Braun ThermoScan Use and care manual

Calibration/verification of the Braun
ThermoScan device
A Welch Allyn authorized service center must perform individual module calibration and verification
activities.
NOTE: The tests are product specific.
Welch Allyn service test equipment and training is available. Contact Welch Allyn Customer
Service for information.
Braun ThermoScan display and error codes
Display Definition/Description Required action
Display indicates normal operation
after reading is taken. None.
Display indicates normal operation
after device is turned off.
None.
Turn device on.
Display indicates reading stored in
memory.
None.
See manufacturer's instruction
guide.
Setting used to change the default
temperature scale. See manufacturer's instruction guide.
Calibration mode. See manufacturer's instruction
guide.
Setting displays hours remaining
before anti-theft function of the device
is enabled and device is locked.
None.
See manufacturer's instruction
guide.
Anti-theft function of the device is
enabled; device is locked.
Return device to station for
unlocking.
See manufacturer's instruction
Page 1 of 5Calibration/verification
9/28/2010file://C:\Documents and Settin
g
s\
g
rahamw1\Local Settin
g
s\Tem
p
\~hhD427.htm

guide.
Battery is low, but thermometer will
still operate correctly. Insert new batteries.
Battery is too low to take correct
temperature measurements. Insert new batteries.
Anti-theft function of the device is
enabled; device is locked. Batteries are
low.
Return device to station for
unlocking.
Insert new batteries.
See manufacturer's instruction
guide.
No probe cover is attached. Attach new, clean probe cover.
No probe cover is attached and
batteries are low.
Attach new, clean probe cover.
Insert new batteries.
Position error.
Clear the display by pushing
the Start button once.
Ensure that the position of the
probe is correct and remains
stable.
Ambient temperature is not within the
allowed operating range of 50 - 104 °F
(10 - 40 °C) or is changing too rapidly.
Allow the thermometer to
remain in a room where the
temperature is 50 - 104° F (10 -
40° C) for 30 minutes.
Temperature taken is not within
typical human temperature range.
HI will be displayed when temperature
is higher than 108 °F (42.2 °C).
LO will be displayed when
temperature is lower than 68 °F (20 °
Ensure that the probe tips and
lens are clean and a new, clean
probe cover is attached. Ensure
that the thermometer is
properly inserted into the ear
canal.
Page 2 of 5Calibration/verification
9/28/2010file://C:\Documents and Settin
g
s\
g
rahamw1\Local Settin
g
s\Tem
p
\~hhD427.htm

Setup
Connect the Braun ThermoScan module to perform the verification process.
Test equipment part numbers
Use the equipment detailed in the table below for the Braun ThermoScan verification. Contact Welch
Allyn customer service to purchase or locate specific parts.
Setup
C. Retake measurement.
System error.
Wait one minute while the
thermometer turns off.
Turn thermometer on again.
If error persists, reset the
thermometer by removing, then
replacing the batteries.
Contact Welch Allyn customer
service.
Part number Description Quantity
01802-110 Tester, Calibration, 9600 Plus (North America,
EMEA) 1
01802-119 Tester, Calibration, 9600 Plus (Latin America,
Asia Pacific) 1
01802-220 Tester, Calibration, 9600 Plus (UK) 1
4500-925 USB 2.0/5-pin Mini-B cable, gold, 6 feet 1
715701 VSM6000 service test box 1
Page 3 of 5Calibration/verification
9/28/2010file://C:\Documents and Settin
g
s\
g
rahamw1\Local Settin
g
s\Tem
p
\~hhD427.htm

Verify
1. Click within the module row, and click Verify to activate the test sequence for the module.
2. Enter information about any replacement parts you used during service of the product. After
entering the part information, click Begin to start the tests.
3. Follow the onscreen prompts in the right side pane of the test window to progress through the test
sequence. The left detail pane shows the order of the required tests and tracks the test sequence
progress.
As the Welch Allyn Service Tool application completes each test, the pass/fail indicator changes
to green for pass or red for fail, and the application proceeds to the next test.
To terminate the active test sequence at any time, click Abort. To terminate all tests, click Abort
All.
Page 4 of 5Calibration/verification
9/28/2010file://C:\Documents and Settin
g
s\
g
rahamw1\Local Settin
g
s\Tem
p
\~hhD427.htm

After the Welch Allyn Service Tool application completes all the tests, it displays the pass/fail test
results. After
y
ou have finished reviewin
g
the test results, click Close.
Page 5 of 5Calibration/verification
9/28/2010file://C:\Documents and Settin
g
s\
g
rahamw1\Local Settin
g
s\Tem
p
\~hhD427.htm