Brink Indoor Mixfan Reference guide

Installation regulations
Indoor Mixfan
English

Contents
1 Introducon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Precauons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Installaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Mounng of the product. . . . . . . . . . . . . . . . . . . . . . 6
2.2 Electrical connecon. . . . . . . . . . . . . . . . . . . . . . . . 10
2.2.1 Connecng as single unit. . . . . . . . . . . . . . . . . 10
2.2.2 Connecng as Master-Slave mode. . . . . . . . . 10
2.3 Set up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Reset conguraon. . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Fault. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 Operaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 User instrucon. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Maintenance - period indicaon. . . . . . . . . . . . . . . 14
4.2 Maintenance - instrucons. . . . . . . . . . . . . . . . . . . 14
5 Service arkelen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Exploded view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Conformity declaraon. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7 Recycling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installation regulations
Indoor Mixfan
Store near the appliance
This appliance may be used by children as of 8 years of age, persons with reduced
physical or mental capacities, and persons with limited knowledge and experience if
they are supervised or have received instructions on how to use the appliance safely
and are aware of the possible dangers.
Children younger than 3 years of age must be kept away from the appliance, unless
they are under constant supervision.
Children between the ages of 3 and 8 may only switch the appliance on or off, but only if
supervised or if they have received clear instructions on the safe use of the appliance
and understand the possible dangers, on the condition that the appliance has been
placed and installed in the normal position for use. Children between the ages of 3 and
8 may not insert the plug into the socket, nor clean or make changes to the settings of
the appliance, nor carry out any maintenance on the appliance that would normally be
carried out by the user. Children may not play with the appliance.
If you need a new power cable, always order the replacement from Brink Climate
Systems B.V. To prevent dangerous situations, a damaged mains connection must only
be replaced by a qualified expert!
Country: GB

1 Introduction
1.1 Precautions
This product is artistically made in conformity to applicable CEE rules and is manufactured to allow rooms and
similar air change, wherever the product is installed. Please follow all these indication to ensure performance,
mechanical and electrical reliability and keep always this instruction leaflet. Do not use this product for different
application unless indicated by us.
1. Remove packing and make sure that the appliance is undamaged.
2. Check that your electrical voltage and frequency correspond to those marked on the fan rating label; Install
the product so that the blades are at a height of at least 2,3 m above the floor.
3. This appliance must only be used for the purpose it was built for, i.e. air replacement for domestic and similar
purposes.
4. Do not operate the appliance in the presence of inflammable vapours (alcohol, petrol, etc.).
5. Before carrying out any cleaning or maintenance disconnect the mains electrical supply to the fan by means of
a double pole switch or remove the plug. Any maintenance and cleaning operation that requires dismounting
the unit must only be done by someone who is a property qualified person.
6. Make sure you have completely assembled the product before running.
7. Periodically, at least once a year or more frequently in case of heavy use, remove dirt and incrustation from the
impeller and motor casing. It is also very important to make sure the impeller is not deformed or cracked, is
able to rotate freely and without oscillation, and is properly fixed to the shaft.
8. Installation must be carried out by qualified personnel according to manufacturer’s instructions. Incorrect
installation can cause damage to people, animals or properties for which the manufacturer cannot be
considered liable.
9. The fan is a fixed appliance and the main supply must be done by flexible cable with plug or by a onnipolar
switch with a minimum opening of the contacts of 3 mm.
10. When installing the fan in a room containing a combustion heater ensure that there is sufficient air to supply
both appliances. This is to ensure the efficient operation of the heater and to allow a proper operation of the
fan.
Indoor Mixfan 616190-C

1.2 Product overview
The product is mainly composed of a ventilation unit with a CO2sensor that will be placed outside the room in
which you want to change air, a grill that will be placed inside the room and a tube of sound absorbing material.
1. Ventilation unit
It is composed of a low power absorption DC motor, impeller, PCB board with integrated CO2sensor, plastic
parts.
2. Aesthetic cover
3. Cover cap
This component is used to prevent that air flow to the ceiling when the product is mounted close to it.
The cover cap can be removed in case it is not necessary.
4. Grill
5. Sound absorbing material
This is used to improve the acoustic performance of the product.
Indoor Mixfan 616190-C Brink / 5

2 Installation
2.1 Mounting of the product
The installation of this product is reserved exclusively to qualified personnel. Make sure that the power system in
the installation room is disconnected before the electrical assembling operations.
The product must not be installed close to curtains or cloths, because these could affect its functioning. Before
the mounting operations of the product, read carefully and strictly follow the instruction manual and make sure
to have all the necessary equipment for the installation.
For the proper functioning of the system, it is important that the ISSO guidelines regarding to air overflow must
be considered. These are as follows:
▪The net cross-section of the fresh air supply must be at least 0.0012 m² per dm³/s of the required air volume
flow, based on an average air speed of 0.83 m / s in the opening.
▪The air overflow is often done by a gap under a door. Also special airflow control devices are used, for example
in the door or wall. These facilities should never be blocked.
Pre-disposition
Room Corridor/
Central hall
Note the gap height used under the door.
1 Grill
2 Fan unit
F = W - 25mm
W= Thickness of the wall
Room Corridor
Indoor Mixfan 616190-C

Corridor/ Central Hall
Use the right type of fixing screws
See Chapter:
"Installation configuration"
See Chapter:
"Installation - Electrical wirings"
Mount the top sealing cap only
if distance to ceiling <50cm
A = 230 V
B = Cascade only
Indoor Mixfan 616190-C Brink / 7

Installing the cover cap (if required)
Indoor Mixfan 616190-C

Room
Use the right type of fixing screws
Indoor Mixfan 616190-C Brink / 9

2.2 Electrical connection
2.2.1 Connecting as single unit
2.2.2 Connecting as Master-Slave mode
The use of the system as MASTER-SLAVE is recommended only in case the products are installed in a single
room.
1. Master
2. Slave 1
3. Slave 2
A maximum of two SLAVES can be connected.
Warning:
In case of installaon with MASTER-SLAVE system, the MASTER unit is the only to detect the environmental
condions through its CO2 sensor and is therefore able to control every part of the system.
Warning:
During the master-slave conguraon process is mandatory that, for all the products, the dip switch
SERVICE/STAND-BY is set to “OFF”
Service/ Stand-By
Indoor Mixfan 616190-C

2.3 Set up
During the process of setting up (configuration) the desired flow rate value and the CO2levels can be selected.
Please follow the underneath diagram to set up the products:
The two-way dip switch helps either to select the max air ow rate among the 3 pre-seled levels
in case of MASTER unit or to select the unit as SLAVE.
Master Master Master Slave
Max 35 m3/h Max 50 m3/h Max 70 m3/h
The three-way dip switch helps to select the CO2 intervenon levels and the switching on/o of the
product.
Minimum
CO2level
(Default 800 PPM)
Maximum
CO2level
(Default 1200 PPM)
On = Normal operation
Off = Service/Stand-By
800 PPM 1200 PPM On
600 PPM 1000 PPM Off
Indoor Mixfan 616190-C Brink / 11

The functioning ratio of the product according to the selected configuration follows the underneath diagram:
2.4 Reset configuration
To change the setting up of the flow rate, CO2levels or to change the functioning mode MASTER/SLAVE is
necessary to:
▪Switch off the machine,
▪select the new desired configuration,
▪switch on the machine again .
Warning:
If you change the conguraon of the dip-switch while the machine is running, this won’t detect
any change and will go on running according to the former sengs.
2.5 Fault
When the appliance’s control system detects a fault, that is indicated by one blinking red LED or by a sound
emitted from the buzzer. The appliance remains in the fault mode until the problem in question has been solved
Then the product will reset itself and start again depending on the set-up of dip-switches.
Fault nr. Cause Action appliance Action installer
1CO2 value lower than 0 PPM or
higher than 5000 PPM
Red LED blinking
Intermient Sound from buzzer
Check environmental CO2 level
Replace venlaon unit
2CO2 signal lost or CO2 sensor
damaged Red LED blinking
Check CO2 sensor
Replace venlaon unit
3SLAVE doesn’t receive signal
from MASTER Red LED blinking
Check wiring connecon between
MASTER-SLAVE
Check dip-switching conguraon
Indoor Mixfan 616190-C

3 Operation
3.1 User instruction
Once the product has been set up it will work fully automacally.
The speed of the fan will increase/decrease gradually and automacally according to the CO2 level present in the
environment.
If the detected CO2 level of the environment is higher than the warning one (2000ppm) the product will produce a tone to
warn the user about the emergency situaon.
Indoor Mixfan 616190-C Brink / 13

4 Maintenance
4.1 Maintenance - period indication
It is recommended to clean the product at least once every year . During the rst months of running, it is also
recommended to periodically control the condions of the machine so that to establish a proper slot me according to
the environmental condions in which the product is installed.
4.2 Maintenance - instructions
Warning!
Make sure that the electrical connecon in the installaon room is disconnected before the
maintenance operaons.
Indoor Mixfan 616190-C

5 Service artikelen
5.1 Exploded view
Example
Appliance type : Indoor Mixfan 70 m³/h
Serial Number : 520375194706051605
Year of production : 2020
Part : Fan unit
Artikel code : 520375
Quantity : 1
N. B.:
Appliance type, serial number and year of production are
stated on the identification plate behind the plastic front
panel (central hall side) on the appliance.
When ordering parts, indicate the relevant article code number (see exploded view):
No. Article description Artikel code
1S. Indoor Mixfan –Fanunit 535100
2S. Indoor Mixfan – Front Brink 535101
Indoor Mixfan 616190-C Brink / 15

6 Conformity declaration
Conformity declaration
Manufacturer: Brink Climate Systems B.V.
Address: Postbus 11
NL-7950 AA, Staphorst, The Netherlands
Product: Heat recovery appliance type:
Indoor Mixfan
The product described above complies with the following directives:
¨2014/35/EU (low voltage directive)
¨2014/30/EU (EMC directive)
¨RoHS 2011/65/EU (substances directive)
The product bears the CE label:
Staphorst, 24-11-2017
M. Schouten
Technical Director
Indoor Mixfan 616190-C

7 Recycling
Recycling
Sustainable materials are used in the manufacture of this appliance.
The packaging should be disposed of in a responsible manner and in
accordance with governmental regulations.
Indoor Mixfan 616190-C Brink / 17

Brink Climate Systems BV
P.O. Box 11 NL-7950AA Staphorst
T [phone]
E [e-mail]
www.brinkclimatesystems.com
www.brinkairforlife.com
616190-C