Brizo MultiChoice VETTIS T60288 User manual

91834 Rev. A
MultiChoice®Valve Trim
Installation Instructions
Owners Manual
Write purchased model number here.
Table of Contents:
Warranty ............................................................................... Page 2
Installation Instructions ......................................................... Pages 3 - 6
Maintenance ......................................................................... Page 7
Replacement Parts ............................................................... Page 9
1
You May Need
CAUTION: This system/device must be set by the
installer to ensure safe, maximum temperature.
Any change in the setting may raise the discharge
temperature above the limit considered safe and
may lead to hot water burns.
NOTICE TO INSTALLER: CAUTION!–As the
installer of this valve, it is your responsibility
to properly INSTALL and ADJUST this valve
per the instructions given. This valve does
not automatically adjust for inlet temperature
changes, therefore, someone must make the
necessary temperature knob adjustments at
the time of installation and further adjustments
may be necessary due to seasonal water
temperature change. YOU MUST inform the
owner/user of this requirement by following the
instructions. If you or the owner/user are unsure
how to properly make these adjustments, please
refer to page 7 and if still uncertain, call us at
1-877-345-BRIZO (2749).
After installation and adjustment, you must afx
your name, company name and the date you
adjusted the temperature knob to the caution label
provided and apply or attach the label to the back
side of the closest cabinet door and the warning
label to the water heater. Leave this Instruction
Sheet for the owner’s/user’s reference.
WARNING: This thermostatic bath valve is
designed to minimize the effects of outlet water
temperature changes due to inlet pressure and
temperature changes, commonly caused by
dishwashers, washing machines, toilets and
the like. It may not provide protection from hot
water burns when there is a failure of other
temperature controlling devices elsewhere
in the plumbing system, if the temperature
knob is not properly set or if the hot water
temperature is changed after the settings
are made or if the water inlet changes due to
seasonal changes.
WARNING: Do not install a shut-off device on
either outlet of this valve. When this type of
device shuts off the water ow, it can defeat
the ability of the valve to balance the hot and
cold water pressures.
For easy installation of your Brizo®faucet you
will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings,care, and
maintenance information.
2/16/17
1/32" 1/8"
91834
Models
T60088▲
T60288▲
Series
VETTIS™

91834 Rev. A
www.brizo.com
2
Limited Warranty on Brizo®Faucets
© 2017 Masco Corporation of Indiana
Cleaning and Care
Care should be given to the cleaning
of this product. Although its nish is
extremely durable, it can be damaged by
harsh abrasives or polish. To clean, simply
wipe gently with a damp cloth and blot dry
with a soft towel.
Parts and Finish
All parts (other than electronic parts and batteries) and finishes of this Brizo®faucet are warranted to the original con-
sumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser
owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Brizo®faucet are warranted to the original consumer purchaser to
be free from defects in material and workmanship for 5 years from the date of purchase or, for commercial users, for
one year from the date of purchase. No warranty is provided on batteries.
Brizo Kitchen & Bath Company will replace, FREE OF CHARGE, during the applicable warranty period, any part or
finish that proves defective in material and/or workmanship under normal installation, use and service. If repair or
replacement is not practical, Brizo Kitchen & Bath Company may elect to refund the purchase price in exchange for
the return of the product. These are your exclusive remedies.
Brizo Kitchen & Bath Company recommends using a professional plumber for all installation and repair. We also recom-
mend that you use only genuine Brizo®replacement parts.
Brizo Kitchen & Bath Company shall not be liable for any damage to the faucet resulting from misuse, abuse, neglect
or improper or incorrectly performed installation, maintenance or repair, including failure to follow the applicable care
and cleaning instructions.
Replacement parts may be obtained by calling the applicable number below or by writing to:
In the United States and Mexico: In Canada:
Brizo Kitchen & Bath Company Masco Canada Limited, Plumbing Group
Product Service Technical Service Centre
55 E. 111th Street 350 South Edgeware Road
Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1
1-877-345-BRIZO (2749) 1-877-345-BRIZO (2749)
[e-mail] [email protected]
Proof of purchase (original sales receipt) from the original purchaser must be made available to Brizo Kitchen & Bath
Company for all warranty claims unless the purchaser has registered the product with Brizo Kitchen & Bath Company.
This warranty applies only to Brizo®faucets manufactured after January 1, 1995 and installed in the United States of
America, Canada and Mexico.
BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES) FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THE FAUCET. Some states/provinces do not allow the exclusion or limitation of special, incidental
or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you special
legal rights. You may also have other rights which vary from state/province to state/province.
This is Brizo Kitchen & Bath Company’s exclusive written warranty and the warranty is not transferable.
If you have any questions or concerns regarding our warranty, please view our Warranty FAQs at www.brizo.com, email us
at [email protected] or call us at the applicable number above.

91834 Rev. A3
B.
1
4
4
2
3
60 Series Installation
1
Cartridge Installation
A.
Turn off water supplies. Remove cover (1),
bonnet nut (2), test cap (3) and plasterguard (4).
If screen (5) is in place, remove before installing
cartridge.
Plasterguard may be discarded.
1
2
3
4
Rotate the cartridge (1) so the word “UP” (2)
appears on the top. Insert cartridge into valve
body as shown. Make sure the cartridge tubes
and O-rings (3) are properly seated in holes at
the base of the body. Ensure the keys on the
body are fully engaged with the slots in the
body (4).
For back to back or reverse installations
(hot on right and cold on left): Rotate cartridge
(1) so the word “UP” (2) appears on the bottom.
Install the cartridge making sure that the keys are
fully engaged with the slots in the brass body (see
step B). Slide bonnet nut (3) over the cartridge
and thread onto the body. Hand tighten securely.
Slide bonnet nut (1) over the cartridge and
thread onto the body. Hand tighten securely.
C.
1
5
Back to back Installation
Normal Installation
(changes not required)
Reverse
Installation
Cold
Hot
1
3
2

91834 Rev. A 4
T60088 & T60288 Series Installation
2
Apply plumber tape to threads on brass adapter
(1). Install adapter so that it extends beyond
the nished wall 1-1/4" to 1-1/2". Ensure that
O-Rings (2) are installed properly into grooves
on adapter.
Slide shower ange (3) over shower arm (4).
Install shower arm (4) onto brass adapter (1),
and secure with set screw (5) on side of shower
arm. Slide ange (3) until it is at against the
nished wall.
Apply plumber tape to threads on shower arm
(4). Thread showerhead (6) onto shower arm.
Do not overtighten showerhead.
Showerhead Installation
(For Tub Spout installation refer to the installation guide provided with your tub spout)
3
Mounting Bracket Installation
Place bracket (1) against nished wall so that the
holes in legs of bracket align with threaded holes
on the rough.
Use two long screws provided to secure the
bracket to the rough. Do not overtighten screws.
Ensure that the bracket lays at against the
nished wall.
6
5
1
4
3
1
2

91834 Rev. A
5
Secure the escutcheon (4) to the bracket (5)
with the 2 screws provided (6).
Do not overtighten escutcheon screws.
Slide screw cover (7) over trim sleeve (3) and
press rmly until the cover is ush with escutcheon.
O-ring will hold screw cover in place.
Before installing volume control handle (8),
ensure valve is in the full cold position (clockwise).
Orient handle so the lever is pointing downward
(6 o’clock position) and press handle onto
cartridge. Secure handle with set screw provided
(9) and press button (10) into hole.
T60088 & T60288 Series Installation
D.
Slide O-ring (1) over cartridge and the bonnet
nut (2). The O-ring, which acts as a spacer to
steady the sleeve, should rest behind the
bonnet nut.
Note: Depending on location of valve within the
wall and wall thickness, an optional extension kit
may be needed. RP91022▲will provide up to
1-3/4" of extension.
Slide the sleeve (3) over the cartridge, body and
O-ring (1). Ensure sleeve is properly positioned
over the front of cartridge.
4
Valve Trim Installation
A.
12
B.
3
1
8
9
10
C.
4
5
6
7
3