BRIO 97HSA User manual

1
97HSA-_20
97HSA-_30
97HSA-_40
97HSA-_60
Required Hardware anodizing color not specified, items included in kits denoted with *
Preparing Wood Saddle and Rebate dimensions in mm[inches]
97HSA Preparation
97HSA Self Draining Sill
Brio Australia
P: [phone]
W:
E: [email protected]
brio.com.au
Brio UK
P: [phone]
W:
E: [email protected]
briouk.com
Brio USA
P: [phone]
W:
E: [email protected]
briousa.com
INST97HSA1 REV C- MAY 2015
*97HS57 Aluminum Extrusion
2, 3, 4 and 6m lengths supplied
*97EC End Caps
1 set supplied per kit
*94P Polypropylene Channel
2, 3, 4, and 6m lengths supplied
Cutting Wood Saddle
Available kits:
JW = Jamb Width
PT = Panel Thickness either 44.5[1.75] or 57.2[2.25]
Cut to length = W
Cut to length = W+2(JT)-6[0.24]
Seal AQ21 can be purchased
from Brio for the full perimeter seal
Cut 97HS57 & 94P to length = W+2(JT)-6[0.24]
Cut 97SR to length = W
97SR Rebate for 44.5[1.75] Panels
not supplied in kits
available in 2, 3, 4, and 6m
Notch 97HS57
each end
N = JT-3[0.12]
N
W
JT
3[0.12]
FIXED REBATE
W = Opening width between jambs
JT = Jamb Thickness
For 57.2[2.25] panels do not use 97SR and use rebate T1B
System Details
T1A
T1B
20.9
[0.83]
7.5
[0.30]
19.1[0.75]
13.4
[0.53]
XT and XT decided by installer12
XT1
6.4[0.25]
FIXED REBATE
Assembled Sill
wood not
supplied
52.7[2.08]
6[0.24]
PT
JW
31.8[1.25]
T1A
T2
121.6[4.79]
31.8
[1.25]
3.9[0.15]
25.4
[1.00]
11.9[0.47]
XT2
T2
11.9[0.47]

Preparing Sill Base
Assembling Sill use construction adhesives and sealants where recommended
Drill Ø3[0.12] to match fixing holes
2
Insert 94P into 97HS57 Drill hole Ø9.5[0.37]x90° at either end of sill for jamb fixings.
Fixing holes for wood T placed at 400[15.75] intervals (
2Ø9.5[0.37]x90°)
Screw Flutes
Apply adhesive to 97HS57’s grooves
and attach wood T2
Shape Jamb to match profile of 97HS57
Screw fix wood T to
97HS57
2
8G x 19[0.75] Screws Drill Ø3[0.12] to match jamb fixing holes
Attach 97EC - screws supplied
Attach jamb
to sill - apply
sealant to
screw heads
Frame can then
be fixed to
opening on-site
Wood T pinned in place last
1
Drill drainage hole through 94P and 97HS57 Ø8[0.32] and 2 holes through flush bolt recesses Ø5[0.20] each end
Ø9.5
[0.37]
90°
400
[15.75]
400
[15.75]
JT-6[0.24]
2
JT-6[0.24]
2T fixings2
Jamb fixings
NON-PIVOT
END
PIVOT
END
JT-3[0.12]
JT+80[3.15]
Ø8[0.32]
Ø5
[0.20]
Ø5
[0.20]
Drainage
holes not to
pierce sill’s
underside
JW
75°
XT +87[3.43]2
Ø3[0.12]
T2T2
44.5[1.75]
T1A
T2
57.2[2.25]
T1B
T2
97SR
JT-3[0.12]