Home Styles 88 4511 95 User manual

PART LIST
HARDWARE LIST
Adjustable Pin
8 pcs. (+1 extra)
M4x25
Machine Screw
5 pcs.
A.
Top
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
E.
Back Panel
3 pcs.
D.
Middle Panel
1 pc.
H.
Back Stretcher
1 pc.
F.
Back Upright
2 pcs.
M.
Side Rack
1 pc.
N.
Side Rack
1 pc.
P.
Rack
1 pc.
O.
Base Rack
1 pc.
J.
Base
1 pc.
Caster
2 lock
2 non-lock
4 pcs.
K.
Arm
2 pcs.
Drawer
Pull Handle
5 pcs.
88 4511 95
Kitchen Cart
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
G.
Back Stretcher
1 pc.
L.
Towel Bar
1 pc.
M3x16
Wood Screw
for Leaf Support
6 pcs. (+1 extra)
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Drawer Side Part
24 pcs.(+1 extra)
M3.5x16
Wood Screw (short)
for Drawer Base Part
and Back Panel
24 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Wrench
1 pc.
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
M6x38
Head Cap Bolt (long)
4 pcs. (+1 extra)
S.
Shelf
2 pcs.
Q.
Door
1 pc.
R.
Door
1 pc.
U.
Leaf
Support
1 pc.
T.
Drawer
3 pcs.
(Please refer to the last page of these
instructions for drawer assembly steps.)
V.
Leaf
Support
1 pc.
I.
Front Piece
2 pcs.
Magnet
2 pcs.

B
C
Assembly Instructions 2/6
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Attach 2X Magnets to Top (A) by
using Wood Screws (for Magnet)
into the pre-drilled holes.
(See Figure 1)
STEP 2
Attach Arms (K) to Side Panel (B) with Head Cap Bolts. (See Figure 2)
Assemble Side Racks (M), (N), Base Rack (O) and Rack (P), then attach to Side Panel (C)
with Head Cap Bolts. (See Figure 3)
Wood Screw (for Magnet)
Magnet
Stopper
Figure 1
A
Figure 3Figure 2
N
M
P
O
Head Cap Bolt
C
K
K
Head Cap Bolt
B

Assembly Instructions 3/6
J
STEP 4
Attach 4 Casters underneath Base (J) with Head Cap Bolts (for Caster),
put 2 Casters with Lock at the front side. (See Figure 6)
Locking Caster
Non-Locking Caster Head Cap Bolt
(for Caster)
B
H
FF
EEE
G
C
Figure 6
Figure 4
Figure 5
STEP 3
Attach Back Stretcher (G) to Side Panel (B), then filp the Locks.
(See Figures 4 and 5)
Attach Back Uprights (F) and slide Back Panels (E) into position.
Attach Back Stretcher (H) and Side Panel (C) to unit, then filp the Locks.

4/6
Assembly Instructions
STEP 5
Attach base unit to
unit with Head Cap Bolts (long).
Head Cap Bolt (long)
D
I
I
G
H
L
Wood Screw
(short)
Wood Screw
(for Leaf Support)
STEP 6
Turn the unit to its’
upright position.
Slide Towel Bar (L)
into place.
Attach Front Pieces (I) and Middle Panel (D)
to unit from Step 3, then filp the Locks.
Insert Wood Screws (short) into the pre-drilled holes of Back Stretchers (G) and (H)
and tighten.
Attach Leaf Supports (U) and (V) to unit with Wood Screws (for Leaf Support) (See Figure 7).
Figure 7
U
V

5/6
Assembly Instructions
STEP 7
Insert Adjustable Pins into side panel and middle panel at the desired level.
Place Shelves (S) into position.
Attach Doors (Q) and (R) by sliding the door lift hinges into the
side panels lift hinges. (See Figure )8
Assemble Pull Handles to Doors with
Machine Screws. (See Figure 9)
Attach Top (A) to the unit, then filp the Locks.
Slide Drawers (T) into position.
Figure 8
Figure 9
A
S
S
T
T
T
Adjustable Pin
R
Q

T5.
Base Part
3 pcs.
T2.
Back Part
3 pcs.
T3.
Side Part
3 pcs.
T4.
Side Part
3 pcs.
Assembly Instructions 6/6
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
T2
T2
T2
T3
T3
T3
T4
T4
T4
T5
T5
T1
T1
T1
Drawer (T)
Part List
Figure 3
Figure 4
STEP 1
Attach T1 to T3 and T4,
using a screwdriverPhillips
and wood screws (4X),long
tighten halfway.
Attach T2 to T3 and T4 using
wood screws (4X),long
tighten halfway. (See Figure 1)
Insert wood screws (4X)short
into the pre-drilled holes in T5,
tighten screws. (See Figure 3)
Slide T5 into the grooves in T3
and T4. Be sure to push T5 all
the way forward so it meets T1.
(See Figure 2)
STEP 2
STEP 3 STEP 4
Assemble Pull Handle with
machine screws. (See Figure 4)
Tighten all screws used in drawer assembly.
T1.
Front Part
3 pcs.