Bradley S19-230H User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Installation
215-160H Rev. D; EN 06-532E
© 2007 Bradley Corporation
Page 1 of 4 4/24/07
S19-230H
Freestanding Eyewash
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . .3
Assembly of Components . . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2
S19-230H Installation
4/24/07 Bradley Corporation • 215-160H Rev. D; EN 06-532E
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
!
!
!
!
P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

3
Installation S19-230H
Bradley Corporation • 215-160H Rev. D; EN 06-532E 4/24/07
Installation
NOTE: Flush the water supply line before
beginning installation.
Supplies Required:
• Pipe sealant
• Piping to 1/2" IPS water supply inlet
Piping to 1-1/4" drain outlet
• Sign-mounting hardware
Step 1: Assemble eyewash
components
NOTE: Top of eyewash heads should be 33"-
45" (838mm-1142mm) from floor.
1. Assemble eyewash components as shown
in Figure 2 on page 4.
• Apply pipe sealant (supplied by
installer) to all male-threaded pipe
joints.
• Use a strap wrench around pipes when
tightening to prevent marring.
Step 2: Connect water supply
1. Connect the assembled eyewash to the 1/2" IPS inlet supply and 1-1/4 - IPS the tailpiece drain
(see Figure 2).
2. Mount the safety sign to a wall or pipe using sign-mounting hardware (supplied by installer).
3. Open the water supply lines. Test for leaks and adequate water flow.
Ø 10"
(254mm)
3-3/4"
(95mm)
7-3/8"
(187mm)
5-1/4"
(133mm)
7-1/2"
(191mm)
15-1/2"
(394mm)
36"
(914mm)
Suggested
Height
To Floor
30-1/2"
(775mm)
Suggested
Height
To Floor
Figure 1

Assembly of Components and Parts List
4
S19-230H Installation
4/24/07 Bradley Corporation • 215-160H Rev. D; EN 06-532E
1S90-304 1 Plastic Eyewash Bowl Assy.
1.1 111-039 1 Inlet Drain Fitting
1.2 124-028 1 Gasket
1.3 154-058 1 Plastic Bowl
1.4 173-025 1 Cup Strainer
1.5 S21-073 1 Supply Stem
1.6 113-1185 1 Spacer, Drain
1.7 S05-100 1 Eyewash Yoke
1.8 107-371 2 Dust Cover
1.9 269-651 1 Swivel Stem
1.10 124-055 2 Quad Ring
1.11 139-087 1 Spray Ring Assembly
1.12 110-199 1 Acorn Nut
2 113-006LQ 1 1/2" NPT Pipe
3 169-025 1 Elbow
4 S27-282 1 1/2” Ball Valve with Nut
4.1 110-215 1 Nut Only
5 128-135 1 Handle, Plastic
6 142-002DA 1 Lockwwasher
7 269-167 1 Tailpiece
8 114-051 1 Safety Sign
9 204-421 1 Emergency Tag
Item Part No. Qty Description Item Part No. Qty Description
P.O.Box 309, Menomonee Falls, WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
1.1
1.2
1.3
1.4
1.5
1.6
1.9
1.8
1.10 1.11
1.12
2
34
5
6
7
8
9
1.7
1
4.1
NOTE: Items 1.1–1.12 come presasembled as Item 1.
Figure 2
Prepack S45-122 includes Items 4, 4.1, 5, 6,
Prepack S45-123 includes Items 4.1, 5, 6
Prepack S05-127 includes Items 1.9, 1.10, 1.11, 1.12
Prepack S45-2284 includes Items 1.2, 1.4, 1.5, 1.6