Brivo T1BVT4D User manual

T1BVT4D
4 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove1 enclosure with TBV1 Altronix/Brivo backplane
- One (1) Tango1B - PoE Driven Power Supply with
Lithium Battery Backup
- One (1) ACMS8CB - Dual Input PTC Access Power Controller
T1BV34SD
4 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove1 enclosure with TBV1 Altronix/Brivo backplane
- One (1) AL600ULXB - Power Supply/Charger
- One (1) ACM4CB - PTC Access Power Controller
- One (1) VR6 - Voltage Regulator
T2BV78SD
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TBV2 Altronix/Brivo backplane
- One (1) AL1024ULXB2 - Power Supply/Charger
- One (1) ACMS8CB - Dual Input PTC Access Power Controller
- One (1) PDS8CB - Dual Input PTC Power Distribution Module
- One (1) VR6 - Voltage Regulator
T2BV778SD
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TBV2 Altronix/Brivo backplane
- Two (2) AL1024ULXB2 - Power Supply/Chargers
- One (1) ACMS8CB - Dual Input PTC Access Power Controller
- One (1) PDS8CB - Dual Input PTC Power Distribution Module
- Two (2) VR6 - Voltage Regulators
T3BV7716SD
16 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove3 enclosure with TBV3 Altronix/Brivo backplane
- Two (2) AL1024ULXB2 - Power Supply/Chargers
- Two (2) ACMS8CB - Dual Input PTC Access Power Controllers
- Two (2) PDS8CB - Dual Input PTC Power Distribution Modules
- Two (2) VR6 - Voltage Regulators
- One (1) RSB2 - Rocker Switch Bracket with
Two (2) Rocker Switches (Not evaluated by UL)
Rev. TBVKD_110221
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners.
Installation Guide
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
Access & Power Integration

- 2 - Trove Brivo PTC ULXB Kits Installation Guide
Overview:
Altronix/Brivo Trove kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and
sub-assemblies. These kits also accommodate various combinations of Brivo boards for up to sixteen (16) doors in a single enclosure.
Configuration Chart:
Altronix
Model Number Input
Power
Supply
Board
Input
Fuse
Rating
Power
Supply
Board
Battery
Fuse
Rating
Maximum Supply
Current for Main and
Aux. Outputs on
Power Supply board and
ACM4/ACMS8 Access
Power Controllers’
outputs
Nominal
DC
Output
Voltage
Range
(VDC)
Fail-Safe/
Fail-Secure
or
Dry Form
“C”
Outputs Additional PTC Protected Outputs ACM4CB Board Input Fuse Rating ACM4CB Board Output PTC Rating ACMS8CB Board Output PTC Rating PD8S8CB Board Input PTC Rating PD8S8CB Board Output PTC Rating
T1BVT4D PoE
up to 90W N/A 10A/ 32V
12VDC @ 5A
24VDC @ 3A
20.17-
26.4 8 – – – 2.5A – –
T1BV34SD 115VAC 60Hz,
3.5A
5A/
250V N/A 24VDC @ 5.9A 20.17- 26.4 4 – 10A/ 32V 2.5A – – –
T2BV78SD 115VAC 60Hz,
4.2A
5A/
250V
15A/
32V 24VDC @ 9.4A 20.17- 26.4 8 8 – – 2.5A 9A 2.5A
T2BV778SD 115VAC 60Hz,
8.8A
5A/
250V
15A/
32V
24VDC @ 9.4A
+
24VDC @ 9.4A
20.17-
26.4 8 8 – – 2.5A 9A 2.5A
T3BV7716SD 115VAC 60Hz,
8.8A
5A/
250V
15A/
32V
24VDC @ 9.4A
+
24VDC @ 9.4A
20.17-
26.4 16 16 – – 2.5A 9A 2.5A
9.7-
13.2
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
If your application requires a raised backplane, re-mount it using metal spacers and screws (provided).
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.
Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the
enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring
to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.
4. Mount Brivo boards to backplane, refer to pages 3-7.
5. Refer to the Power Supply/Charger Installation Guide (Tango1B, AL600ULXB, AL1024ULXB2) and
corresponding Sub-Assembly Installation Guide (ACM4CB, ACMS8CB, PDS8CB, VR6) for
further installation instructions.
Fig. 1
Tamper Switch
(included)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure

Trove Brivo PTC ULXB Kits Installation Guide - 3 -
ACS6000 Main Board
ACS6000 Accessory Board
Altronix Tango1B is mounted under ACMS8CB
Altronix ACMS8CB
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
Fig. 2 - T1BVT4D Configurations
T1BVT4D: Configuration of Brivo Controls Boards:
1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 2, 2a, pg. 3).
Note: Brivo board must be properly grounded.
Please use provided metal spacers for the lower right mounting holes (Fig. 2, pg. 3).
3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 2a, pg. 3).
4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).
Pem
4/40 - 5/8”
Spacer
Brivo board Backplane
4/40 - 5/16”
Pan Head Screw
Fig. 2a

- 4 - Trove Brivo PTC ULXB Kits Installation Guide
ACS6000 Main Board
ACS6000 Accessory Board
Altronix
ACM4CB
TRG
TRIGGER
INPUT
ACM4
ACCESS POWER
CONTROLLER
LED1 LED2 LED3 LED4
MAIN
OUTPUT 1
NC C NO COM NC C NO COM NC C NO COM NC C NO COM
OUTPUT 2 OUTPUT 3
IN GND
1
IN GND
2
IN GND
3
IN GND
4
OUTPUT 4
-- +
CONTROL
-- +
POWER
+INP- T +RET-
INTERFACE
NO C NC
FACP
Altronix VR6 is mounted under ACM4CB
Altronix
AL600ULXB
+ DC ---
BAT FAIL NC C NO NC C NO
+ BAT ---
AC FAIL
DCAC BAT
LG N
5A 250V
OPEN --- 24V CLOSED --- 12V
To VR6 mounted under ACM4CB
12VDC
from VR6 output
Fig. 3 - T1BV34SD Configurations
T1BV34SD: Configuration of Brivo Controls Boards:
1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 3, 3a, pg. 4).
Note: Brivo board must be properly grounded.
Please use provided metal spacers for the lower right mounting holes (Fig. 3, pg. 4).
3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 3a, pg. 4).
4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).
Pem
4/40 - 5/8”
Spacer
Brivo board Backplane
4/40 - 5/16”
Pan Head Screw
Fig. 3a

Trove Brivo PTC ULXB Kits Installation Guide - 5 -
ACS6000 Main Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
Altronix VR6 is mounted under ACMS8CB
Altronix PDS8CB
Altronix ACMS8CB
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
+ INP1 --
OFF
IN1
IN2
Out1
<1 off 2>
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
PWR1 +
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
Fig. 4 - T2BV78SD Configurations
T2BV78SD: Configuration of Brivo Controls Boards:
1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 4, 4a, pg. 5).
Note: Brivo board must be properly grounded.
Please use provided metal spacers for the lower right mounting holes (Fig. 4, pg. 5).
3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 4a, pg. 5).
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Pem
4/40 - 5/8”
Spacer
Brivo board Backplane
4/40 - 5/16”
Pan Head Screw
Fig. 4a

- 6 - Trove Brivo PTC ULXB Kits Installation Guide
ACS6000 Main Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
Altronix VR6 is mounted under ACMS8CB
Altronix VR6 is mounted under PDS8CB
Altronix PDS8CB
+ INP1 --
OFF
IN1
IN2
Out1
<1 off 2>
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
PWR1 +
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
Altronix ACMS8CB
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
Fig. 5 - T2BV778SD Configurations
T2BV778SD: Configuration of Brivo Controls Boards:
1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 5, 5a, pg. 6).
Note: Brivo board must be properly grounded.
Please use provided metal spacers for the lower right mounting holes (Fig. 5, pg. 6).
3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 5a, pg. 6).
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Pem
4/40 - 5/8”
Spacer
Brivo board Backplane
4/40 - 5/16”
Pan Head Screw
Fig. 5a

Trove Brivo PTC ULXB Kits Installation Guide - 7 -
ACS6000 Main Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
ACS6000 Accessory Board
Altronix VR6 is mounted under ACMS8CB
Altronix PDS8CB
Altronix VR6 is mounted under ACMS8CB
Altronix PDS8CB
Altronix ACMS8CB
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
Altronix ACMS8CB
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
+ INP1 --
OFF
IN1
IN2
Out1
<1 off 2>
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
PWR1 +
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (---)
+ INP1 --
OFF
IN1
IN2
Out1
<1 off 2>
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
PWR1 +
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
Altronix
AL1024ULXB2
+ DC ---
BAT FAIL NC C NO NC C NO
--- BAT +
AC FAIL
DCAC BAT
LGN
5A 250V
RSB2
Fig. 6 - T3BV7716SD Configurations
T3BV7716SD: Configuration of Brivo Controls Boards:
1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 6, 6a, pg. 7).
Note: Brivo board must be properly grounded.
Please use provided metal spacers for the lower right mounting holes (Fig. 6, pg. 7).
3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 6a, pg. 7).
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Pem
4/40 - 5/8”
Spacer
Brivo board Backplane
4/40 - 5/16”
Pan Head Screw
Fig. 6b

- 8 - Trove Brivo PTC ULXB Kits Installation Guide
T1BVT4D and T1BV34SD (Trove1) Enclosure Dimensions (H x W x D approximate):
18” x 14.5” x 4.625” (457mm x 368mm x 118mm)
4.5” (114.3mm) 4.5” (114.3mm) 2.75”
(69.9mm)
1.115” (28.3mm)
1.36” (34.5mm)
1.25” (31.8mm) 1.25” (31.8mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
4.5” (114.3mm)
13.0” (330.2mm)
0.6” (15.2mm)
14.5” (321.3mm)
1.45” (36.8mm)
7.25” (184.2mm)
1.95” (49.5mm)
1.1” (27.9mm)
0.6” (15.2mm)
0.57” (14.5mm)
18.0” (457.2mm)
1.25” (31.8mm)

- 9 - Trove Brivo PTC ULXB Kits Installation Guide
T2BV78SD and T2BV778SD (Trove2) Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
6.75” (171.5mm)8.25” (209.5mm)
8.00” (203.2mm)
2.00” (50.8mm)
2.00” (50.8mm)
1.25” (31.8mm)
1.25” (31.8mm)
5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)
1.25” (31.8mm)
6.25” (158.8mm) 19.80” (502.9mm)
1.00” (25.4mm)
27” (685.8mm)
1.5”
(38.1mm)
2.00” (50.8mm) 2.00” (50.8mm)
3.5”(88.9mm) 3.5”(88.9mm)
21.50” (546.1mm)
5.25” (133.35mm) 5.25” (133.35mm)
6.25” (158.8mm)
1.25”
(31.8mm)
0.85” (21.6mm)
0.5625” (14.3mm)
2.415” (61.3mm)
0.685” (17.4mm)
1.77”
(45mm)
0.885” (22.5mm)
1.125” (28.3mm)
Knockouts
2.00” (50.8mm) 2.00” (50.8mm)

- 10 - Trove Brivo PTC ULXB Kits Installation Guide
T3BV7716SD (Trove3) Enclosure Dimensions (H x W x D approximate):
36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)
G
G
2”
(50.8mm)
8.75” (222.3mm) 8.75” (222.3mm)
8.62” (219mm)
7.06” (179.3mm)
1.25” (31.8mm)
1.25” (31.8mm)
2.00” (50.8mm) 7.12” (222.3mm) 9.5” (241.3mm) 9.5” (241.3mm)
30.12” (768.1mm)
14.01” (355.9mm) 14.01” (355.9mm)
1.25” (31.8mm) 1.55” (39.4mm)
1.78” (45.2mm)
1.25” (31.8mm)
1.07”
(27.2mm)
1.10” (27.9mm)
2” (50.8mm)
10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
2.00” (50.8mm)10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
36.12” (917.5mm) 33.63” (854.2mm)
3/4” Conduit
1” Conduit
1.75” Conduit
1.5” Conduit
1.75” Conduit
1.5” Conduit
3/4” Conduit
1” Conduit
3/4” Conduit
1” Conduit
3/4” Conduit
1” Conduit
3/4” Conduit
1” Conduit
2” Conduit

- 11 - Trove Brivo PTC ULXB Kits Installation Guide
Notes:

- 12 - Trove Brivo PTC ULXB Kits Installation Guide
Brivo Inc. is not responsible for any typographical errors.
7700 Old Georgetown Rd #300 | Bethesda, MD 20814 USA
phone: [phone] | email: [email protected] | www.brivo.com
IITrove Brivo PTC ULXB Kits K02U
Notes: