall. An improperly installed bracket will lead to
an improperly installed sink that is not level.
To avoid leakage, use plumber’s putty to caulk the drain spud.
2Assemble Drain
1. Install suitable wall anchors for 1/4" bolts at the dimensions shown in
the rough-in drawings (anchors and bolts supplied by installer).
• 2- and 3-station sinks require 10 wall anchors and bolts.
• 4-station sink requires 12 wall anchors and bolts.
• 5-station sink requires 16 wall anchors and bolts.
2. Mount the support brackets to the wall anchors with 1/4" bolts (supplied
by installer).
• 2- and 3-station sinks require two brackets and six bolts.
• 4-station sink requires three brackets and nine bolts.
• 5-station sink requires four brackets and 12 bolts.
3. Hang the wall sink onto the support brackets.
Make the connection to the pipe (suppied by the installer) AFTER
the sink legs have been installed.
1. Insert the drain spud into the hole in the wall sink and secure the spud to
the sink with the washer and locknut provided as shown.
2. Attach the strainer to the drain spud and secure with the two screws
provided as shown.
3. Insert the flanged plastic washer into the top of the tailpiece. Slide the
tailpiece nut up to the top of the tailpiece and screw the nut into the spud
to secure the tailpiece to the sink.

6951A-2 thru 6951A-5 Installation
61-31-2011 Bradley Corporation • 215-737 Rev. E; ECN 10-02-010
3Attach Legs and Footings
4Complete Installation
1. Screw the adjustable footings into the bottom of the legs.
2. Insert the legs into the flanges located at the underside of the sink. Secure the
legs to the sink with the setscrews provided.
3. Adjust the foot pads on the bottom of the legs to level the unit and provide proper
drainage.
1. Secure the sink to the wall with four 1/4" bolts (supplied by installer) through the
wall anchors installed in Procedure #1.
2. OPTIONAL FAUCETS: Make the proper supply connections to the faucets
as outlined in the faucet manufacturer’s installation manual (pipe supplied by
installer).
3. Make the drain connection to the 1-1/2" O.D. tailpiece on the sink (pipe supplied
by installer).
Cleanliness is of utmost importance. Do not permit salty solutions to evaporate and dry on stainless steel. Never use
ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or stainless steel brushes.
1. Remove ordinary deposits of dirt and grease with soap and water. Whenever possible, the metal should be thoroughly rinsed
and dried after washing.
2. Use stainless steel polishing powder to get rid of tightly adhering deposits.
3. Look for the source of the rust in some iron or steel not actually a part of the stainless steel structure. Sometimes the
appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Asteel nail or screw may be
the cause of the trouble.
4. If the sprayhead delivers an uneven spray, remove the sprayhead from the unit, disassemble, and remove foreign matter.
Reassemble sprayhead and reinstall into unit.
Cleaning Stainless Steel