Brentwood Steel 6 User manual

Steel 6
Wheelbarrow Assembly

STEP 1
Place PAN (A) upside down on a flat work
surface. Insert two (2) 18 x 5 1/2"CARRIAGE
BOLTS (K) into the front slots of the pan bottom
mount and two (2) 18 x 3 1/2"CARRIAGE
BOLTS (L) into the rear slots of the pan bottom
mount. Then, insert the two (2) 18 x 3/4"STEP
BOLTS (O) into the slots located on the mount
of the front scoop.
A. Steel Pan (x1)
G. Leg (x2) H. Axle (x1)
J. Tire (x1)
I. Axle Bracket (x2)
F. Leg Brace (x1)
K. 5/16"- 18 x 5 1/2"
Carriage Bolt (x2)
Q. 1/8"- 1.25"
Cotter Pin (x2)
R. 3/4"
SAE Flat Washer (x2)
M. 5/16"- 18 x 3"
Carriage Bolt (x2)
L. 5/16"- 18 x 3 1/2"
Carriage Bolt (x6)
N. 5/16"- 18 x 3/4"
Slotted Truss Bolt (x4)
P. 5/16"- 18
Serrated Flange
Hex Nut (x16)
BL. Left Front Brace (x1) BR. Right Front Brace (x1) C. Handle (x2) D. Handle Grip (x2)
E. Nose Piece (x1)
S. Wedge (x2)
K
K
L
L
O
O
A
O. 5/16"- 18 x 3/4"
Step Bolt (x2)
YOUR KIT SHOULD INCLUDE:
TOOLS NEEDED:
Thank you for your purchase! If you have any questions or encounter any
problems with your Brentwood Wheelbarrow, feel free to call us at
1.610.374.5109 or e-mail [e-mail].
1. 1/2"or 13mm Wrench
2. Flat Head Screwdriver
3. Needle Nose Pliers
4. Safety Glasses

STEP 3
Place the two (2) LEGS (G) over the handles
and align them to the existing bolts. Secure
them by hand tightening four (4) SERRATED
FLANGE HEX NUTS (P). Hand tightening bolts
at this stage allows flexibility throughout the
assembly. Next, place the NOSE PIECE (E) on
the front of the handles with the flat side facing
forward. The portion with the holes should be
beneath the handles in its current position; this
will assure the nose piece is mounted over the
top and front sides of the handle edges when
upright. Secure the nose piece by hand
tightening two (2) 18 x 3"CARRIAGE BOLTS
(M) and two (2) SERRATED FLANGE HEX
NUTS (P).
STEP 2
Place two (2) WEDGES (S) over the BOLTS (K)
& (L) so the largest part of the wedge is facing
the front of the pan and the side with decal
faces the pan, as identified. Then, place the
two (2) HANDLES (C) over the wedges so they
are aligned with the installed bolts. NOTE: Be
sure the logos are facing upside down. Next,
slide the two (2) HAND GRIPS (D) firmly onto
the handles.
STEP 4
Take the LEFT FRONT BRACE (BL) (stamped
with an “L”) and place it over the bolt inserted
in the hole at the front of the pan. Repeat this
step for the RIGHT FRONT BRACE (BR),
(stamped with an “R”) and secure the braces to
the pan by hand tightening two (2) SERRATED
FLANGE HEX NUTS (P) to the bolts. DO NOT
attach the front braces to the handles until Step
5. Then, align the holes on the flat side of the
LEG BRACE (F) to the holes on the inside of
each leg and secure by hand tightening the
SLOTTED TRUSS BOLTS (N) and SERRATED
FLANGE HEX NUTS (P) into the four holes.
The bolt heads should face the rear of the
wheelbarrow.
HAND
TIGHTEN
BOLTS
HANDLES ARE APPLIED WITH
LOGO FACING UPSIDE DOWN
D
D
C
C
P
P
S
S
P
G
P
MAKE SURE THE 2 HOLES
LOCATED ON THE LEGS
ARE FACING THE REAR
OF THE WHEELBARROW
P
P
E
M
M
HAND
TIGHTEN
BOLTS
LEG BRACE SHOULD BE
INSTALLED SO ARCH FACES
UPWARD IN CURRENT POSITION
P
P
N
N
P
P
N
N
P
P
BR
BL

STEP 6
When constructing the wheel assembly, an
additional person may be needed to hold the
tire in place. Slide the AXLE (H) through the
mounted axle bracket. In this order, continue to
slide the axle through the first SAE FLAT
WASHER (R), the TIRE (J), the second SAE
FLAT WASHER (R), and finally, through the
second mounted axle bracket (FIG. A). Next,
insert both COTTER PINS (Q) through the
holes located on each of the axle brackets.
Bend each flange using needle nose pliers
(FIG. B). To secure the wheel assembly, push
both axle brackets inward to center the wheel
and make sure all parts are flush and aligned
together (FIG. C). Finally, firmly tighten all bolts
using a hand tool.
IMPORTANT: Once you have completed the previous steps, be sure to tighten all bolts and
fastners using a hand tool. You are now ready to enjoy your Brentwood Wheelbarrow!
WHEEL ASSEMBLY DETAIL
ASSEMBLY DETAIL
CENTER
FIG. A
FIG. A FIG. B FIG. C
FIRMLY
TIGHTEN
ALL BOLTS
I I
R R
HH
J
STEP 5
Swing the left and right front braces to align
the free ends with the remaining holes in the
handles. NOTE: Align the braces with the holes
furthest away from the pan (FIG. A). Then,
using the four (4) remaining CARRIAGE
BOLTS (L), insert each bolt from the bottom to
secure the front braces, handles, and AXLE
BRACKETS (I). Hand tighten using four (4)
SERRATED FLANGE HEX NUTS (P). The axle
brackets should allow for some flexibility at this
stage of the assembly.
HAND
TIGHTEN
BOLTS
PP
PP
I
I
L
L
L
L
JR
Q
Q
H
R