Broil King SKFB2-1 User manual

Page 1
Dr o p -Do w n Sh e l f
St a t i o n a r y Si D e Sh e l f Ki t
re t a i n ow n e r ’SMa n u a l f o r fu t u r e re f e r e n c e .
SKSS2-1
SKFB2-1
SKFPB2-1

B101559-3-0611Page 2
iM p o r t a n t in f o r M a t i o n
Thank you for choosing a Broilmaster Premium Gas Grill. This shelf kit has been designed to t perfectly
and function awlessly – to provide years of service.
Please read the entire manual and compare the parts list to the parts provided with this kit before you
begin the installation. If this shelf kit is missing any parts, contact your Broilmaster dealer. Keep this
manual in a safe place to help you identify and order repair parts if they are ever required.
This manual covers the SKSS2 stationary shelf and the SKFPB2 and SKFB2 folding shelves. Refer to
the illustration for your shelf, and follow the instructions carefully.
NOTE: These side shelves are designed to support approximately 25 pounds. Exceeding this weight
limit may cause damage and void the warranty.
CAUTION: Parts may have sharp edges. Wear leather work gloves and handle parts carefully.
To order repair parts, contact your Broilmaster dealer. See the dealer locator at www.broilmaster.com.
When ordering parts, please have the following information available: Grill Model Number, Shelf Model
Number, Part Number and Description, and Quantity or Parts needed.
Tools Required
Phillips Screwdriver•
7/16-inch Socket and Ratchet or 7/16-inch Nut Driver•
B100770 PHILLIPS SCREW 10-16 X 1
B072217 PHILLIPS TRUSS HEAD SCREW 1/4-20 X 3/4
B076332 9/32 ID X 5/8 OD FLAT WASHER
B076331 1/4-20 HEX NUT
B076333 1/4 ID X 5/8 OD LOCK WASHER
SKfB2-1 & SKfpB2-1 ha r D w a r e pa c K a g e
co n t e n t S
B076330 HEX HEAD BOLT 1/4-20 X 1 1/2
B073978 TRUSS HEAD SCREW #10-24 X 1
B076332 FLAT WASHER 9/32 ID X 5/8 OD
B076331 HEX NUT 1/4-20
B076333 LOCK WASHER 1/4 ID X 5/8 OD
SKSS2-1 ha r D w a r e pa c K a g e co n t e n t S

B101559-3-0611 Page 3
St a t i o n a r y Si D e Sh e l f in S t a l l a t i o n
Stainless Steel Side Shelf
1. Remove the cooking grids, briquets and briquet rack from
the grill.
2. Attach the Handle Shelf Bracket to the grill using the Hex
Head Bolts, Flat Washers, Lock Washers, and Nuts. Do
not over-tighten.
3. Place the Tool Hook Bar inside the Shelf and place the
Shelf on the Bracket, aligning the screw hole. Insert the
Truss Head Screw and tighten. See Figure 1.
fi g u r e 1
Index No. Part No. Description
1 B076727 SIDE SHELF
2 B073971 TOOL HOOK
3 B101405 HANDLE SHELF BRACKET
B100002 HARDWARE PACKAGE
1
2
3
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact
Broilmaster Customer Service • w w w .broilmaster.com. To ensure prompt and accurate service, please provide the following
information when placing a repair part order: Model Number of your grill, Part Name, Part Number, and Quantity of parts
needed.
fi g u r e 2
Dr o p -Do w n Si D e Sh e l f in S t a l l a t i o n
3
2
1
4
5
Index
No.
Part No. Description
1 B100561 Side Shelf
2 B100568 Support Bracket Front - Stainless Steel
2 B100559 Support Bracket Front - Black
3 B100569 Support Bracket Back - Stainless Steel
3 B100560 Support Bracket - Back - Black
4 B101370 Bracket Attach Assembly
5 B100993 Shelf Support Stiffener

B101559-3-0611Page 4
Solid Surface Drop-Down Side Shelf
1. Remove the cooking grids, briquets and briquet rack from the grill.
2. Attach the Bracket Attach Assembly to the grill using the Truss Head Screws, Flat Washers, Lock Washers, and Nuts. See Figure 1.
Note: Ensure that the Bracket Attach Assembly is installed so that the match light access hole is on the bottom. See Figure 2
3. Place the Side Shelf upside down on a clean surface and use the four coarse-thread screws to loosely attach the Support Brackets.
4. Place the support stiffener on the inside of the shelf using (2) #10-16x1/2” screws to secure in place.
5. Hang the shelf brackets on the lower pins of the Bracket Attach Assembly. Tighten the four screws to secure the bracket arms to the
shelf. See Figure 3.
6. To raise the shelf - swing it out and lift the notches over the upper pins. Make sure the shelf is securely in position before placing any-
thing on it.
7. To lower the shelf - lift up on both brackets simultaneously and pull out slightly.
fi g u r e 1
fi g u r e 3
Dr o p -Do w n Si D e Sh e l f in S t a l l a t i o n
BROILMASTER®
A Division of Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Vi s i t o u r w e b s i t e a t w w w .broilmaster.com
If you have a general question about our products, please e-mail us at [email protected].
If you have a service or repair question, please contact your dealer.
Correct Bracket Alignment
Incorrect Bracket Alignment
fi g u r e 2