brennenstuhl SOL 04 PLUS User manual

6
Installations- and Operating Instructions
Solar LED wall lamp SOL 04 PLUS
Introduction
The lamp works with a built-in motion detector that constant scans for heat sources
moving in its monitoring area. As soon as a heat source (such as a person or a car) is
detected in this area, the light comes on and remains on as long as the heat source moves
in the monitored area.
INSTALLATION TIPS
• The lamp should ideally be installed at a height of 1.8 to 2.5 metres to cover the maxi-
mum monitored area (see Fig. 1A).
• To avoid false alarms, the light should be installed away from heat sources such as air
conditioners, other outside lights, running cars, exhaust vents, and strong sources of
electromagnetic disturbance.
• Do not aim the sensor at reflective surfaces such as smooth, white walls, swimming
pools, etc.
• The motion detector’s monitored area (about 7 metres at 100° monitoring field) can
change somewhat depending on the height at which it is installed and the installation
site. The monitored area can also change due to ambient temperature.
• Before you choose an installation site, please note that the motion detector reacts with
greater sensitivity to movement across the monitored area than movements directly to
ward or away from the sensor (see Fig. 1B).
100°
1A
100°
1,8-2,5 m
Solar module
Motion detector
015209 S lar-Wandleuchte SOL 04_015209 S lar-Wandleuchte SOL 04 BA 11.12.12 09:20 Seite 6

7
Solar LED-Wall Light SOL 04 PLUS
good detection poor detection
• Mount the lamp such that the solar module receives the maximum possible DIRECT
SUN IGHT during the day.
INSTALLATION STEPS
1. Remove the light’s mounting plate by opening the locking mechanism using the en-
closed key and turning it toward „OPEN“.
2.Drill two holes in the wall on which you wish to install the lamp and mount the mounting
plate with the screws (see Fig. 2).
3. Mount the lamp on the mounting plate and secure it by turning the key to „ OCK“. Re-
move the key and keep it for future use.
OPERATION
1. The rechargeable batteries inside are charged by the solar module. The longer the solar
module is exposed to direct sunlight during theday, the longer the light can remain on.
Before starting to use the light, the batteries should be charged in sunlight for at least 3
to 4 days (slider switch set to OFF). Alternately, the batteries can be charged with a
standard battery charger.
2.After the batteries are charged, the lamp can be used. The following operational modes
can be set on the slider switch on the back of the housing.
1B
2
015209 S lar-Wandleuchte SOL 04_015209 S lar-Wandleuchte SOL 04 BA 11.12.12 09:20 Seite 7

8
Solar LED-Wall Light SOL 04
AUTO: Normal operation through the integrated motion detector
ON: Constant light(e.g. as emergency light)
OFF: Deactivation for storage and for charging
FUNCTION
1. When the lgiht is turned on for the first time, the EDs light up and the motion detector
begins to warm up. The EDs will stay on for around 40 seconds and then blink 3 times
and switch into operational mode.
2.The light is equipped with a dimmer switch, i.e. the light switches into „AUTO“ mode
when it gets dark. The EDs activate when movement is detected in the monitored area
and stay on around 60 seconds after the last movement. If motion is detected when the
light is already on, the lighting period begins again and the EDs stay on for another
60 seconds.
3. In daylight or in bright surroundings, the light is not activated by motion.
REPLACING THE RECHARGEABLE BATTERIES
1. Set the switch to the OFF-position.
2. Remove the screws from the battery cover on the back of the light.
3. Remove the old batteries and replace them with new rechargeable AA Ni-MH 1.2 V bat-
teries. Make sure the +/- poles are correctly connected.
4. The batteries should be charged in direct sunlight for at least 3 to 4 days prior the first
use of the light (slider switch in OFF-position).
015209 S lar-Wandleuchte SOL 04_015209 S lar-Wandleuchte SOL 04 BA 11.12.12 09:20 Seite 8

9
Solar LED-Wall Light SOL 04 PLUS
TROUBLESHOOTING
Problem ight does not activate when there is movement in the monitored area.
Possible Cause Suggested Solution
1. Batteries are dead Recharge batteries
2.Nearby lights too bright. Aim the unit away from the light source
Problem ight activates for no apparent reason (false alarm).
Possible Cause Suggested Solution
1. Heat sources such as air Place the light beyond these sources
conditioners, exhaust vents,
ventilation openings, other
outdoor lights, running cars,
activate the sensor.
2. Animals, e.g. martens or house pets. Re-aiming the light can help.
3. Reflections from pool or Re-aim light
from reflecting surfaces.
NOTE: Motion detectors are more sensitive in dry and cold surroundings than in moist and
hot surroundings.
TECHNICAL DATA
Battery: 3 x AA 1,2 V / 600 mAh
Number of EDs: 2 x 0,5 W
ight duration: 60 ±2 Sec.
Monitored angle: 100°
Range: max. 7 metres
Response sensitivity: adjustable from daylight to night
Protection Class: IP44
DISPOSAL
Dispose of electronic devices in an eco-friendly fashion! Electronic devices do not
belong in your household waste. Compliant with European Guideline 2002/96/EG
for electric and electronic devices, used electronic devices must be collected
separately and taken in for environmentally sound re-cycling. Options for disposing of
used devices may be obtained from your township, city or municipal government.
Incorrect disposal of batteries rechargeable batteries can harm the environment!
Batteries and rechargeable batteries do not belong in the household waste. They
can contain poisonous heavy metals and are subject to treatment as hazardous
wastes. Take your used batteries to a municipal collection site.
015209 S lar-Wandleuchte SOL 04_015209 S lar-Wandleuchte SOL 04 BA 11.12.12 09:20 Seite 9