Breville Toast & Melt LSG525 User manual

the Toast & Melt
TM Sandwich Press
Instruction Book - LSG525/LSG545

2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition, we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• Carefully read all instructions
before operating the sandwich
press for the first time and save
for future reference.
• Remove and safely discard
any packaging material and
promotional stickers before
using the sandwich press for
the first time.
• Do not place the sandwich
press near the edge of a bench
or table during operation.
• Ensure that the surface is level,
clean and free of water, etc.
• Keep the sandwich press clear
of walls, curtains and other heat
or steam sensitive materials.
• The sandwich press must be
used on a properly grounded
outlet. If you are not sure if
the power outlets are properly
grounded, please consult your
electrician.
• Do not, under any
circumstances, modify the
power plug or use an adapter.
• Do not place the sandwich
press on or near a hot gas or
2 Breville Recommends Safety First
6 Components
7 Functions
8 Hints & Tips
9 Care, Cleaning & Storage
Contents

3
electric burner, or where it
could touch a heated oven. Use
the sandwich press well away
from walls.
• Provide adequate space
above and on all sides around
the sandwich press for air
circulation.
• Do not place the sandwich
press on any surface that
may be affected by heat. The
use of a heat resistant matt
under the sandwich press
is recommended on these
surfaces.
• Always operate the sandwich
press on a stable and heat
resistant surface. Do not use on
a cloth-covered surface, near
curtains or other flammable
materials.
• Do not use on a sink drain
board.
• Do not touch hot surfaces. Use
the handles to lift and open the
top plate. Take care when using
the height-adjustable control.
• Do not leave the sandwich
press unattended when in use.
• Do not allow the power cord
to come in contact with the
hot cooking plates. Ensure the
power cord does not become
trapped between the cooking
plates during use and storage.
• Always keep the power cord
away from any heat source
including the accessible surfaces
of the sandwich press, and those
of other appliances nearby.
• The sandwich press is not
suitable to be used in a small
appliance enclosure. Ensure to
leave adequate space all around
the sandwich press. Minimum
space of 20cm is recommended.
• Do not place anything on top of
the sandwich press when the lid
is closed, during operation and
and when storing.
• Always switch the sandwich
press off at the power outlet,
then unplug the power cord
and allow to cool. Ensure the
unit has cooled down before
cleaning, attempting to move
the appliance, disassembling,
assembling and when storing
the appliance
• Do not use chemicals, steel
wool, metal scouring pad, harsh
abrasives, caustic cleaners
or oven cleaners to clean the
sandwich press as these can
damage the housing or the
coating of the cooking plates.
• Always remove the food from the
sandwich press with a heatproof
utensil e.g., silicone spatula or
tongs. Never use your hands.

4
• Do not use sharp objects or
utensils inside the sandwich
press as they may scratch or
damage the surface of the
cooking plates.
• The sandwich press is not
intended to be operated by
means of an external timer or
separate remote control system.
• Do not place the sandwich press
in direct sunlight. Colour fading
and discolouration may occur
when the sandwich press is
consistently exposed to UV light.
• Keep the exterior housing and
the non-stick cooking plates
clean. Follow the cleaning
instructions provided in this
book. Refer to Care, Cleaning
and Storage (Page 9).
CAUTION
• Do not touch hot surfaces. The
accessible surfaces will be hot
when the sandwich press is
operating and for some time
after use.
This appliance is marked with a
hot surface symbol.
WARNING
Fully unwind the power cord
from the cord wrap on base
before use.
IMPORTANT
SAFEGUARDS FOR
ALL ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Connect only to a 230V or
240V power outlet.
• Do not let the power cord hang
over the edge of a bench or
table, touch hot surfaces or
become knotted.
• To protect against electric shock,
do not immerse the power
cord, power plug or appliance
in water or any other liquid
or allow moisture to come in
contact with the part, unless it is
recommended in the cleaning
instructions.
• Children should be supervised
to ensure that they do not play
with the appliance.
• It is recommended to regularly
inspect the appliance. To
avoid a hazard do not use the
appliance if power cord, power
plug or appliance becomes
damaged in any way. Return the
entire appliance to the nearest
authorised Breville Service
Centre for examination and/or
repair.
• The appliance is not
intended for use by persons

5
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre.
• This appliance is for household
use only. Do not use this
appliance for anything other
than its intended use. Do not
use in moving vehicles or
boats. Do not use outdoors.
Misuse may cause injury.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current
not exceeding 30mA be
installed in the electrical circuit
supplying the appliance. See
your electrician for professional
advice.
• During electrical storms,
the appliance should be
disconnected from the power
source at the wall socket to
prevent any electrical surges
that may arise during the storm
and which may inadvertently
cause damage to the appliance
and its electronic componentry.
• Always turn the appliance to
the off position by switching
off at the power outlet and
unplugging from the power
outlet
• Before cleaning, always turn the
appliance to the off position,
switch off at the power outlet,
unplug at the power outlet
and remove the power cord, if
detachable, from the appliance
and allow all parts to cool.
• Do not place this appliance on
or near a heat source, such as
hot plate, oven or heaters.
• Position the appliance at a
minimum distance of 20cm
away from walls, curtains and
other heat or steam sensitive
materials and provide adequate
space above and on all sides for
air circulation.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS

6
Components
A. 2000W of power (LSG525)
2200W of power (LSG545)
For fast heat up and quick and even
toasting.
B. Heavy-duty stainless-steel arms
For durability and strength.
C. ‘Power’ and ‘Ready’ lights
Indicate when the sandwich press is
heating or ready to use.
D. ‘Floating hinge’ top plate
Automatically adjusts to thick or
thin sandwiches.
E. Flat, non-stick cooking plates
Premium non-stick coating for a quick
cleaning.
F. Height-adjustable control with 4 settings
(LSG525) or 7 settings (LSG545)
To accommodate open sandwich melts,
toasted sandwiches, artesian breads & wraps,
and everything in between.
G. Safety storage lock
To lock the plates closed for upright storage.
H. Non-slip feet with convenient cord wrap
on base.
A
C
D
F
G
B
E
H
LSG525 pictured

7
Functions
BEFORE FIRST USE
Remove any promotional materials and
packaging materials before use. Check that
the cooking plates are clean and free of dust.
If necessary, wipe over the plates with a damp
cloth.
HEIGHT-ADJUSTABLE CONTROL
Your sandwich press features a height-
adjustable control located on right-side arm
which allows the top plate to sit one of the
4 (LSG525) or 7 (LSG545) different height
positions above the bottom plate. This allows
your sandwich press to be used to toast a variety
of bread sizes and thicknesses, and also works
for open sandwich melts (see Fig 1).
Fig 1
TOASTED SANDWICH
1. Move the locking clip from the LOCK to
OPEN position, but leave the lid closed.
2. Insert the power plug into a 230V or 240V
power outlet and then turn the power ON.
The orange ‘POWER’ light will illuminate.
3. Allow the sandwich press to pre-heat with
the top cooking plate in the closed position
until the green ‘READY’ light illuminates.
4. Whilst the sandwich press is pre-heating
prepare the sandwich. When the sandwich
press has pre-heated, the 'READY' light
will illuminate. Open the top plate and
place using the handle the sandwich onto
the bottom cooking plate. Always place
sandwiches towards the rear of the bottom
cooking plate.
5. Adjust the height-adjustable control to the
setting of choice for the sandwich being
toasted. Close the top cooking plate using
the handle. Do not press down. The top
cooking plate has a floating hinge that
is designed to evenly press down on the
sandwich (see Fig 2).
Fig 2
6. Toasting should take approximately
3-5minutes. Exact toasting time will be a
matter of personal taste. It will also depend
on the type of bread and filling used.
7. When the sandwich is cooked, use the
handle to raise the top cooking plate.
Remove the sandwich with the help of a
plastic, silicone or wooden spatula. Never
use metal tongs or a knife as these can
cause damage to the non-stick coating.
8. When finished using, turn the sandwich
press off at the power outlet and allow
to cool before cleaning. See cleaning
instructions found in this book.

8
NOTE
• Always allow the sandwich press to pre-heat
until the green ‘READY’ light illuminates.
• The safety storage lock should not be used to
clamp down the top cooking plate when the
sandwiches are in the sandwich press. The
weight of the top cooking plate will gradually
press down the sandwich during the cooking
process.
• When using the sandwich press for the
first time you may notice a fine smoke haze.
This is caused by the heating of some of the
components. There is no need for concern.
WARNING
HOT SURFACE - The accessible surfaces
will be hot when the sandwich press
is operating and for some time after use.
NOTE
Fully unwind the cord from the cord wrap on the
base before use.
OPEN MELT SANDWICH
1. Unlock the sandwich press and turn on at the
power outlet. Allow the sandwich press to
pre-heat until the green ‘READY’ light
illuminates.
2. Open the top plate using the handle and
place the open sandwich with topping to be
melted on the bottom plate.
3. Move the height-adjustable control to a
higher height whereby the top plate sits
above, but not touching the sandwich.
4. Slowly lower the top plate until it rests on the
height-adjustable control.
5. The top plate will radiate the heat to melt
ingredients for the open melt, such as cheese.
6. Toasting melts should take approximately
6-8minutes, however, exact toasting time will
vary depending on the toppings used.
Hints & Tips
BREAD
Most types of bread can be used; white,
wholemeal, wholegrain, raisin loaf and so on.
The sandwich press is also ideal for toasting
artisan breads such as focaccia, Turkish bread,
baguettes as well as bread rolls. Raisin bread,
brioche or other sweet breads which contain a
higher sugar content will tend to brown quicker.
FILLINGS
If using fruit as a filling, try to use canned or
pre-cooked fruit as fresh fruit may produce
excessive liquid during cooking. Be careful when
biting into sandwiches that contain fillings such
as cheese and tomato or jam as they retain heat
and may cause harm if eaten too quickly.
FAT-FREE TOASTING
Due to the non-stick flat plate design, it is not
necessary to use butter or margarine on the
outside of your toasted snacks.

9
Care, Cleaning
& Storage
Before cleaning, ensure the power is switched
off and then remove the power plug from the
power outlet.
Allow your sandwich press to mostly cool before
cleaning however, the sandwich press is easier
to clean when still slightly warm.
Always clean your sandwich press after each
use to prevent a build-up of baked-on foods.
Wipe cooking plates with a soft, damp cloth to
remove food residue.
WARNING
Do not immerse any part of the Breville
sandwich press or the power cord in the
dishwasher, in water or in any other liquid.
PFOA-FREE NON-STICK COATING
Cooking on a non-stick surface minimises the
need for oil as food does not stick and cleaning
is easier. Any discolouration that may occur
will only detract from the appearance of the
sandwich press and will not affect the cooking
performance. When cleaning the non-stick
coating, do not use metal (or other abrasive)
scourers. Wash with warm soapy water and dry
thoroughly. Remove stubborn residue using a
damp cloth.
SEASON THE PLATES
Seasoning the plates occasionally, although not
necessary, may help to prevent sticking and
to make cleaning easier. To season, brush the
cooking plates with a little vegetable oil and
rub off the excess with absorbent paper. Do this
after preheating the unit.
NOTE
The cooking plates and hinges are coated with a
non-stick surface; do not use abrasive cleansers
or scourers.
WARNING
Allow the unit to cool down before attempting
to move.
STORAGE
To store your sandwich press:
1. Switch off at power outlet and unplug power
cord from the wall.
2. Allow the sandwich press to mostly or fully
cool, then clean as directed.
3. For storing, lock the cooking plates together
by sliding the height-adjustable control to
the front LOCK position (see Fig 3).
Fig 3
4. Wrap the power cord in the cord storage
area on the base (see Fig 4).
Fig 4
5. Store on a flat, dry, level surface. The
sandwich press is designed to be stored
standing on its edge for space saving.

10
NOTE
The storage lock should not be used to clamp
down the top plate when sandwiches are in the
sandwich press.
WARNING
Do not immerse any part of your sandwich
press or the power cord in water or any other
liquid.