Breville Scraper Mixer Pro User manual

www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2013.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
Model BEM800 Issue - J13
Australian Customers
Mail: PO Box 22
Botany, NSW, 2019
AUSTRALIA
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
New Zealand Customers
Mail: Private Bag 94411
Greenmount, Auckland
NEW ZEALAND
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
Breville Customer Service Center

CONGRATULATIONS
On the purchase of your new
Breville Fast Slow Cooker™
Suits all BEM800 models
the Scraper Mixer Pro
Instruction Booklet

CONGRATULATIONS
on the purchase of your new
Breville product

3
CONTENTS
4Breville recommends safety first
7Know your Breville product
11 Assembly & operation
18 Care, cleaning and storage
20 Measuring and weighing
23 Hints and tips
28 Troubleshooting
30 Recipes

4
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and
manufacture consumer products with the safety of you, our
valued customer, foremost in mind. In addition we ask that you
exercise a degree of care when using any electrical appliance
and adhere to the following precautions.
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Carefully read all
instructions before operating
the Scraper Mixer Pro for
the first time and save for
future reference.
• Remove and safely discard
any packaging material and
promotional labels before
using the bench mixer for
the first time.
• To eliminate a choking
hazard for young children,
remove and safely discard the
protective cover fitted to the
power plug of this appliance.
• Do not place the bench mixer
near the edge of a bench
or table during operation.
Ensure the surface is level,
clean and free of water and
other substances. Vibration
during operation may cause
the appliance to move.
• Do not use the bench mixer
on a sink drain board.
• Do not place the bench
mixer on or near a hot gas or
electric burner, or where it
could touch a heated oven.
• Always ensure the bench
mixer is completely
assembled before operating.
Follow the instructions
provided in this book.
• Ensure the speed control
dial is in the OFF position
and the bench mixer is
switched off at the power
outlet and the power cord
is unplugged before
attaching the beater, whisk
or dough hook.
• Do not use attachments other
than those provided with the
bench mixer. Use only the
beater whisk and dough hook
supplied with the mixer.
IMPORTANT SAFEGUARDS

5
BREVILLE RECOMMENDS SAFETY FIRST
• Do not operate the appliance
continuously on heavy loads
for more than 3 minutes.
None of the recipes in
this book are considered a
heavy load.
• Handle the bench mixer and
attachments with care. Never
place your fingers inside
the mixing bowl or near the
beater, whisk or dough hook
during operation.
• Keep hands, hair, clothing,
as well as, spatulas and other
utensils away from moving
beater, whisk or dough hook/
during operation.
• Should an object such as a
spoon or spatula fall into
the bowl while mixing,
immediately ensure the
speed control dial is in the
OFF position, turn the bench
mixer off, unplug at the power
outlet and remove the object.
• Do not place hands in the
mixing bowl unless the bench
mixer is disconnected from
the power outlet. Ensure the
speed control dial is in the
OFF position, the bench
mixer is switched off and
unplugged from the power
outlet before removing the
beater, whisk or dough hook.
• Ensure the motor and beater,
whisk or dough hook have
completely stopped before
disassembling.
• Always remove the beater,
whisk or dough hook
from the bench mixer
before cleaning.
• Care should be taken when
removing the food from
the mixer bowl by ensuring
the motor and the beater,
whisk, or dough hook have
completely stopped before
disassembling. Ensure the
speed control dial is in the
OFF position, the appliance
is switched off at the power
outlet and unplugged before
unlocking the mixer motor
head and moving into the
upright position. The beater,
whisk or dough hook should
be released from the mixer
motor head before removing
the processed food from the
mixer bowl and the beater,
whisk or dough hook.
• Ensure the mixer motor head
is locked into the horizontal
(closed) position when not in
use and before storing.

6
BREVILLE RECOMMENDS SAFETY FIRST
• Always ensure the speed
control dial is in the OFF
position, the power is
switched off at the power
outlet and the power cord is
unplugged from the power
outlet before attempting to
move the bench mixer, before
assembling or disassembling,
when not in use and before
cleaning or storing.
• Do not move the bench mixer
whilst in operation.
• Do not leave the bench mixer
unattended when in use.
• Do not place any part of
the bench mixer in the
dishwasher other than the
bowl, splash guard, beater,
dough hook and whisk.
• Do not place any part of
the bench mixer in the
microwave oven.
• Keep the bench mixer
clean. Follow the cleaning
instructions provided in
this book.
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Do not let the power cord
hang over the edge of a
bench or table, touch hot
surfaces or become knotted.
• To protect against electric
shock do not immerse the
power cord, power plug or
appliance in water or any
other liquid.
• The appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• Children should be
supervised to ensure
that they do not play with
the appliance.
SAVE THESE
INSTRUCTIONS

7
BREVILLE RECOMMENDS SAFETY FIRST
• It is recommended to
regularly inspect the
appliance. To avoid a hazard
do not use the appliance if
power cord, power plug or
appliance becomes damaged
in any way. Return the entire
appliance to the nearest
authorised Breville Service
Centre for examination and/
or repair.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre.
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors. Misuse
may cause injury.
• This appliance shall not be
used by children.
• Keep the appliance and its
cord out of reach of children.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current not
exceeding 30mA be installed
in the electrical circuit
supplying the appliance.
See your electrician for
professional advice.
WARNING
Ensure the speed dial control
is in the OFF position the
bench mixer is switched
off at the power outlet and
unplugged from the power
outlet before attaching the
beater, whisk or dough hook.

KNOW
your Breville product

9
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
A
H
K
E
B
D
C
G
F
J
A. Motor head - Powerful motor for
thorough mixing results.
B. 4.7L stainless steel mixing bowl
with handle.
C. Illuminated LED speed indicator band-
Displays selected mixing task.
D. Tilt back and lock down hinge button -
The motor head tilts back and locks into
position to allow easy removal of the
mixing bowl and attachments.
E. Bowl locking recess - The bowl locking
recess allows the bowl to be securely
locked into place for safety and stability
when the mixer is in operation.
F. LCD screen with count up & down
timer - Mixer can be set to count down
according to a specified time on a recipe
or set to count up to assess mixing time.
G. Pause function - Rotate dial to PAUSE
to temporarily stop mixing and pause
the timer.
H. Breville Assist™ handles - Handles on
base and on motor head allow for easy
and comfortable lifting of the mixer.
I. Load sensing technology - Mixer
automatically senses the load and
adjusts the power to maintain the
selected speed (not shown).
J. Internal cord storage - Located in
the rear of the mixer. Cord pushes into
the mixer base for convenient and
tidy storage.
K. Splash guard - Prevents ingredients
from splattering out of the bowl.
H

10
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
L. Flat beater - Thoroughly mixes a variety
of mixtures such as cake and biscuit
batter, pastries, and mashed potatoes.
M. Wire whisk - Consistently mixes
and aerates for egg whites, cream
and thin batters.
N. Dough hook - Effectively kneads heavy
dough for bread and pizza.
O. Scraper beater - Scrapes the sides and
bottom of the bowl for exceptionally
thorough mixing, of cake and biscuit
batter, pastry and frosting.
P. Spatula (not shown).
ABOUT YOUR SCRAPER BEATER
The Breville scraper beater folds ingredients
and continuously scrapes down the sides and
bottom of the bowl for exceptionally thorough
mixing. It virtually eliminates the need to
scrape the bowl by hand with a spatula and
cuts mixing time up to 60%.
Under-mixed batters produce poorly baked
results, resulting in collapsing, unevenness of
crumb, holes, low rising, streaking and course
textures. The scraper beater will help to ensure
a thoroughly mixed batter for your favourite
cakes, biscuits, frosting and more.
L
N
M
O

ASSEMBLY & OPERATION
of your Breville product

12
PAge heAder.....
ASSEMBLY & OPERATION
ASSEMBLING THE MIXER
Before using your Breville Scraper Mixer
Pro for the first time, remove any packaging
material and promotional labels. Ensure the
speed control dial is in the OFF position, the
mixer is switched off at the power outlet and
the power cord is unplugged.
Remove the mixing bowl, beater, whisk and
dough hook and wash in warm soapy water
with a soft cloth. Rinse and dry thoroughly.
The bowl and the attachments may be
washed in the dishwasher.
NOTE
When first using your Breville Scraper
Mixer Pro, you may notice an odour
coming from the motor. This is normal
and will dissipate with use.
ATTACHING THE BOWL
1. Place the mixer base on a level, dry
surface such as a bench top. The mixer
motor head should be in the horizontal
(closed) position. Raise the mixer
motor head by pressing the
RELEASE button.
2. Lift the mixer motor head up until it tilts
back and locks into the open position.
3. Insert the mixing bowl into the bowl
locking recess of the mixer stand and
turn clockwise until the bowl locks
securely into place.
NOTE
To remove or insert the mixing bowl,
the mixer motor head must be raised
and locked into the open position.

13
PAge heAder.....
ASSEMBLY & OPERATION
ATTACHING THE SCRAPER BEATER,
FLAT BEATER, DOUGH HOOK OR
WHISK TO THE MIXER MOTOR HEAD
1. Ensure the mixer motor head is in the
raised/open position. Align the groove
in the top of the mixing attachment with
the locking pin on the spindle extending
down from the mixer motor head.
2. Push the attachment upwards and turn
clockwise until it locks securely onto the
locking pin on the spindle (see Fig. 1).
Fig. 1
3. Lower the mixer motor head by pressing
the RELEASE button and gently pushing
the mixer motor head down until it locks
into the horizontal (closed) position
(see Fig. 2).
Fig. 2
4. The splash guard can now be assembled
if required. Slide the main ring into
position on top of bowl, then assemble
the pour spout.
NOTE
When ingredients are in the mixing
bowl, the scraper beater may make a
slight noise as it scrapes the sides and
bottom of the bowl. This is normal and
should not cause concern.
Do not turn the mixer on with the
scraper beater in place if the mixing
bowl is empty. This will cause the
scraper beater to make a loud noise as
it scrapes the bowl.
OPERATING THE MIXER
Planetary Mixing Action
By replicating a similar mixing action used
by commercial mixers in bakeries and
patisseries, the Scraper Mixer Pro head
rotates around the bowl whilst rotating
the beater in the opposite direction. This
ensures a superior and thorough mixing
result without the need for a rotating bowl.
1. Ensure the speed control dial is set to
the OFF position, plug the cord into
a 220-240V power outlet and switch
the power ON at the power outlet. The
illuminated LED speed indicator band
will flash and the count up/down timer
will display 0:00. The mixer is now
ready to be used.

14
PAge heAder.....
ASSEMBLY & OPERATION
NOTE
If the mixer has not been used for
3 minutes it will automatically change
from STANDBY mode to a power
saving OFF mode and the illuminated
LED will switch off. To exit OFF mode
and begin mixing, turn the dial to the
selected speed or press one of the
count up/down timer buttons.
2. Add ingredients to the mixing bowl as
indicated in the recipe.
Always begin mixing by selecting a low
speed setting on the speed control dial.
Starting on a low speed will prevent
ingredients splattering. Increase the
speed as suited to the mixing task. The
speed setting can be adjusted during
operation by moving the dial clockwise
for the main mixing settings. Use the
mixing guide in this booklet as
a reference.
If necessary, stop the mixer during
operation and scrape any food mixture
down the sides of the mixing bowl with
a spatula.
NOTE
Always turn the mixer off if you
need to scrape the bowl during use,
and then switch back on and
continue mixing.
THE COUNT-UP TIMER
The count-up timer is especially useful
to gauge mixing time. You can monitor
the time it takes to thoroughly mix the
ingredients, so that the next time you mix
the same ingredients you can set the count-
down timer for the specific time.
The count-up timer will automatically
begin counting up as soon as the dial is
rotated from OFF to one of the speeds.
When the dial is turned to PAUSE the total
time will be displayed on the LCD and will
flash. When the dial is turned to OFF, the
LCD display will reset back to 0:00.

15
PAge heAder.....
ASSEMBLY & OPERATION
THE COUNT-DOWN TIMER
The count-down timer is especially useful
for any recipe that specifies the length
of time ingredients should be mixed.
For example, if a recipe reads, “beat for 3
minutes,” you can set the count-down timer
to 3 minutes by pressing the up/down
arrows. After 3 minutes of mixing, an alarm
will sound and the motor will automatically
turn off. The count-down timer will flash
OFF. The control dial must to be rotated to
the OFF position to reset the timer and to
continue mixing.
To set the count down timer, press the up or
down arrows until the desired mixing time is
displayed on the LCD screen.
NOTE
Press and hold the arrows down to
scroll through the timer setting
more quickly.
Rotate the dial clockwise to select the
desired speed and to begin mixing. When
the timer has finished counting down,
0:00 will flash on the LCD screen and a
beep will sound to notify you that the time
has expired. The mixer will automatically
turn the motor off. The control dial must
be rotated to the OFF position to reset the
timer and to continue mixing.
NOTE
The maximum time displayed on the
timer is 60 minutes. The mixer will
automatically switch OFF at
60 minutes. The control dial needs to
be rotated to the OFF position to reset
the timer and to continue mixing.
PAUSE MODE
While mixing, at any stage, you can rotate
the control dial to the PAUSE setting. This
will turn the motor off and pause the timer.
This enables you to assess the mixing
progress or add additional ingredients
without affecting the timer.
For example, if you are mixing using the
count-up timer mode, you can rotate the
control dial from one of the mixing speeds
to PAUSE. The mixer motor will stop and the
timer will pause. Once ready, you can rotate
the dial back to one of the mixing speeds,
the timer will continue to count-up from
the exact time it was paused. Alternatively,
if you have turned the mixer to PAUSE you
can then reset the timer to 0:00 by rotating
the dial to OFF position.
If using the PAUSE function in count-
down timer mode, you can suspend the
timer at any stage during the count-down
process by rotating the control dial to the
PAUSE setting. To continue mixing in the
count-down timer mode, simply rotate the
dial back into one of the mixing speeds or
alternatively to the OFF position to reset the
timer to 0:00.

16
PAge heAder.....
ASSEMBLY & OPERATION
MOTOR HEAD SAFETY CUT-OFF
The mixer is equipped with a motor head
safety cut-off. If the mixer head is lifted up at
any time while the mixer motor is switched
on, the safety cut-off will automatically
switch the motor off and set the mixer into
standby mode.
To restart the motor, lower the mixer head
into the secured position, turn the speed
control dial away and back to previous
speed setting to resume mixing and time
recording if mixer head is lower down within
5 minutes.
If the mixer head is not lower down for 5
minutes or more, to restart the motor, turn
the dial to off first, then dial to required
speed setting. Time recording will start
from 0.
To turn the mixer off, turn the dial to the
OFF position and unplug the appliance.
ELECTRONIC PROTECTION
CUT-OFF - CURRENT OVERLOAD
The mixer is equipped with an electric
protection cut-off and will automatically
stop operating if the motor is stalled or
overloaded. This is normally a result of
excessive ingredients being processed at
one time. Should the mixer go into this
mode, the LED indicator band will flash and
the error message “E1” will flash on the LCD
screen and the buzzer will beep 3 times.
If this error occurs, turn the speed control
dial to the OFF position, switch the
appliance off at the power outlet and unplug
the cord. Remove some of the ingredients in
the mixing bowl and then restart the mixer.
THERMO CUT-OFF -
TEMPERATURE OVERLOAD
The mixer is equipped with a self-resetting
safety device which safeguards against
overheating the motor with excessive
loads. If overheating occurs, the mixer will
automatically activate the overheating
protection device and the motor will switch
itself off. Should the mixer go into this
mode, the LED indicator band will flash and
the error message “E2” will flash on the LCD
screen and the buzzer will beep 3 times.

17
PAge heAder.....
ASSEMBLY & OPERATION
If this error occurs, turn the speed control
dial to the OFF position, switch the
appliance off at the power outlet and unplug
the cord. Wait at least 15 minutes before
restarting the mixer.
DISASSEMBLING THE MIXER
1. When mixing is complete, turn the
speed control dial to the OFF/STANDBY
position, switch the appliance off at the
power outlet and unplug the cord.
2. Remove splash guard if assembled.
Separate pour spout then slide main
ring out of position.
3. Raise the mixer motor head by
depressing the tilt back button and lift
the mixer motor head up until it tilts
back and locks into the open position.
4. Remove the beater/dough hook/whisk
attachment by holding the mixer motor
head and pressing the attachment
upwards on the spindle. Turn the
attachment anticlockwise to release it
from the pin on the spindle.
5. Use a soft plastic spatula to remove
mixture from the beater, dough hook or
whisk attachment.
NOTE
When lowering or lifting the mixer,
always support the motor head with
your other hand to prevent from
free-falling.
6. Remove the mixing bowl from the
indented bowl locking recess of the
mixer base and turn anti-clockwise until
the bowl releases. Use a soft plastic
spatula to remove mixture from the
mixing bowl.
7. Lower the mixer motor head by
pressing the RELEASE button and
pushing the mixer motor head down
until it locks into the horizontal
(closed) position.
WARNING
Avoid contact with beater/dough hook/
whisk during operation. Keep hands,
hair, clothing, spatulas and other
utensils away from beater/dough hook/
whisk to prevent personal injury or
damage to the mixer.

CARE, CLEANING
& STORAGE
of your Breville product

19
CARE, CLEANING & STORAGE
CLEANING AFTER USE
1. Always ensure the speed control dial
is in the OFF position, the mixer is
switched off at the power outlet and the
power cord is unplugged.
2. Remove the beater, dough hook or
whisk attachment and mixing bowl
from the mixer. Follow instructions in
the Assembly and operation section of
this booklet.
3. Wipe the mixer motor head and
mixer stand with a soft, damp cloth
then dry thoroughly.
Wipe any excess food particles from the
power cord. Wash the bowl, beater, dough
hook, and whisk in warm soapy water with
a soft cloth or they can be washed in the
dishwasher. Rinse and dry thoroughly.
NOTE
Do not use abrasive scouring pads or
cleaners when cleaning the mixing
bowl, flat beater, dough hook or whisk
as these may scratch the surface.
Also ensure that the attachments
are not soaked in water for extended
periods of time, for example several
hours or overnight, as this may
damage the finish.
NOTE
Do not wash or immerse the mixer
motor head and mixer base in water
or any other liquid. Clean with a soft,
damp cloth and dry thoroughly. Do
not allow water or any liquid to enter
the gear system as damage may result.
SCRAPER BEATER
1. Wash the scraper beater in warm, soapy
water using a soft cloth or a soft bristled
brush. Rinse and dry thoroughly.
2. The scraper beater can also be washed in
the dishwasher (top shelf only).
3. A small bottle brush can be used to
clean inside the neck of the scraper
beater if needed.
STORAGE
Your Scraper Mixer Pro should be kept in a
convenient position on your kitchen bench
top or in an accessible cupboard.
Always ensure the speed control dial is
in the OFF position, the mixer is switched
off at the power point and the power cord
is unplugged.
Store the mixing bowl in the bowl locking
recess in the mixer base.
Place the attachments inside the mixing
bowl and lower the mixer motor head into
the horizontal (closed) position.
The motor head cannot be taken off the base
for any purpose.