BraunAbility HAL2 User manual

HAND ACTUATED
LOCKABLES
User Manual
EN Instructions for tting and use

2HAL2, HAL3
Thank you for choosing
Hand Actuated Lockables
from BraunAbility!
The following manual is an important part of the product, providing
you with information on how to achieve maximum performance
and safe operation. Keep the manual in a safe place so that you can
refer to it when necessary.
If you have any questions about your equipment, please contact us.
Once again, thank you for placing your condence in our products!
Safe vehicle adaptation solutions
For your safety BraunAbility products are
designed and tested according to current
directives and standards.

Safety information
Fit and use
After care
Limitation of use
Fitting the Hand Actuated Lockable (HAL) to the seat leg
Adjusting HAL setting to the rail
Operating HAL
Equipment storage and maintenance
Warranty
4
6
8
10
12
12
3
HAL2, HAL3
EN
Index
“Declaration of conformity” at the end of the manual.

Limitation of use
Safety information
4HAL2, HAL3

HAL2 - 2 Fixing Studs HAL3 - 3 Fixing Studs
5
HAL2, HAL3
EN
Fit and use

Fitting the Hand Actuated Lockable (HAL) to the seat leg
Fit and use
1. First, remove all M10 nyloc nuts and washers from sliding stud assemblies with a 17mm wrench (Fig. 1).
2. Ensure the seat is placed facing towards the front of the vehicle. Fit sliding studs through the seat leg bracket
holes as shown above. Position both seat legs at approximately 5mm (1/4”) from the front of the handle, ensuring
alignment (Fig. 2).
3. Replace all washers and nuts and loosely fasten with a 17mm wrench (Fig. 3). Finally tighten the M10 nyloc nuts with
a torque wrench to a recommended torque of : 35-40Nm (18-22lb.ft)
Note: Two removable seat xtures are normally required for each seat. It is important
that the seat legs are set to the identical rail width where the seat is to be tted.
Both HAL need to be aligned parallel to each other in the rail.
6HAL2, HAL3

WARNING
In 3 stud version, the rear most xing MUST NOT be used in isolation.
If it is intended that the seat should face the rear, please contact BraunAbility.
M10 Nyloc Nut
17mm wrench
M10 Nyloc Nut
17mm wrench
Sliding Stud
Seat Leg
Front of Vehicle
Figure 1 Figure 2 Figure 3
7
HAL2, HAL3
EN
Fit and use

Adjusting HAL setting to the rail
Fit and use
HAL lockable comes with variable adjustable setting to accommodate different rail proles and
thicknesses. Each setting relates to a different thickness depth.
Setting 1: Thinner Rail Setting 2: Standard Rail Setting 3: Thicker Rail
1. Once HAL has been tted to the seat leg, check that the lockables are on the right setting to
t the rail in your vehicle.
2. Place the seat in the rail with HAL unlocked (Fig. 4).
3. Try and lock the seat by pushing the handle forward to the locked position (Fig. 5):
A. The handle locks smoothly and the seat doesn’t rattle; HAL is set correctly.
B. The handle is difcult to push forward; looking from the front, adjust HAL by inserting a
3mm allen key and rotating half turn clockwise . Once this is done try locking HAL again.
(Repeat operation as necessary).
C. The handle locks too easily and rattles; looking from the front, adjust HAL by inserting a
3mm allen key and rotating half turn anti-clockwise. Once this is done try locking HAL again.
(Repeat operation as necessary).
IMPORTANT: Tighten by hand only. Do not use tools of any kind.
8HAL2, HAL3

Setting
Adjustment
Unlock Lock
Figure 4 Figure 5
9
HAL2, HAL3
EN
Fit and use

Operating HAL
Fit and use
1. Before locating the seat into the rail, unlock HAL, by pressing the silver trigger
(Fig 6) and then pull the handle fully back (Fig 7).
2. To locate the seat in the rail, align both HAL wheels into the rail, tilt the seat
backwards slightly and wheel it along the rail to the right location. Once this is
found, lower the seat into the rail gently push it forwards or backwards until it
is located into the rail.
3. To lock the seat into the rail, push the handle forward to the upright position
(Fig 8) until you hear it click.
Anti-tamper device
The anti-tamper device, which is supplied with HAL, is an optional accessory.
1. Should you choose to use this device during transportation, just clip it on to
the silver trigger, making sure it is safely tted (Fig 9).
2. To remove the device, simply push it sideways to release the silver trigger.
Stow away securely.
Removing seat from rail
1. To release the seat from the rail,
unlock HAL, by pushing handle
forward while pressing the silver
trigger (Fig 6), then pulling the
handle fully back (Fig 7).
2. Tip the seat backwards and
remove from the rail.
10 HAL2, HAL3

Anti-damper
device
Silver
Trigger
Figure 6 Figure 7
Figure 9
Figure 8
11
HAL2, HAL3
EN
Fit and use

Equipment storage and maintenance
After care
Regularly inspect HAL for damage, wear or malfunction. If any problems are identied replace it
immediately.
Warranty
BraunAbility products are extensively tested using BraunAbility anchorage systems, and our full warranty
normally only applies to BraunAbility equipment when used with BraunAbility branded anchorages or as
instructed.
BraunAbility have also participated in test programs with other manufacturers anchorage products and will
support warranty on the BraunAbility products when used in conjunction with such jointly tested systems.
For further details on specic applications please contact the Sales Ofce. In other situations, using
BraunAbility products, for which BraunAbility has not participated in a joint test program, a limited
BraunAbility warranty will apply.
12 HAL2, HAL3

Declaration of conformity
Conforms to following directives
standards and regulations /
2001/85/EC Annexe VII Paragraphs 3.8.2.8 & 3.8.2.9
76/115/EEC
R.14.07
R.107.06
BS EN 1789:2007+A2:2014
BraunAbility, Martock, 23rd April 2019
Rob Butcher
Director of Engineering
Manufacturer /
BraunAbility UK Ltd.
Unwin House
The Horseshoe Coat Road
Martock, Somerset, TA12 6EY
UK
Phone: [phone]
E-mail: [e-mail]
www.braunability.eu
Declares that the products /
HAL2, HAL3

Accredited by URS as testing laboratory in accordance with ISO/IEC 17025:2005
Quality system certied in accordance with ISO 9001:2008
Illustrations, descriptions and specications in the user manual are based on current product information.
BraunAbility UK Ltd reserves the right to make alterations without previous notice.
© 2019 BraunAbility UK Ltd
Accredited by URS as testing laboratory in accordance with ISO/IEC 17025:2005
Quality system certied in accordance with ISO 9001:2008
Illustrations, descriptions and specications in the user manual are based on current product information.
BraunAbility UK Ltd reserves the right to make alterations without previous notice.
© 2019 BraunAbility UK Ltd

BraunAbility UK Ltd
Unwin House
The Horseshoe, Coat Road
Martock, Somerset, TA12 6EY
UK
Phone: [phone]
E-mail: [e-mail]
www.braunability.eu
UI1911F
BraunAbility UK Ltd
Unwin House
The Horseshoe, Coat Road
Martock, Somerset, TA12 6EY
UK
Phone: [phone]
E-mail: [e-mail]
www.braunability.eu