Brinly P20-500BH User manual

Call Customer Service, Toll-Free: 877-728-8224
Important: This manual contains information for the safety
of persons and property. Read it carefully before
assembly and operation of the equipment!
Visit us on the web!
www.brinly.com
PUSH SPREADER
MODEL:
P20-500BH
OWNER'S MANUAL
• Assembly
• Installation
• Operation
• Repair Parts
1008066-E© 2020 Brinly-Hardy Company
English, Spanish &
French Manual

English Manual 1008066-E
2
==================================================================================================
INTRODUCTION AND SAFETY
CONGRATULATIONS on your new Brinly-Hardy Spreader! This accessory has been designed, engineered and
manufactured to give you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please do not hesitate to contact our knowledgeable
customer service department toll-free at 1-877-728-8224. We have competent, well trained technicians to help you with
the assembly and use of your spreader.
CUSTOMER RESPONSIBILITIES
- Please read & retain this manual. The instructions will enable to assemble and maintain your product properly.
- Please carefully read and observe the SAFETY SECTION of this manual.
- Follow a regular schedule in maintaining and caring for your Brinly-Hardy product.
TABLE OF CONTENTS
SAFETY ......................2-3
PARTS BREAKDOWN ...........4-5
ASSEMBLY ....................6-9
OPERATION
AND MAINTENANCE .......... 10-11
APPLICATION RATE CHART .... 12-15
WARRANTY ....................16
MANUAL EN ESPAÑOL ........ 17-32
MANUAL EN FRANÇAIS ....... 33-48
SAFETY
This symbol will help to point out important
safety precautions throughout this manual.
It means: ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED.
The machine safety labels shown in this section are placed in
important areas on your machine to draw attention to potential
safety hazards.
On your machine safety labels, the words DANGER, WARNING,
and CAUTION are used with this safety-alert symbol. DANGER
identies the most serious hazards.
The operator’s manual also explains any potential safety
hazards whenever necessary in special safety messages that
are identied with the word, CAUTION, and the safety-alert
symbol.
RECORD PURCHASE INFORMATION
Record your purchase information in
the spaces provided below:
Date of Purchase _________________________________
Company Name _________________________________
Company Phone _________________________________
Serial Number _________________________________

English Manual 1008066-E
3
==================================================================================================
SAFETY
STOP
Installation Questions?
Missing Parts? Replacement Parts?
DON’T GO BACK TO
THE STORE!
Please call our Customer Service
Department, Toll Free: 877-728-8224
or [e-mail]
- Keep bystanders away when you operate this machine.
- Use this machine for intended purpose only.
- This machine is intended for use in lawn care and home
applications.
- Do not let children or an untrained person operate
machine.
- Keep all parts in good condition and properly installed. Fix
damaged parts immediately. Replace worn or broken parts.
- Do not modify the machine or safety devices. Unauthorized
modifications to the machine may impair its function and
safety, and void the warranty.
- Do not let anyone sit or ride on equipment during
operation. Keep riders off attachment.
- Wear substantial footwear and long trousers. Do not
operate the equipment when barefoot or wearing open
sandals.
- Do not wear loose fitting clothing that can get caught in
moving parts.
- Always wear eye protection when operating the equipment.
- Stay alert for holes in the terrain and other hidden hazards.
- Watch out for traffic when crossing or near roadways.
- Before you operate any feature of this machine, observe
your surroundings and look for bystanders.
- Always wash hands after contact with fertilizers and
pesticides.
- Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
OPERATE SAFELY NOTES

English Manual 1008066-E
4
==================================================================================================
Ref. Description Part # Qty
1 Handle spacer 1007081 1
2 Carriage bolt, M6 x 25 1007082 1
3 Washer, M6 1007083 1
4 Gauge and lever assembly 1007084 1
5 Adjust handle assembly 1007085 1
6 Adjust handle knob side 1 1007086 1
7 Adjust handle knob side 2 1007087 1
8 Screw, M4 x 18 1007088 1
9 Handle spacer 1007089 1
10 Wing nut, M6 1007090 1
11 Bolt, M6 x 45 1007091 7
12 Nylon washer 1007092 1
13 Flat washer, M6, big 1007093 1
14 Screen 1007094 1
15 Handle cover 1007095 2
16 Hopper Assembly, Black* 1008017* 1
17 R pin, M2 diameter 1007097 1
18 Hopper bushing 1007098 1
19 Pivot and bracket assembly 1007099 1
20 Wheel frame tube 1007100 2
21 Nut, M6 1007101 2
22 End cover 1007102 2
23 Upper handle 1007103 2
24 Lock nut, M6 1007104 11
25 Control rod A 1007105 1
26 Handle shaft 1007106 1
27 Shut off plate 1007107 1
28 Flat washer, M4, big 1007108 3
29 Screw, M4 x 12 1007109 3
30 Frame 1007110 1
31 Frame brace 1007111 2
32 Bolt, M6 x 50 1007112 2
Ref. Description Part # Qty
33 Bolt, M6 x 30 1007113 2
34 Flat washer, M16 1007114 1
35 End cap 1007115 2
36 Pneumatic wheel (Yellow Hub) 1007116 2
Pneumatic wheel (Gray Hub) 1008781 2
37 Axle bushing 1007117 2
38 Axle bearing 1007118 2
39 Gearbox & axle assembly 1007119 1
40 2.9 x 28mm Cotter Pin, SS 1008031 1
41 Screw, M4 x 20 1007121 1
42 Impeller 1007122 1
43 Screw, M6 x 40 1007123 4
44 Hex locknut, M5 1007124 1
45 Cross brace 1007125 1
46 Adjust connect rod, B 1007126 1
47 Hex bolt, M5 x 45 1007127 1
48 Flat washer, M6 1007128 3
49 Cotter Pin, Small 1008098 2
50 Nylon Washer 1007531 4
51 Decal, Brinly B-5924 1
PARTS BREAKDOWN
* Assembly includes Part Numbers :
16, 18, 27, 28, 29
STOP
Installation Questions?
Missing Parts? Replacement Parts?
DON’T GO BACK TO
THE STORE!
Please call our Customer Service
Department, Toll Free: 877-728-8224
or [e-mail]

English Manual 1008066-E
5
==================================================================================================
22
15
23
24
26
4
48
1
23 8
7
24
13
5
12
25
21
46
48
24
11
31
30
45
31
32
33
24
24
32
14
17
18
30
39
41 40
36
43
47 35
44
36
37
38
38
37
50
50
34
35
20
28
51
27
29
42
20
16
33
11
20
20
11
15
6
10
9
3
2
22
Hopper/Frame/Axle Exploded
Handle/Frame Exploded
50
50
49
11
19
PARTS BREAKDOWN

English Manual 1008066-E
6
==================================================================================================
TOOLS REQUIRED: 2- 10mm Wrenches
1. Remove two M6 locknuts
and M6 x 45mm long bolts
to remove pivot and bracket
assembly from wheel
frame tubes.
NOTE:
Set bolts and nuts to the
side. You will re-install
them in Step 3.
ASSEMBLY
2. Tilt arm assembly, and
insert rod into flow control
handle.
Figure 2
Figure 1

English Manual 1008066-E
7
==================================================================================================
3. Insert arm assembly
between frame tubes.
Re-install pivot and
bracket assembly through
wheel frame tubes and
arm assembly with two
M6 x 45mm bolts and
M6 locknuts removed in
Step 1.
ASSEMBLY
4. Tighten nuts and bolts on
both sides of spreader at
locations shown.
Figure 4
Figure 3

English Manual 1008066-E
8
==================================================================================================
10
15
20
25
30
10
15
20
25
30
5. Push the flow control handle
downward to the fully closed position,
close the shut off plate under the
hopper, and hand tighten bottom nut
on linkage rod until snug.
Then, hand tighten the top nut
on linkage rod until snug.
ASSEMBLY
6. NOTE: The edge of the wingnut is the marker, and not the
center of wingnut. When the flow control handle is opened
fully, the edge of the wingnut should be on the 30 mark.
Set edge of wingnut on 30 mark and tighten.
Move flow control handle upward and back downward, and
verify the shut off plate under hopper opens and closes
properly. If necessary, adjust linkage rod nuts and
tighten hand tight.
Figure 6
Figure 5

English Manual 1008066-E
9
==================================================================================================
AVOID DAMAGE!
Only use a wrench on the LOWER nut.
DO NOT use a wrench
on the upper nut.
7. Once adjustment is
complete, tighten lower nut
on linkage rod with wrench.
Figure 7
8. Handle can be
lowered by removing
bolts and nuts and
moving handle
assembly downward,
using upper holes for
bolts and nuts.
Figure 8
ASSEMBLY

English Manual 1008066-E
10
==================================================================================================
READ BEFORE USING:
Become familiar with the operation of the spreader
BEFORE you put material in the hopper.
Practice walking with the spreader, opening and closing the
rate gate at the appropriate times.
Travel at a constant speed and operate the spreader lever position.
Remember: Open the rate gate after the spreader is in motion at
operating speed (about 3 mph, or at a brisk walking pace).
Close the rate gate while spreader is still at operational speed.
FLOW CONTROL SETTING INFORMATION
The ow control lever operates the control plate. The control
lever plate is marked 0-30. The position selected determines
the amount of material to be broadcast. The higher the number,
the heavier the application of the material. This allows for
accurate control of the spreading rate.
The fan speed and the spread width are controlled by the
speed at which you operate the spreader. The spread width
also depends on the volume/density, and the particle size of
the material.
The spread thins or feathers at the outer edges, eliminating
sharp, "Edge Of Spread" lines which cause stripes and streaks.
Extra coverage can be given under trees and other heavy
feeding areas without showing "Edge Of Spread" lines.
Gaps and double overlaps are less likely. Small errors in travel
are forgiven and do not show.
FILLING THE SPREADER
OPERATING TIPS
• Push ow control lever down towards
the hopper to close the rate gate.
• Fill the spreader on a at, level surface only. Fill on
sidewalk, driveway, cardboard, etc. to avoid material loss.
• DO NOT overload with more than the maximum
capacity of 50 lbs.
• DO NOT use on windy days.
• When lling hopper with material, always use
screen to help break up clumps.
• Keep spinner blade clean. Excess material build-up
can cause an uneven spread pattern.
• Keep the impeller level when spreading.
SPREADING MATERIAL
Determine setting required for the product you are spreading
(See Application Rate Chart). If a setting is not found, use a
similar size/weight material. Determine a ow control setting
on the low side. If the setting proves to be too low, cover the
area more than one time. A higher setting can be used when
a proven setting is established. Generic Grass Seed and
Fertilizer Settings are shown at the end of the list.
Remember: Published ow control settings are approximate
only. The operation of the spreader, the condition of the
material (damp or dry or over-pulverized) and weather
conditions, are all contributing factors. For these reasons, it
is often a good idea to spread the area 2 times - or one-half
rate - in cross directions. One-half rate settings are highly
recommended under damp and humid conditions.
ROTARY AGITATOR
Use the rotary agitator only if needed. Free-owing,
lump-free materials will not require the agitator. The rotary
agitator is easily installed or removed.
Never leave fertilizer or other material in the hopper. It
can draw moisture, form clumps, and cause unnecessary
rusting or jamming of controls and other parts. Ice melt
residue is especially corrosive. Clean and oil spreader
immediately after each use.
WARNING
OPERATION
AVOID INJURY!
Chemicals can be dangerous.
Avoid injury to operator or bystanders:
• Read chemical container label for handling instructions. A
Material Safety Data Sheet (MSDS) should be supplied by
the chemical dealer and provides proper safety information.
• Wear proper clothing and safety equipment while handling or
applying chemicals.
• Prohibit all smoking, drinking, and eating around chemicals.
• When spreading products containing herbicides, exercise
extreme caution with respect to careless spreading and to
wind-drift. CONTACT OF SOME PRODUCTS ON SOME
PLANTS CAN BE FATAL.

English Manual 1008066-E
11
==================================================================================================
READ BEFORE USING:
NOTE: When determining required setting, the edge of
the wingnut is the marker, and not the center of wingnut.
When the ow control handle is opened fully, the edge of
the wingnut should be on the 30 mark.
IMPORTANT: REMEMBER TO START AND STOP THE
SPREAD WHILE MOVING. Do not open the ow control
lever while stopped or material will simply run onto the
ground without being spread.
HEADER STRIPS
Spread header strips at each end of area. This allows a turn-
around area to align spreader for next pass. Then start on the
edge of the area to be spread. Spread until you hit the header
area. Turn the ow control handle to off while still moving. Make
your turn and start down the next row. Turn the ow control
handle back on as you hit the edge of your header area. Turn
the ow control handle on while moving.
Header
6’ 6’3’
Header
SPREADING ICE MELT
• Remove screen from hopper to prevent damage.
• Start with ow control setting at 20 and make a trial pass.
Adjust as needed to increase or decrease coverage.
• When complete be sure to thoroughly clean spreader as ice
melt can be highly corrosive.
• Re-install screen when complete.
CALIBRATING SHUT OFF PLATE
See Figure 6 and Figure 7 on pages 8 - 9.
MAINTENANCE
• To ensure years of trouble-free service, clean the spreader
thoroughly after each use. Move ow control handle as you
rinse to avoid build up of material.
• For rust on frame parts, sand lightly and paint with enamel.
• Periodically lubricate all bearing surfaces.
• Never allow material to remain in hopper for extended
periods of time.
• Periodically check all fasteners for tightness.
TROUBLESHOOTING
Flow control handle is hard to actuate or will not move:
Check for buildup of material between bottom of hopper and
shut off plate. Clean as needed.
OPERATION
10
15
20
25
30
10
15
20
25
30
SERVICE
If you have installation questions, are missing parts or need
replacement parts, don’t go back to the store! Please nd your
product serial number and model number, then contact our
Customer Service department:
In North America and Canada
call Toll-Free: 877-728-8224
Chat online: www.brinly.com
Email: [e-mail]
Additional info and videos are
available on our website: brinly.com

English Manual 1008066-E
12
==================================================================================================
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
All American
All Purpose Fertilizer 10-10-10. 10 16.0
Bayer
Season Long Grub Control 3.8 15.0
Season Long Grub Control 2.9 13.5
Complete Insect Killer 3 13.5
Complete Insect Killer 2 12.0
Power Force Multi-Insect Killer 3 12.0
Power Force Multi-Insect Killer 2 11.0
Grub Control 3 12.0
Grub Control 2 12.0
Lawn Fertilizer Plus Weed Control II
30-3-4
3.2 13.5
Season Long Grub Control 3.8 13.5
Season Long Grub Control 2.9 12.0
Lawn Starter Fertilizer 20-27-5 3.6 13.5
Lawn Fertilizer Plus Crabgrass
Preventer 30-3-4
3.2 13.5
Eliminator
Ant, Flea, and Tick Killer Granules 3 13.5
2.5 12.0
2 12.0
5% Diazinon Insect Killer Granules 2 13.5
Howard Johnsons
All-purpose Fertilizer 8-8-8 7 15.0
All-purpose Fertilizer 10-10-10 7 15.0
All-purpose Fertilizer 12-12-12 7 15.0
Ironite 1-0-0 5 13.5
Klay
Soft Pelletized Gypsum Soil
Conditioner
4 13.5
Soft Pelletized Gypsum Soil
Conditioner
3 12.0
Soft Pelletized Gypsum Soil
Conditioner
2 12.0
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Lesco
46-0-0 2.2 15.5
39-0-0 2.6 15.5
34-3-11 2.9 16.0
32-3-8 3.1 16.0
30-3-7 3.3 16.0
28-5-12 3.6 16.0
24-5-11 4.2 16.0
19-19-19 5.3 16.0
18-24-12 4.2 15.0
24-2-11 4.2 15.0
26-2-11 3.8 15.5
24-0-11 4.2 16.0
18-0-18 Fall/Winter 4.2 16.0
17-17-17 All Purpose 5.9 16.0
16-4-8 6.3 16.0
15-5-10 6.7 16.0
15-0-15 6.7 16.0
Atrazine +17-2-11 6.0 16.0
Dimension .015% +19-3-6 3.5 16.0
Mach 2™ 1.33% +24-5-11 3.4 16.0
Merit® 0.2% +24-5-11 3.5 15.5
Momentum® + Fertilizer 3.6 15.0
PCNB 12.5% 10-0-20M 75%PPSCU 4.0 15.5
PRE-M® 1.5% + Fertilizer 2.3 15.0
PRE-M® 0.86% + Fertilizer 4.0 16.0
Talstar® 0.069% + Fertilizer 3.3 16.0
Weed & Feed +18-0-9 4.0 15.5
Weed & Feed +18-2-9 4.0 15.5
Dylox® 6.2* 3.0 16.0
Master Turf
Ultimate Tall Fescue Blend 8 17.0
Ultimate Tall Fescue Blend 4 15.0
Milogranite 6-2-0 8 17.0
Milogranite 6-2-0 16 20.0
Miracle-Gro
Lawn Fertilizer plus Weed Control
28-3-3
3.2 13.5
Starter Lawn Fertilizer 20-27-5 3.6 13.5
Starter Lawn Fertilizer 29-3-4 3.1 12.0
APPLICATION RATE CHART

English Manual 1008066-E
13
==================================================================================================
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Ortho
Lawn Insect Killer Granules 9.6 16.0
Lawn Insect Killer Granules 4.8 13.5
Lawn Insect Killer Granules 2.4 11.5
Lawn Insect Killer Granules 1.2 11.5
Max Insect Killer for Lawns 4 13.5
Max Insect Killer for Lawns 2 12.0
Max Insect Killer for Lawns 1 11.5
Parkers
Super Soilife Lawn & Garden Fertilizer
10-10-10
10 16.0
Super Soilife Lawn & Garden Fertilizer
16-4-8
6.5 13.5
Pennington
Lawn Starter Fertilizer 18-24-6 3.6 15.0
Master Turf High Trafc Lawn Seed
Mixture
10 18.0
Master Turf High Trafc Lawn Seed
Mixture
5 16.0
Master Turf Shady Lawn Seed Mixture 8 18.0
Master Turf Shady Lawn Seed Mixture 4 16.0
Master Turf Sun & Shade Lawn Seed
Mixture
10 18.0
Master Turf Sun & Shade Lawn Seed
Mixture
5 16.0
Lawn Food 27-4-6 3.6 16.5
Centipede Food 18-0-18 4.0 17.0
St. Augustine, Bahia & Bermuda Food
26-6-9
4.0 18.0
Fall Lawn Food 10-5-15 4.0 15.5
Crabgrass Preventer plus Fertilizer
5-10-25
4.0 16.5
Lawn Starter 18-24-6 3.6 16.5
Weed & Feed w/Atrazine 25-4-6 4.0 17.0
Fescue Food 28-5-10 4.0 16.5
Weed & Feed w/Triamine 25-4-6 3.6 16.5
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Real-Kill
Multi-Purpose Lawn and Garden Insect
Killer
2 12.0
Multi-Purpose Lawn and Garden Insect
Killer
2.5 12.0
Rebel's
Supreme Blend Grass Seed for Sun &
Shade
10 18.0
Supreme Blend Grass Seed for Sun &
Shade
5 16.0
Ringer
Lawn Restore 10-2-6 10 18.0
Sam's Choice
Crabgrass Preventer 30-3-4 12.3 19.0
Crabgrass Preventer 30-3-4 8.1 16.0
Crabgrass Preventer 30-3-4 6 16.0
Crabgrass Preventer 30-3-4 5.4 15.0
Insect Control Plus Fertilizer 28-4-6 3 12.0
Lawn Food 29-3-4 3.2 13.5
Starter Fertilizer 20-27-5 6 16.0
Starter Fertilizer 20-27-5 3.6 13.5
Scotts
Classic Grass Seed Fall Grass Seed
Mix
4 16.0
Classic Grass Seed Fall Grass Seed
Mix
2 13.5
Grubex 2.3 12.0
Grubex Season Long Grub Control 3.1 13.5
Grubex Season Long Grub Control 2.3 13.5
Lawn Fungus Control 1.4 12.0
Lawn Fungus Control 2.7 13.5
Pure Premium Kentucky Bluegrass Mix 2.2 13.5
Pure Premium Kentucky Bluegrass Mix 1.1 12.0
Pure Premium Sun & Shade Grass
Seed Mixture
2.5 13.5
Pure Premium Sun & Shade Grass
Seed Mixture
1.25 12.0
Starter Fertilizer 20-27-5 3.6 13.5
APPLICATION RATE CHART
...continues on page 14

English Manual 1008066-E
14
==================================================================================================
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Scotts, continued
Starter Fertilizer 20-27-5 5.9 13.5
Turf Builder 28-3-8 2.7 13.5
Turf Builder Lawn Fertilizer 29-3-4 3.1 12.0
Turf Builder with Summer Guard 2.7 13.5
Turf Builder Plus Weed Control 2.9 13.5
Winterizer 22-4-1 3.3 11.5
Turf Builder + Halt 25-3-3 3.6 15.0
Turf Builder Plus 2 Weed Control &
Lawn Fertilizer 26-3-3
3.5 14.5
Turf Builder Lawn Fertilizer New
Concentrated Nuggets 34-4-4
2.7 13.5
Starter Fertilizer 17-23-6 4.0 15.0
Lawn Disease Preventer 2.7 15.5
Lawn Weed Control 25-4-6 1.0 11.5
Turf Builder 28-3-3 3.2 17.0
5.0 20.0
Weed & Feed 33-3-3 2.5 13.5
SCOTTS PRO TURF
Fungicide VII 8-2-1 25.0 25.0
12.7 27.0
13.4 13.0
Turf Builder Lawn Fertilizer 29-3-4 8.2 15.5
Turf Starter w/ Poly S 16-26-12 4.1 18.0
Fertilizer + Fungicide VIII 23-3-3 1.6 13.5
HD Fertilizer + Iron 29-3-3 3.2 14.5
HD Fairway Fertilizer 32-3-10 3.1 16.5
Fertilizer with Minors 26-4-13 3.9 14.5
Hi K Greens Fertilizer 15-0-30 3.4 13.5
HD Starter (Small Granule) 19-26-5 3.5 14.5
Hi K Fertilizer 15-0-30 3.4 15.5
Moss Control 16-0-0 3.9 13.0
Iron-S 16-0-0 1.7 13.5
Super Greens Fertilizer 19-0-17 4.6 14.5
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Scotts, continued
Turf Fertilizer + 2% Fe w/PolyS 25-3-
10
3.3 16.5
ProTurf Fertilizer w/PolyS 34-3-6 2.8 16.5
NPK Turf Fert. w/PolyS 21-3-20 4.6 16.5
Fungicide X 4.9 15.5
FF-II 14-3-3 4.7 13.5
Systemic Fungicide 2.6 15.0
Fertilizer Plus Preemergent Weed
Control 22-4-4
3.3 18.0
3.8 18.5
4.5 19.5
4.9 20.0
Turf Fertilizer Plus Preemergent Weed
Control 22-0-6
3.8 18.5
4.2 19.5
4.9 20.0
5.8 21.0
6.1 22.0
8.7 27.0
9.6 30.0
SCOTTS FOUR SEASON PROGRAM
Step 1 - Crabgrass Preventer plus
Fertilizer
3 15
Step 2 - Weed Control plus Fertilizer 2.5 15
Step 3 - Insect Control plus Fertilizer 3.1 16.5
Step 4 - Lawn Fertilizer 2.8 15.5
APPLICATION RATE CHART

English Manual 1008066-E
15
==================================================================================================
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Sevin
Lawn Insect Granules 4.6 13.5
Lawn Insect Granules 2.33 13.5
Lawn Insect Granules 2.25 13.5
Spectracide
Grub Stop 3 13.5
Triazicide Insect Killer Granules 3 11.5
Sta-Green
Lawn Fertilizer 29-2-5 3.6 13.5
Lawn Weed Control 2 12.0
200 Plus Weed & Feed 28-3-3 3.2 13.5
Starter Fertilizer 18-24-10 3.6 13.5
Weed & Feed 28-2-4 3.2 13.5
Sun & Shade Grass Seed Mixture 10 18.0
Sun & Shade Grass Seed Mixture 5 16.0
Vigoro
Insect Control Plus Fertilizer 3 11.5
Starter Fertilizer 3.6 13.5
Turf Fertilizer 29-3-4 3.2 13.5
Ultra Turf Winterizer 22-3-14 3 12.0
Weed and Feed 3.2 13.5
Wal-Mart
Gardens Kentucky Bluegrass Grass
Seed
4 16.0
Gardens Kentucky Bluegrass Grass
Seed
2 13.5
Gardens Kentucky 31 Tall Fescue 8 18.0
Gardens Kentucky 31 Tall Fescue 4 16.0
Weed & Feed 28-3-3 3.2 13.5
APPLICATION RATE CHART
Media
lbs /
1000
square
feet
Flow
Control
Setting
at 3MPH
Generic Fertilizers
(if you don't have any other method)
1 12
2 13
3 14
4 15
5 17
6 18
7 19
8 20
9 22
10 24
Generic Grass Seed
(if you don't have any other method)
2 18
3 20
4 22
5 24

English Manual 1008066-E
16
The limited warranty set forth below is given by Brinly-Hardy
Company with respect to new merchandise purchased and
used in the United States, its possessions and territories.
Brinly-Hardy Company warrants the products listed below
against defects in material and workmanship, and will at its
option, repair or replace, free of charge, any part found to be
defective in materials or workmanship. This limited warranty
shall only apply if this product has been assembled, operated,
and maintained in accordance with the Operator’s manual
furnished with the product, and has not been subject to
misuse, abuse, commercial use, neglect, accident, improper
maintenance, alteration, vandalism, theft, fire, water, or
damage because of other peril or natural disaster.
Normal Wear Parts or components thereof are subject to
separate terms as follows: All normal wear parts or component
failures will be covered on the product for a period of 90 days.
Parts found to be defective within the warranty period will be
replaced at our expense. Our obligation under this warranty is
expressly limited to the replacement or repair, at our option, of
parts found to be defective in material and workmanship.
HOW TO OBTAIN SERVICE: Warranty parts replacements
are available, ONLY WITH PROOF OF PURCHASE, through
our Customer Service Department. Call 877-728-8224.
This limited warranty does not provide coverage in the following
cases:
a) Routine maintenance items such as lubricants and
filters.
b) Normal deterioration of the exterior finish due to
use or exposure.
c) Transportation and/or labor charges.
d) The warranty does not include commercial and/or
rental use.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose, applies
after the applicable period of express written warranty
above as to the part as identified below. No other express
warranty whether written or oral, except as mentioned
above, given by any person or entity, including a dealer
or retailer, with respect to any product, shall bind Brinly-
Hardy Co. During the period of the warranty, the exclusive
remedy is repair or replacement of the product as set forth
above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. Brinly-
Hardy Co. shall not be liable for incidental or consequential
loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services
or for rental expenses to temporarily replace a warranted
product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions or limitations
may not apply to you.
During the warranty period, the exclusive remedy is
replacement of the part. In no event shall recovery of any
kind be greater that the amount of the purchase price of the
product sold. Alteration of safety features of the product shall
void this warranty. You assume the risk and liability for loss,
damage, or injury to you and your property and/or to others
and their property arising out of the misuse or inability to use
this product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY:
This limited warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
IMPORTANT: The Warranty period stated below begins with
the PROOF OF PURCHASE. Without the proof of purchase,
the Warranty period begins from the date of manufacture
determined by the serial number manufacturing date.
SPREADER WARRANTY PERIOD: The warranty period
for this spreader is as follows: 1 year non-commercial use.
Tires and wheels are normal wear items: 90 days.
MANUFACTURER’S LIMITED WARRANTY FOR
BRINLY PULL-BEHIND ACCESSORIES
Brinly-Hardy Company • 3230 Industrial Parkway • Jeffersonville, IN 47130 • [phone] • brinly.com