Brickcom OSD-200 20xp User manual

2 Megapixel Speed Dome
Network Camera
OSD-200 20xp
User’s Manual

Product name:
Network Camera ( OSD-200A 20xp )
Release Date:
2012/12
Manual Revision:
V1.0
Web site:
www.brickcom.com
Email:
[e-mail]
[e-mail]
© 2012 Brickcom Corporation. All Rights Reserved

Table of Contents
Before You Use This Product .......................................................................................1
Regulatory Information.................................................................................................2
Chapter 1 - Package Contents......................................................................................3
Chapter 2 - 20x Outdoor Speed Dome Network Camera Overview ...........................4
Chapter 3 - Device Appearance Description ...............................................................6
Chapter 4 - Installation..................................................................................................8
4.1 Hardware Installation ......................................................................................8
4.2 Camera Connection.......................................................................................11
4.3 System Requirements...................................................................................12
4.4 Software Installation......................................................................................13
4.4.1EasyConfig ............................................................................................ 17
Chapter 5 - Accessing the Network Camera..............................................................22
5.1 Check Network Settings................................................................................22
5.2 Add Password to Prevent Unauthorized Access........................................22
5.3 Authentication................................................................................................23
5.4 Installing the Plug-In .....................................................................................24
Chapter 6 - Home.........................................................................................................25
Chapter 7 - System......................................................................................................28
7.1 System............................................................................................................28
7.2 Security ..........................................................................................................30
7.2.1User....................................................................................................... 30
7.2.2HTTPS................................................................................................... 31
7.2.3IP Filter .................................................................................................. 33
7.2.4IEEE 802.1X.......................................................................................... 34
7.3 Network ..........................................................................................................35
7.3.1Basic...................................................................................................... 35
7.3.2QoS........................................................................................................ 37
7.3.3SNMP .................................................................................................... 38
7.3.4UPnP ..................................................................................................... 39
7.4 DDNS ..............................................................................................................39
7.5 Mail..................................................................................................................40
7.6 FTP..................................................................................................................41
7.7 HTTP...............................................................................................................41
7.8 Application (Alarm Settings) ........................................................................41
7.9 Motion Detection............................................................................................46
7.10 Network Failure Detection.......................................................................51

7.11 Storage Management (Local Recording)................................................52
7.12 Recording (Local Recording)..................................................................54
7.13 Schedule...................................................................................................55
7.14 File Location (Snapshots and Web Recording).....................................56
7.15 View Information......................................................................................56
7.15.1 Log File.........................................................................................56
7.15.2 User Information...........................................................................56
7.15.3 Parameters...................................................................................57
7.16 Factory Default.........................................................................................57
7.17 Software Version......................................................................................58
7.18 Software Upgrade ....................................................................................58
7.19 Maintenance.............................................................................................59
Chapter 8 - Streaming .................................................................................................60
8.1 Video Format (Video Resolution / Video Deinterlace) ................................60
8.2 Video Compression.......................................................................................61
8.3 Video OCX Protocol.......................................................................................62
8.4 Video Frame Rate ..........................................................................................62
8.5 Audio (Audio Mode and Bit Rate Settings)..................................................63
Chapter 9 - PTZ............................................................................................................64
9.1 Preset..............................................................................................................64
9.2 Cruise .............................................................................................................65
9.3 Auto Pan.........................................................................................................66
9.4 Sequence........................................................................................................67
9.5 Home...............................................................................................................68
9.6 Tilt Range .......................................................................................................68
9.7 Privacy Mask..................................................................................................69
9.8 Camera—Exposure.......................................................................................71
9.9 Camera—WB (White Balance)......................................................................71
9.10 Camera—Misc 1(Miscellaneous Setups Menu 1) ..................................72
9.11 Camera—Misc 2(Miscellaneous Setups Menu 2)...................................74
9.12 Camera- Default .......................................................................................75
Chapter 10 - Logout.....................................................................................................76

1
Before You Use This Product
In many countries, there are laws prohibiting or restricting the use of surveillance
devices. This Network Camera is a high-performance, web-ready camera which can be
part of a flexible surveillance system. It is the user’s responsibility to ensure that the
operation of this camera is legal before installing this unit for its intended use.
Upon opening the product’s package, verify that all the accessories listed on the
“Package Contents” are included. Before installing the Network Camera, read the
warnings in the “Quick Installation Guide” to avoid misuse. When installing the Network
Camera, carefully read and follow the instructions in the “Installation” chapters to avoid
damages due to faulty assembly or installation.

2
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are
country dependent and are firmware programmed at the factory to match the
intended destination. The firmware setting is not accessible by the end user.

3
Chapter 1 - Package Contents
a. Network Camera
b. M3 Standard Screw (x1)M3 Security Screw (x1)
M5 Standard Screw (x1)
M5 Security Screw (x1)
Security Torx
Lubricant
c. Waterproof Rubber
d. Power
Connector
Alarm I/O
Connector
Audio
Connector
e. Outdoor Mount
Kit
f. Easy Installation
Guide
g. Product CD
h. Warranty Card

4
Chapter 2 - 20x Outdoor Speed Dome
Network Camera Overview
The Brickcom OSD-200A 20xp transmits digital video and audio data using wire
connection. The video encoder supports real-time H.264 Full HD resolution.
Simultaneous Quad Codecs, H.264 Baseline / Main / High Profile, MJPEG, are available
for various network applications via speeding or limited bandwidth. Better image quality
and high resolution are delivered by IP support.
By adopting a powerful 20x optical zoom lens with auto focus, OSD-200A 20xp can
easily provide clear close-up shots of objects. The Sony Progressive CMOS sensor and
removable IR-cut filter significantly improve the light sensitively of the OSD-200A 20xp,
providing excellent surveillance in both day and night settings. When its Wide Dynamic
Range (WDR) sensor, the camera can handle extreme variations of brightness within the
same sense.
Along with high-level sensors, the OSD-200A 20xp is equipped with a fast and precise
pan/tilt mechanical design. The 360ocontinuous pan and -10o~190otilt combine with a
preset speed of 5o ~400oper second to provide complete coverage of every angle.
With such powerful pan, tilt and zoom capabilities and a weather-proof casing (IP66),
this camera is perfect for environments where precision and reliability are key; such as
railway stations, airports, warehouses, and production facilities.
Features
▪2 Megapixel High Resolution Outdoor Speed Dome Camera
▪SONY 2M Progressive CMOS sensor
▪20x Optical Zoom, 10x Digital Zoom
▪Preset speed Up to 400∘/s
▪Brickcom WDR Enhancement® Technology inside
▪Removable IR-Cut Filter for Day and Night Function
▪H.264 HP/MP/BL&MJPEG compression, Quad stream support
▪1080p + D1 @30fps for dual stream
▪3D Privacy Masks for Private Area Protection
▪4sets DI/ 2 sets DO for External Alarm and Sensor Device
▪Built-In Micro SD slot/ 802.3at PoE
▪Weather-Proof (IP66) Casing with Built-in Fan and Heater

5

6
Chapter 3 - Device Appearance Description
< Bottom View >
Please refer to the illustrations below to connect power core through the supplied power
adaptor, and set up the audio according to the Audio pin definition.
< Power Connector> <Audio Connector>
NOTE- To power up the camera, please plug the AC 24V cable into the camera’s
power connector (Operating Temperature: -40℃-50℃); Or connect the Ethernet cable to
the camera’s Ethernet port and plug the other end of cable into an IEEE 802.3at High
Power over Ethernet (PoE plug)switch (Operating Temperature: -7℃-50℃)
Ethernet RJ45
10/100 Socket
Audio I/O
Micro SD Card Slot
Power
Factory Reset Button
Alarm I/O

7
< Ethernet Cable>
Use of Category 5 Ethernet cable is recommended for network connection; to have best
transmission quality, cable length shall not exceed 100 meters. Connect one end of the
Ethernet cable to the RJ-45 connector of the Network Speed Dome Camera, and the
other end of the cable to the network switch or PC.
Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit,
please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
<Alarm I/O Connector>
When cabling, please refer to the table below for pin definition of Alarm I/O setting.
Please make sure the alarm connections are properly.
< Dimension >
Mount Holder

8
Chapter 4 - Installation
4.1Hardware Installation
A. Before Installation
The OSD-200A 20xp is supplied with a dome cover to protect the
camera unit. Before installation, follow these instructions to attach the
dome cover and the mount holder.
1) Pull out the Dome cover and take out the mounting tape; and then
apply lubricant to the Dome cover’s water-proof rubber to make the
installation process smoother.
NOTE - The tiny protrusion on the dome cover must align with
one of the four holes on the dome body.
2) Attach the Dome cover to the Dome body by gently pressing down
on the sides of the Dome cover with both hands.
NOTE - DO NOT press the cover from the top as this may
cause damage to the Dome body.

9
3) Use a flat screw drive to fasten two supplied Flat Screws on the
Dome Cover.
4) Pass through all the power cable, I/O cable, audio cable, and
Ethernet cable into the mounting hold, and then attach the mount
holder tightly on the Dome body.
Optional Dome Camera Accessories
Transparent Cover (Standard) / Vandal Proof Cover (Optional)

10
B. Install Camera with Mount Kit
1) Make a cable entry hole on the wall/ ceiling to insert the cable(s).
2) Attach the waterproof rubber to the selected mount kit.
3) Route the Ethernet and I/O cables through the top holder and join
the selected mount kit with supplied screws and washers. Then
adjust the Waterproof Rubber over the joint.
4) Connect the Ethernet and I/O cables and hook the safety wired to
the camera.
5) Attach the camera to the top cover with the supplied screw and
washers.
Wall Mounting: Pendant Mount (mounting example)
NOTE - Refer to the mounting instruction in the “Speed Dome
Mounting Accessories Installation Guide” for more details.

11
4.2Camera Connection
1) Connect the camera to a switch using an Ethernet cable.
2) Connect supplied I/O cable to the camera.
3) To attach external devices, such as sensors and alarms, connect them to
the extension I/O terminal block.
Optional Dome Camera Accessories
Power Adapter
77H07-A1015 (Input: 100~115 VAC / Output: 24 VAC 36 VA)
77H07-A2015 (Input: 220~230 VAC / Output: 24 VAC 36 VA)
NOTE: When wiring, make sure the G / Y wire (Ground) inserted
into the mid-pin of the terminal block.

12
4.3System Requirements
Operating System:
Windows VISTA/ Windows XP / Windows 7
Computer:
Intel® Pentium® IV, 3 GHz or higher/ Intel® Core2 Duo, 2 GHz or higher
Memory:
1GB or more
Monitor:
1024 x 768 pixels or more, 24-bit True color or better
Network Interface:
10/100Mbps Network interface card must be installed
Web Browser:
Internet Explorer 6.0 or later, Firefox, Chrome, Safari
Adobe Reader:
Adobe Reader 8.0 or higher
Viewer:
ActiveX control plug-in for Microsoft IE
Items
Minimum Requirement
Personal Computer
3. AGP graphics card 64 MB RAM, DirectDraw
Network Card
10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation

13
4.4 Software Installation
In this manual, "User" refers to whoever has access to the Network Camera, and
"Administrator" refers to the person who can configure the camera and grant user
access to the camera.
After checking the hardware connection, run the Installation Wizard program
included on the product’s CDROM to automatically search the intranet for the
camera. There may be many cameras on the local network. Differentiate the
cameras using the serial number which is printed on the labels on the carton and the
bottom of the camera.
A. Insert the Installation CD into the CD-ROM driver. Run AutoRun Tool
directly from the CD-ROM to start the installation. When installing the
Brickcom software kit for the first time, select a desired language for the
interface. The available languages are listed in the scroll box. Click
<Install> and follow the steps to install the EasyConfig wizard on the
desired computer.

14
B. In the Install Shield Wizard dialog box, click <Next> to continue.
C. Read the End-User License Agreement and check the option “I accept the
terms of the license agreement”. Click <Next> to continue.

15
D. Click <Change> to change the appointed folder where installation and
program files will be stored. Click <Next> to continue.

16
E. Select to create shortcuts. Click <Next> to continue.
F. Select the application and click <Finish>. When launching the PC-NVR
program, please refer to the PC-NVR user manual.