BRIO WT50 -18/3 series User manual

1
Pack components
PACKS
55
53
56
53C
SP6X16Z
50G
50WR
50WR-S
50WR-C
WT50-18/3*
x1(1800)
x1(1800)
x1(1800)
x6
x30
x6
x6
WT50-21/3*
x1(2100)
x1(2100)
x1(2100)
x7
x33
x6
x6
WT50-24/3*
x1(2400)
x1(2400)
x1(2400)
x8
x36
x6
x6
WT50-27/3*
x1(2700)
x1(2700)
x1(2700)
x9
x41
x6
x6
WT50S-18/3*
x1(1800)
x1(1800)
x1(1800)
x6
x42
x6
x6
x6
x6
WT50S-21/3*
x1(2100)
x1(2100)
x1(2100)
x7
x45
x6
x6
x6
x6
WT50S-24/3*
x1(2400)
x1(2400)
x1(2400)
x8
x48
x6
x6
x6
x6
WT50S-27/3*
x1(2700)
x1(2700)
x1(2400)
x9
x50
x6
x6
x6
x6
Head and Sill Preparation head, sill and sill cover cut to length ‘W’ (finished opening width)
X X
400 400 400
No. 57
SILL WITH
No. 56
SILL
COVER
JAMB
257 21 No. 50WR-S
SOFT CLOSE
JAMB
Wardrobe Roll Trio 50kg
INSTBRIOWT502 REV C - AUG 2018
No. 50WR-C
SOFT CLOSE
CATCH
No. 50WR-S
SOFT CLOSE
No. 50G
GUIDE
No. 50WR
ROLLER
No. 53C
SILL COVER
CLIP
No. 56
SILL COVER
No. 58
HEAD GUIDE
No. 57
SILL
FINISHED OPENING
WIDTH (W)
JAMB
LINTEL
No. 58
HEAD GUIDE
JAMB
X X
400 400 400
X = 20
50SCT:
Screw fixings to be staggered along length, avoiding 257mm from ends of head guide if using soft close
PRE-DRILL AND
FIX PAN HEAD
SCREWS THROUGH
VEE GROOVE
35
20 MIN.
25 MAX.
No. 57
SILL
OPTIONAL SOFT CLOSE KIT
*Aluminium finishes: PWT = white powdercoat, CA = clear anodised
134.4
PANEL
THICKNESS
30 MIN.
40 MAX.
PANEL
HEIGHT
(PH)
No. 58
HEAD
GUIDE
134.4
3 MIN.
8 MAX.
9
No. 56
SILL COVER
No. 53C
SILL COVER CLIP
OPENING HEIGHT (H)=
PANEL HEIGHT (PH) + 37
Brio®
SP6X16Z
PAN HEAD
SCREWS
Allegion (New Zealand) Limited
P: [phone]
W: brionz.com
E: [email protected]

2
Panel preparation and hardware installation
Panel height = Opening height - 37mm
3 panels: Panel width = (Opening width / 3) + 20mm (overlap)
No. 57
SILL
OPENING WIDTH (W)
30mm
OVERLAP
3 PANEL CONFIGURATION
30mm
OVERLAP
JAMB JAMB
PANEL
WIDTH
(PW)
No. 50WR
WARDROBE
ROLLER
3.
1.
2.
Install panels as per numbered sequence below
45
DRILL Ø8
THROUGH
76
20
35
15
Machine slot and drill adjustment hole for No. 50WR Roller
C
L
No. 50G
GUIDE
170 15
15
PRE-
DRILL
Ø3 x 19
DEEP
Pre-drill holes for No. 50 Guide
Fitting soft close (optional)
Prepare panels for No. 50WR-C catch and No. 50G guide and fit components. Fit soft close into No. 55 head guide using fixings supplied.
Fitting panels
JAMB
1. SOFT CLOSE TO BE FITTED AGAINST JAMB
No. 58
HEAD GUIDE
JAMB
Soft close layout inside No. 58 head guide
A. B.
2. SCREW FIX
C.
A. B.
C. Catch of the
soft close faces
inward when
mounting
No. 50G
GUIDE
No. 50WR-C
CATCH
NOT PRIMED
PRIMED
C
L
170
15
15
DRILL Ø16.5
x 30 DEEP
PRE-
DRILL
Ø3 x 19
DEEP
C
L
JAMB
Prime soft
closes
before
installing
panels
Do not slide panel until rollers have been
adjusted down. Test panels.
OPTIONAL No. 50WR-S
SOFT CLOSE AND
No. 50WR-C CATCH
Adjust rollers up prior to installation.
1.
INSIDE
OUTSIDE
No. 50WR-C catch does not need to align
to No. 50WR-S soft close yet. Repeat the
process for the outside panel
3.
INSIDE
2.
INSIDE
1.
2.