Britax Safe-N-Sound BS3700A-C20133 Series User manual

Instructions for Installation & Use 1
IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED
ON THE CHILD RESTRAINT
Birth to 2-3 years (approx) REARWARD FACING
12 months to 4 years (approx) FORWARD FACING
INSTRUCTION MANUAL
CONVERTIBLE CHILD SEAT
Series No. BS3700A-C20133

Instructions for Installation & Use Instructions for Installation & Use
23
CHILD SEAT FEATURES - REARWARD FACING 18
SET UP
• GENERAL INFORMATION 20
• CONVERT TO REARWARD FACING 21
• INSTALLING INTO YOUR VEHICLE 22
• RECLINE ANGLE 24
• CLICKTIGHT 26
• TOP TETHER 30
• OPEN ADVANCED SIDE IMPACT CUSHION TECHNOLOGY 32
• HEADREST AND SHOULDER HARNESS 33
• REMOVE CHILD FROM CHILD SEAT 36
• REMOVE CHILD SEAT FROM VEHICLE 37
• STORE REBOUND BAR 39
• CLOSE ADVANCED SIDE IMPACT CUSHION TECHNOLOGY 39
CHILD SEAT FEATURES - FORWARD FACING 40
SET UP
• GENERAL INFORMATION 42
• FORWARD FACING RECLINE POSITIONS 43
• INSTALLING INTO YOUR VEHICLE 44
• CLICKTIGHT 46
• TOP TETHER 50
• HEADREST AND SHOULDER HARNESS 52
• OPEN ADVANCED SIDE IMPACT CUSHION TECHNOLOGY 55
• REMOVE CHILD FROM CHILD SEAT 56
• REMOVE CHILD SEAT FROM VEHICLE 57
• CLOSE ADVANCED SIDE IMPACT CUSHION TECHNOLOGY 59
QUICK START GUIDE - a shortened version of the manual
• REARWARD FACING 04
• FORWARD FACING 06
MEET YOUR CHILD SEAT 08
IMPORTANT INFORMATION AND WARNINGS 10
SHOULDER HEIGHT MARKERS 12
OUTGROWN YOUR CHILD SEAT 16
CHILD SEAT SUITABILITY GUIDE 17
REARWARD FACING
FORWARD FACING
CARE & MAINTENANCE
CONTENTS CONTENTS
CARE AND MAINTENANCE 60
• CLEAN HARNESS BUCKLE 61
• REMOVE COVER 62
• REPLACE COVER 64
ACCESSORIES 66
INSTALLATION OF VEHICLE UPPER ANCHOR POINT 69
IN CASE OF ACCIDENT 74
WARRANTY 76

Instructions for Installation & Use Instructions for Installation & Use
45
Harness
Straps
not below
green zone
QUICK START GUIDE - REARWARD FACING QUICK START GUIDE - REARWARD FACING
Store
strap
Pull
Press
Press
Attach
Pull
Remove slack
Lift
1
2
5
6
Remove slack
7
11
10 13
14
15 17 18
19
22
21
20 23
2624
27 29
25
28
12
16
8
9
3
4
Pull
Push
Remove
infant insert
Replace
infant insert
Push down
30
31
Hey, before you install me!
Don't forget to note your serial number found on the seat to complete your warranty registration.

Instructions for Installation & Use Instructions for Installation & Use
67
Harness
Straps
not below
green zone
Shoulder Level
25mm max
Pull
Press Store
strap
Attach
Pull
Remove slack
Remove
slack
7
6
10
3
8
9
5
Press
21
24 25
26
28
29
27
22
23
1311
12
14
16
17
18
20
19
QUICK START GUIDE - FORWARD FACING QUICK START GUIDE - FORWARD FACING
15
Pull
Push
Lift
Push down
Remove infant insert
1
2
4
Hey, before you install me!
Don't forget to note your serial number found on the seat to complete your warranty registration.

Instructions for Installation & Use Instructions for Installation & Use
89
REARWARD FACING-
To be used only in a rearward-facing position until the child's shoulders either reach the lower
shoulder height marker (approximately 12 months of age) or reach the middle height marker
(approximately 2 to 3 years of age).
FORWARD FACING-
Then to be used in a forward-facing position until the child's shoulders reach the upper
shoulder height marker (approximately 4 years of age).
Continue to use this child restraint until the child reaches this limit.
Do not use forward facing until child's shoulders are above the lower shoulder height marker.
Infants are at risk of serious injury if they face forward too early.
Children are at risk of serious injury if they move to booster seats too early.
Children who have outgrown this restraint are safest in a larger child restraint with an in-built
harness or a booster seat until their shoulders reach the upper shoulder height marker of the
restraint.
THE CLICKTIGHT SYSTEM
The CLICKTIGHT System makes installing your child seat easier in just a few steps. Your
child seat will be safe, secure and remain tightly fixed. It makes it seamless to change it from
rearward to forward facing or move it from one vehicle to install in another.
ADVANCED SIDE IMPACT CUSHION TECHNOLOGY™(SICT) PROTECTION
WHY DO I NEED ADVANCED SIDE IMPACT CUSHION TECHNOLOGY (SICT)?
In the event of an accident, your child must be optimally protected at any age, especially for
the most common types of accidents, frontal and side collision. With side collisions, children
are at most risk, because compared to a frontal collision, side collisions have less crumple
zone to disperse the energy released during impact.
WHAT IS IT?
Our Advanced SICT – Side Impact Cushion Technology with crumple zone feature is
designed to provide optimum safety to your child in the event of a side impact collision.
HOW DOES IT WORK?
With maximum safety and flexibility in mind, Advanced SICT can be used when the child seat
is positioned next to the vehicle door. When deployed, it is uniquely designed to enhance
protection in the event of a side impact collision. Combined with the energy absorbing
protective shell, Advanced SICT significantly reduces the risk of injury to your child.
THE ACTIVE HEADREST RESTRAINT (AHR)
The Active Headrest Restraint is designed with deeper side wings to shield and protect your
child's head in a side impact crash. The Active Head Restraint has an inner Side Impact
Cushion Technology layer which provides 180 degree protection around your child's head.
The AHR is adjustable to grow with your child and works in conjunction with SICT to protect
your child's head and minimise the force of impact.
To ensure that your child gets all the protection designed into the restraint PLEASE READ AND
FOLLOW THESE INSTRUCTIONS EXACTLY and use only Britax Safe-n-Sound recommended
parts and accessories.
If in doubt about the method of installation, consult Britax Childcare or agent, or a child
restraint fitter or, in New Zealand, to consult the agent for the vehicle.
只用于后向式安装，直到婴儿的肩膀达到靠下的肩高标记（大约12个月的宝宝）或者中部的肩高标
记（大约2-3岁的儿童）。然后用于前向式安装，直到儿童的肩膀达到靠上的肩高标记（大约4岁的儿
童）。
在儿童达到该座椅上限以前必须不断使用这一安全座椅。
在儿童肩高未超过靠下的肩高标记之前不得采用前向式坐姿。
婴儿过早乘坐前向式座椅则可能受到严重的伤害。
儿童过早使用垫高椅则可能受到严重的伤害。
个子比该安全座椅大的儿童最安全的做法是乘坐设有内置安全带的更大汽车座椅或垫高椅，直到他们
的肩膀达到该座椅靠上的肩高标记。
MEET YOUR CHILD SEAT MEET YOUR CHILD SEAT

Instructions for Installation & Use Instructions for Installation & Use
10 11
• Fit the restraint firmly to the car seat.
• Fit the harness firmly to the child.
• A loose restraint or harness is dangerous.
• Supervision of children is needed because they may be able to undo the buckles
and adjusters.
• Use the restraint exactly as shown in the instructions.
• DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR.
• Do not alter or modify this restraint.
• Repairs must only be done by the manufacturer or agent.
• Do not allow the restraint to come into contact with polishes, oils, bleach and other
chemicals.
• Destroy the restraint if it has been in a severe crash, even if no damage is visible.
See page 74 to 75.
• DO NOT USE THIS RESTRAINT WITHOUT THE COVER.
• Always secure the loose end of the top tether strap. Do not use the child restraint
where this top tether strap may fall into a split in the seat back or o the side of the
seat.
• ALWAYS ATTACH TOP TETHER HOOK AND REMOVE SLACK.
• To ensure infant’s back is evenly supported, do not put more than one nappy on the
baby and make sure the nappy is not thickly folded at the back.
• DO NOT USE A REAR-FACING CHILD RESTRAINT WHERE AN AIRBAG IS FITTED IN
FRONT OF THE SEATING POSITION.
• Do not harness an infant wrapped in a blanket or swaddled. Any blanket or wrap
must only be placed over the harness and infant.
• Without ISOFIX compatible connectors; This child restraint is not approved for use
with any connectors that connect to the car's ISOFIX low anchorages.
IMPORTANT :
IMPORTANT INFORMATION AND WARNINGS IMPORTANT INFORMATION AND WARNINGS
TO BE USED WITH A LAP-SASH OR LAP ONLY SEATBELT IN THE BACK OF MOST
CARS WITH FORWARD FACING SEATS.
GENERAL
• Babies and children below 4 years old must not sit in the front seat of a vehicle
unless allowable by the Regional Road Rules. Check your Regional Road Rules.
• Regularly check the restraint components, straps and other fitments for correct
function and condition. If faulty, cease using and seek repair by Britax.
• Protect all webbing from abrasion and cutting by sharp corners and edges.
• The restraint should not be purchased or sold as a second hand item. It is
recommended not to use child restraints older than 10 years as the protection in an
accident may be reduced.
• THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE TOP TETHER STRAP
MAY FALL INTO A SPLIT IN THE SEAT BACK OR OFF THE SIDE OF THE SEAT.
• Seatbelt extenders are not recommended to be used if the seatbelt is not long
enough to secure the child restraint. If seatbelts are too short then seek advice from
a child restraint fitter and consider their recommendations before using a seatbelt
extender. If you use a seatbelt extender then ensure that the seatbelt buckle does
not enter the rearward or forward facing belt paths.
• A rear facing child restraint should not be used in the front seat if a passenger airbag
is fitted and cannot be disabled.
• Rearward and forward facing child restraints should always be correctly installed,
properly adjusted and used as instructed by the manufacturer instructions.
• Ensure babies and toddlers are adequately shaded from direct sunlight through side
or rear windows.
• Check the car is ventilated by opening windows or using the car's ventilation system
taking in external air. Recirculation setting is not suitable for providing ventilation.
• THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT UPPER
ANCHORAGE POINT IN THE CAR. REFER TO CAR OWNER'S HANDBOOK FOR
LOCATION OF UPPER ANCHORAGE POINTS. REFER TO A CHILD RESTRAINT
FITTING STATION IF NO UPPER ANCHORAGE POINTS ARE IN THE MOTOR CAR.
Refer to pages 69 to 73.

Instructions for Installation & Use Instructions for Installation & Use
12 13
SHOULDER HEIGHT MARKERS SHOULDER HEIGHT MARKERS
Your child MUST be
forward facing if
their shoulders are
above the middle
marker.
If your child's shoulders are above the
upper marker they have outgrown the seat
(see page 16).
Your child can be
rearward facing
OR forward facing
if their shoulders are
between the lower
and middle marker.
Britax
recommends
using this restraint
in rearward
facing as long as
possible.
Your child MUST be
rearward facing if
their shoulders are
below lower marker.
Lower Height
Marker
Upper Height
Marker
Middle Height
Marker
Shoulder height markers are featured clearly on the child seat (as seen in diagram). The
markers provide an indicator for when your child has outgrown the child's seat rearward or
forward facing modes.

Instructions for Installation & Use Instructions for Installation & Use
14 15
SHOULDER HEIGHT MARKERS SHOULDER HEIGHT MARKERS
IMPORTANT: Follow this advice.
OR OR
Middle Height Marker
Lower Height Marker Middle Height
Marker
Lower Height
Marker
Lower Height Marker
Upper Height
Marker
Middle Height
Marker
Child Use (Forward Facing)
Older Baby (Rearward Facing) Older Baby (Forward Facing)
Newborn (Rearward Facing)

Instructions for Installation & Use Instructions for Installation & Use
16 17
When your child has outgrown this seat, you can use:
• Or a dedicated booster seat with vehicle lap-
sash seatbelt until 6 to 8 years of age or
until 8 to 10 years of age (or seatbelt and
compatible child harness).
• A convertible booster seat with in-built harness
until approximately 4 years old and then as
a booster seat with vehicle lap-sash seatbelt
until approx 6 to 8 years of age (or seatbelt
and compatible child harness).
• A harnessed child seat with in-built harness
suitable for children approximately 6
months to 8 years old.
OUTGROWN YOUR CHILD SEAT CHILD SEAT SUITABILITY GUIDE
CHILD SEAT SUITABILITY GUIDE
These child restraints, when used correctly, allow the driver to meet the Australian Road Rules
in each state.

Instructions for Installation & Use Instructions for Installation & Use
18 19
14
1. Adjustable Headrest
2. Shoulder Height Markers
3. Shoulder Pads (If supplied)
4. Infant Insert (If supplied)
5. Harness
6. EZ Buckle (If supplied)
7. Rebound Bar For Rearward Facing Mode
8. CLICKTIGHT Button
9. Harness Adjuster Button
10. Harness Adjuster Strap (lower)
11. Release Buckle (Red button)
12. Cover
13. Buckle Tongue Holders (If supplied)
14. Headrest Adjuster
5
4
3
2
6
11
12
1
22. Instruction Manual Location
23. Vehicle Seat Protector (If supplied)
24. Advanced Side Impact Cushion
Technology™ (SICT) (If supplied)
25. Top Tether Storage Pocket
26. Top Tether Adjuster
27. Top Tether Adjuster Strap
28. Top Tether
15. Vehicle's Anchor Fitting
16. Attachment Clip
17. REARWARD FACING BELT PATH (Blue)
18. Level Indicator
19. Grey Recline Lever
20. Blue Release Button
21. FORWARD FACING BELT PATH (Yellow)
22 21
24
27 28
26
25
7
Front of
vehicle
15
16
7
17
18
23
Long or short
Vehicle Seat
Protector
(If supplied)
9
10
8
13
19
20
CHILD SEAT FEATURES - REARWARD FACING CHILD SEAT FEATURES - REARWARD FACING

Instructions for Installation & Use Instructions for Installation & Use
20 21
IS THERE ENOUGH ROOM ?
To ensure that the space is sucient, the
purchaser should check the measurements
between the vehicle’s rear and front seats in
which the child restraint is intended to be used
for both rear facing mode and forward facing
mode.
DO NOT USE RESTRAINT IN REARWARD
FACING MODE WITHOUT THE REBOUND
BAR FULLY EXTENDED.
Do not use the restraint without the top
tether strap correctly attached.
DO NOT USE A REAR FACING CHILD
RESTRAINT WHERE AN AIRBAG IS FITTED
IN FRONT OF THE SEATING POSITION.
Do not use on any vehicle seat which faces
sideways or rearwards.
CHILD SEAT UPPER ANCHORAGE POINT
This child seat must be installed using the top tether. The top tether will need to attach to the
appropriate upper anchorage point for both rearward and forward facing modes. Refer to the
car owner's handbook for anchorage locations or points. If your vehicle does not have an
upper anchorage point then you will need to install an upper anchorage point. Refer to pages
69 to 73.
Do not allow the front seat to alter
the installed angle of the restraint.
CONVERT TO REARWARD FACING
MODE:
To fully recline the child seat,
Step 1. Squeeze the grey recline lever
upwards.
Step 2. Press the blue release button down
whilst squeezing the grey recline lever,
rotate the child seat to rearward facing
position.
Step 3. Align arrow to rearward facing image.
Step 1. Lift front flap in cover to access the
rebound bar.
Step 2. Pull out to full extension.
Step 3. Lift up to lock into position.
HOW TO SETUP THE REBOUND BAR:
1
2
SETUP - GENERAL INFORMATION
FOR REARWARD FACING SETUP - CONVERT TO REARWARD FACING
3
2
728mm
628mm
398mm
508mm
538mm
650mm
Width 467mm
3
REARWARD FACING
MEASUREMENTS
FORWARD
FACING
MEASUREMENTS

Instructions for Installation & Use Instructions for Installation & Use
22 23
SETUP - INSTALLING INTO YOUR VEHICLE
FOR REARWARD FACING
SETUP - INSTALLING INTO YOUR VEHICLE
FOR REARWARD FACING
Step 1. Press harness adjuster button.
Step 2. Place your hand under both shoulder
harness straps, then pull shoulder
harness straps to lengthen.
Step 3. Disengage buckle by pressing red
button.
Remove infant insert (if fitted).
Step 4. Place buckle tongues into buckle
tongue holders.
Choose the vehicle seat position.
Step 5. Ensure child seat is against vehicle
seatback - the rebound bar does not
need to contact vehicle seatback.
If desired, this gap may be packed
(see page 25).
Do not have the seat too far away from
the vehicle seat.
Step 6. Temporarily place top tether and
attachment clip over the back of child
seat.
INSTALLING INTO YOUR VEHICLE:
Top tether behind the child seat
1
2
6
5 5
4
Press
Pull
3Press

Instructions for Installation & Use Instructions for Installation & Use
24 25
Step 1. Check the level indicator (black ball) is
in required range.
The Rearward Facing Level Indicator shows
when your child seat is installed at the correct
angle for your vehicle. It gives you confidence
the child seat is positioned correctly whenever
you travel.
REARWARD FACING LEVEL
INDICATOR:
ANGULAR ADJUSTMENT OF
RESTRAINT
Some vehicle seats have more rearward slope
than others. The angle may be adjusted by
placing a firm packing between the child seat
and the underside of the base. Packing can be a
firmly rolled up towel (see figure A).
If the vehicle seat is flat then some packing may
be required at the front edge of the base to
achieve the recline angle (see figure B).
Always check that the rearward facing level
indicator confirms the correct installation angle for
rearward facing mode (see page 24).
SETUP - RECLINE ANGLE FOR REARWARD FACING SETUP - RECLINE ANGLE FOR REARWARD FACING
1
Black ball not visible
IMPORTANT:
This indicator should only be used in rearward
facing mode.
Figure .A.
Figure .B.
If the black ball is not visible, the child seat
angle may be adjusted by placing firm packing
between vehicle seat and base (see page 25).

Instructions for Installation & Use Instructions for Installation & Use
26 27
NOTE: Seatbelt extenders should not be used
if the seatbelt is not long enough to secure the
child restraint. If they are used then the buckle
must not enter the seating zone.
HOW TO INSTALL CLICKTIGHT:
Remove infant insert (if fitted).
IMPORTANT - Ensure buckle tongues are
placed into buckle tongue holders prior to
opening CLICKTIGHT frame.
Step 1. To open CLICKTIGHT frame, twist
and push the CLICKTIGHT button.
Allow frame to lift.
Step 2. Open CLICKTIGHT frame fully.
Step 3. Lengthen vehicle seatbelt.
Step 4. Feed vehicle seatbelt through blue
REARWARD FACING BELT PATH
guide, ensure the seatbelt is not
twisted during installation.
Step 5. Continue feeding vehicle seatbelt
through opposite blue REARWARD
FACING BELT PATH guide.
Step 6. Engage the vehicle seatbelt buckle
and tongue without twisting seatbelt.
ENSURE THERE ARE NO TWISTS IN
SEATBELT. REMOVE SLACK.
1
2
6
5
4
3
Lap
belt
Sash belt
VEHICLE SEATBELT
SETUP - CLICKTIGHT FOR REARWARD FACING SETUP - CLICKTIGHT FOR REARWARD FACING

Instructions for Installation & Use Instructions for Installation & Use
28 29
Step 7. Remove any slack from the vehicle
seatbelt.
Feed sash belt slack back into the
seatbelt retractor.
ALWAYS REMOVE SLACK FROM
SEATBELT.
Step 8. Always remove any excess shoulder/
lap straps, harness tongues and
harness adjuster strap (lower) that
may become trapped under the
CLICKTIGHT frame.
Step 9. Close CLICKTIGHT frame
Step 10. Press down until it locks into place.
If you need to apply excess force to
close the CLICKTIGHT frame, check
the shoulder/lap straps, harness
tongues and harness adjuster strap
(lower) are not trapped.
Step 11. Check if CLICKTIGHT frame is closed
by lifting the CLICKTIGHT FRAME up.
Your seat should feel secure.
Step 12. Refit infant insert as required.
You are now ready to install top tether.
Refer to page 30.
Lift
7
8
9
12
10
SETUP - CLICKTIGHT FOR REARWARD FACING SETUP - CLICKTIGHT FOR REARWARD FACING
ENSURE THERE ARE NO TWISTS IN
SEATBELT.
11
Push down
Pull

Instructions for Installation & Use Instructions for Installation & Use
30 31
HOW TO INSTALL THE TOP TETHER:
Step 1. Press top tether adjuster button and
Step 2. Lengthen top tether strap fully, ensure
all unnecessary twists are removed.
Step 3. Connect top tether attachment clip to
vehicle anchor fitting.
Step 4. Pull top tether strap slack onto side of
adjuster.
ENSURE THE TOP TETHER STRAPS ARE
NOT TWISTED.
Step 5. Ensure slack is removed from
the top tether straps by pulling
top tether adjuster strap.
Do not over tighten as it may cause
your child seat to lift.
ALWAYS REMOVE SLACK IN THE TOP
TETHER AND STORE STRAP.
Step 6. Check angle of child seat is still
correct.
Step 7. Roll up any excess strap and store in
the pocket provided on the top tether
strap.
CAUTION:
CHILDREN CAN BE INJURED OR RESTRAINTS AND TOP
TETHER STRAP DAMAGED BY UNSECURED CARGO IN A
COLLISION. SECURE OR REMOVE HAZARDOUS CARGO
BEFORE USING THIS CHILD RESTRAINT.
The top tether strap must be fitted at all times.
Always secure the loose end of the top tether strap to prevent it hanging out of the car or
being accessible by the child.
THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE TOP TETHER STRAP MAY
FALL INTO A SPLIT IN THE SEAT BACK OR OFF THE SIDE OF THE SEAT.
ALWAYS ATTACH TOP TETHER HOOK AND REMOVE SLACK IN THE TOP
TETHER STRAP.
IMPORTANT :
3
4
5
6
7
SETUP - TOP TETHER FOR REARWARD FACING SETUP - TOP TETHER FOR REARWARD FACING
1Press
Pull
Pull
Roll up
to store
2

Instructions for Installation & Use Instructions for Installation & Use
32 33
OPEN ADVANCED SIDE IMPACT
CUSHION TECHNOLOGY:
NOTE. The SICT system should not be
used if the child seat is in the centre
position.
For further information on SICT refer to
page 9.
Step 1. Rotate the SICT anti clockwise to full
extension on the preferred door side.
If at full extension the SICT makes
contact with the vehicle interior, reduce
the extension by rotating clockwise,
keeping it as close as possible to full
extension (finger clearance)
Step 2. Check the top tether route is above the
SICT and not below.
HOW TO USE - HEADREST AND
SHOULDER HARNESS:
Step 1. Press top tether adjuster button and
Step 2. Lengthen top tether strap fully (if
desired).
Step 3. Press harness adjuster button.
Step 4. Place your hand under both shoulder
harness straps, then pull shoulder
harness straps to lengthen.
Step 5. Disengage buckle by pressing red
button.
Step 6. Lift lever to adjust headrest/ harness
slots
3
4
Press
1
SETUP - OPEN ADVANCED SIDE IMPACT CUSHION
TECHNOLOGY FOR REARWARD FACING
SETUP - HEADREST AND SHOULDER HARNESS
FOR REARWARD FACING
Lift
6
5Press
Pull
1Press
Pull 2

Instructions for Installation & Use Instructions for Installation & Use
34 35
Step 8. Place baby into child seat. Ensure
baby is positioned with their back flat
against the back rest and their bottom
correctly positioned into the curved
seat base.
Step 9. Check headrest and shoulder slot
position is level with shoulders but not
below.
The shoulder straps must be in the
slots which are nearest to the child's
shoulders but not lower than the
child's shoulders.
Always adjust the height of the
shoulder straps as the child grows.
Flat
back
rest
Curved seat base
Step 10. Engage Buckle
ENSURE BUCKLE IS ALWAYS
CONNECTED DURING USE.
ENSURE ALL HARNESS STRAPS ARE
NOT TWISTED.
Step 11. Remove all slack from the lap strap
area (including behind baby's bottom),
by pulling up on the shoulder straps.
Step 12. Pull harness adjuster strap to tighten.
Ensure a firm but comfortable fit.
ENSURE ALL HARNESS SLACK IS
REMOVED.
Step 13. Remove slack from the top tether
straps by pulling top tether adjuster
strap.
Tongue
Buckle
Shoulder
Strap
Lap
strap
Do not harness an infant wrapped in a blanket or swaddled as this increases the risk of ejection
and injury or death in a crash. The harness needs to fit firmly to the baby, any blanket or other
covering may be placed over the harness after it is adjusted. Arms and legs must be free and not
bound or wrapped together. The legs must sit on each side of the crotch strap.
12
11
10
8
9
SETUP - HEADREST AND SHOULDER HARNESS
FOR REARWARD FACING
SETUP - HEADREST AND SHOULDER HARNESS
FOR REARWARD FACING
Above Shoulder Level
Harness Straps
not below
green zone
Step 7. Place buckle tongues into buckle
tongue holders.
Pull
WARNING: DO NOT LEAVE CHILDREN UNATTENDED
IN THE CAR.
7

Instructions for Installation & Use Instructions for Installation & Use
36 37
REMOVING CHILD FROM SEAT:
Step 1. Press top tether adjuster button and
Step 2. Lengthen top tether strap fully.
Step 3. Loosen shoulder harness straps by
pressing the harness adjuster button.
Step 4. Pull both shoulder harness straps
evenly.
Step 5. Disengage buckle by pressing red
button.
Step 6. Place harness buckles in buckle
tongue holder.
Step 7. Lift child from the child seat.
REMOVING CHILD SEAT FROM
VEHICLE:
Step 1. Press top tether adjuster button and
Step 2 . Lengthen top tether strap fully.
Step 3. Disconnect top tether attachment clip
from vehicle anchorage fitting.
Step 4. Disengage the vehicle seatbelt buckle.
3
4
6
3
4
Press
7
SETUP - REMOVE CHILD SEAT FROM VEHICLE
FOR REARWARD FACING
SETUP - REMOVE CHILD FROM CHILD SEAT
FOR REARWARD FACING
5Press
1Press
Pull 2
1Press
Pull 2

Instructions for Installation & Use Instructions for Installation & Use
38 39
Remove infant insert (if fitted).
IMPORTANT - Ensure buckle tongues are
placed into buckle tongue holders prior to
opening CLICKTIGHT frame.
Step 5. To open CLICKTIGHT frame, twist
and push the CLICKTIGHT button.
Allow frame to lift.
Step 6. Open CLICKTIGHT frame fully.
Step 7. Remove vehicle seatbelt from blue
REARWARD FACING BELT PATH.
Step 1. Press the grey release rebound bar
button to unlock the rebound bar.
Step 2. Store the rebound bar away.
Step 3. Ensure harness adjuster strap is not
under rebound bar.
Step 4. Re-attach the flap at the front of the
child seat.
NOTE: Remove any excess shoulder/
lap straps, harness tongues and
harness adjuster strap (lower) out from
under the CLICKTIGHT frame.
Step 5. Close CLICKTIGHT frame and press
down until it locks into place.
CLOSE ADVANCED SIDE IMPACT
CUSHION TECHNOLOGY :
Step 1. Rotate clockwise to close.
STORE REBOUND BAR:
67
1
2
3
4
5
1
SETUP - STORE REBOUND BAR
FOR REARWARD FACING
SETUP - REMOVE CHILD SEAT FROM VEHICLE
FOR REARWARD FACING
5
Push down