
4bromic.com/heat
IMPORTANT NOTES AND WARNINGS
WARNING
• IMPORTANT - Installation MUST be carried out by a licensed
and authorised person.
• DO NOT leave heaters ON unattended for prolong use and
inspect the heating space regularly.
• Improper installation, adjustment, or alteration and failure to
follow the warnings and instructions in this manual could result
in severe personal injury, death or property damage.
• The manufacturer is not responsible for any damage that could
happen from improper use. The manufacturer emphasises that
this appliance should be used in a responsible manner and that
all procedures, warnings, and safety instructions contained in
this booklet should be followed strictly.
• The installer is to ensure that the requirements of the local
authority, local electrical installation code, municipal building
codes, marine code, and any other relevant statutory
regulations are carried out.
• Do not place articles on or against this appliance.
• To reduce the risk of fire, do not store or use gasoline or other
flammable vapours and liquids in the vicinity of the heater.
• This Installation, Operation and Service manual should not be
removed from the site of installation. Installer should leave
manual with the customer for future reference.
• A minimum safety distance of 1000mm (39.4”) should always
be left in front of the appliance.
• The appliance must not be located directly below or in front
of an electrical socket. Heat radiated from the appliance may
damage the electricity outlet or plug if placed incorrectly.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Heaters shall NOT be installed in wardrobes or enclosed closets.
• Extreme caution is necessary when any heater is used by
or near children or invalids and whenever the heater is left
operating and unattended.
• Children and adults should be alerted to the hazards of high
surface temperatures and should stay away to avoid burns,
clothing ignition, or other serious personal injury
• This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, etc. and curtains
at least 3 feet (1m) from the front of the heater and keep them
away from the sides and rear
• Keep packaging materials out of reach of children
• Do not spray aerosols or flammable materials in the vicinity of
this appliance while it is in operation
• Installation and repair must be carried out by a qualified &
licenced service person only. The heater should be inspected
before use and at least annually serviced & inspected by a
qualified & licenced service person.
• Do not perform maintenance until heater has been turned o,
power disconnected, and heater temperature
has cooled to room temperature.
• Certain materials or items, when stored under or near the
appliance, will be subjected to radiant heat and could be
seriously damaged. Combustible materials eg. walls, floors,
furniture, fixtures and plants must be kept a minimum of
1000mm (3 ft) from the heater. Regularly inspect the heating
space for any materials or items that should not be near the
heater.
• Clothing or other flammable materials should not be hung from
the heater or placed on or near the heater.
• Be sure the heater is not facing the ceiling or flammable or
combustible substances/materials.
• This radiant heater shall NOT be installed on recreational vehicles.
• Do not attempt to alter the unit in any manner.
• This heater may be installed on suitably sized marine craft. When
such a marine installation is completed it is the sole responsibility
of the consumer, designer and marine installer to ensure the
application of the heater and installation complies with all
relevant electrical, fire and marine safety codes. Bromic accepts
no responsibility for the compliance, safety and suitability of any
such installation.
• Remove transit protection before use.
• Never operate the heater in an explosive environment such as
areas where petrol or other flammable liquids or vapours are
stored.
• Do not paint any surface of the heater.
• Check for damage to the appliance regularly. The heater must
not be used if the glass panel or any other part of the heater is
damaged. If damage to the appliance is suspected, discontinue
use immediately and contact the supplier or qualified person to
repair.
• After unpacking, make sure the appliance shows no signs of
visible damage or tampering. If the appliance appears damaged,
contact the place of purchase for assistance.
• This appliance must only be used on a 220-240V AC Single
phase power supply.
• Do not touch the heating glass surface at any time, even when
the heater is turned o and has cooled down.
• Do not touch the heater with wet hands at any time.
• If the appliance has not been used, or will not be used, for a long
period of time, disconnect power supply
• At the end of this product’s useful life, it must not be disposed
of as domestic waste, but must be taken to a collection
centre for waste electrical and electronic equipment. It is the
user’s responsibility to dispose of this appliance through the
appropriate channels at the end of its useful life. Failure to do
so may incur the penalties established by laws governing waste
disposal. Proper dierential collection, and the subsequent
recycling, processing and environmentally compatible disposal
of waste equipment avoids unnecessary damage to the
environment and possible related health risks, and also promotes
recycling of the materials used in the appliance. For further
information on waste collection and disposal, contact your local
waste disposal service, or the place of purchase.
• In case of direct connection to a supply line, for each platinum
Smart-Heat Electric heater, a two poles or double pole residual
current device (RCD), or residual circuit breaker (RCCB), must
be fitted upstream from the supply line; this electric wiring is
designed to quickly and automatically disconnect the appliance
when it detects that the electric current is not balanced between
the supply and return conductors to prevent electric shock.
• In case of direct connection to a supply line, for each Platinum
Smart Heat Electric heater, a bipolar circuit breaker (CB) with
contact opening distance of at least 3mm must be fitted
upstream from the supply line to protect from damage caused
by excess current from an overload or short circuit.
• Contact an authorized service technician if you are unsure if you
have RCD and CB installed on the premises.
• Do not install the heater directly near a bathtub, shower or
swimming pool. Any switches or controls must not be within
reach of a person in the bathtub, shower or swimming pool.
• To maintain Ingress Protection Rating (IP56), only IP56 rated,
electrical components such as, switches and conduit fittings
must be used for electrical installation.
• This product does not have a switch for electrical disconnection.