Bromic Heating platinum Smart-heat Troubleshooting guide

Version 1.1 EU
PLATINUM SMART-HEAT™
ELECTRIC HEATER
BY BROMIC
INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
AVAILABLE IN 1500W VERSION
IMPORTANT
READ THIS MANUAL CAREFULLY.
SEE INSIDE COVER FOR IMPORTANT INFORMATION
ABOUT THIS MANUAL.KEEP INSTRUCTION WITH
APPLIANCE FOR FUTURE REFERENCE.
!
APPAREIL DE CHAUFFAGE ÉLECTRIQUE
PLATINUM SMART-HEAT™
PAR BROMIC
MANUEL D’INSTALLATION, D’INSTRUCTION ET D’ENTRETIEN
DISPONIBLE EN VERSION 1500W
PLATINUM SMART-HEAT™
SISTEMA DI RISCALDAMENTO ELETTRICO
DI BROMIC
MANUALE DI INSTALLAZIONE, FUNZIONAMENTO E MANUTENZIONE
DISPONIBILE NELLA VERSIONE DA 1500W
PLATINUM SMART-HEAT™
ELEKTRISCHES HEIZGERÄT
VON BROMIC
INSTALLATIONS-, ANWEISUNGS - UND WARTUNGSANLEITUNG
IN 1500W-VERSION ERHÄLTLICH
PLATINUM SMART-HEAT™
CALEFACTOR ELÉCTRICO
DE BROMIC
MANUAL DE INSTALACIÓN, INSTRUCCIONES Y REVISIÓN
DISPONIBLE EN VERSIÓN DE 1500 W

Installation, instruction and service manual English version..................................... 3 - 15
Traduction Manuel d’installation, d’instruction et de services en français............. 17 - 29
Installazione, istruzione e servizio di traduzione manuale in lingua italiana......... 31 - 43
Installation, Einweisung und Service-Handbuch Deutsch Übersetzung................. 45 - 57
Instalación, instrucciones y manual en español.......................................................... 59 -71
Contents / Contenu / Contenuto / Inhalt / Contenido

Version 1.1 EU
PLATINUM SMART-HEAT™
ELECTRIC HEATER
BY BROMIC
INSTALLATION, INSTRUCTION AND
SERVICE MANUAL
AVAILABLE IN 1500W VERSION
IMPORTANT
READ THIS MANUAL CAREFULLY.
SEE INSIDE COVER FOR IMPORTANT INFORMATION
ABOUT THIS MANUAL.KEEP INSTRUCTION WITH
APPLIANCE FOR FUTURE REFERENCE.
!

4www.bromicheating.com
!
IMPORTANT
This manual contains important information about the installation, operation, and maintenance
of Platinum Smart-Heat™ Electric Heaters. Please pay close attention to the important safety
information shown throughout this instruction manual. Any safety information will be accompanied
by the following safety alert symbols:
DANGER, WARNING, IMPORTANT
•READ THIS MANUAL CAREFULLY before installing or
servicing this product.
•Improper installation, operation, or maintenance can result in
death, severe injury, or property damage.
•This appliance is intended for fixed installation with 220-240V
AC Single phase power supply
•Installation MUST be carried out by a licensed and authorised
technician in accordance with local electrical codes.
!
!
!
Head Office: 10 Phiney Place Ingleburn NSW 3565 Australia
Telephone: [phone] (within Australia) or [phone] (from overseas)
Email: [email protected] Web: www.bromicheating.com
Note: Bromic Pty Ltd reserves the right to make changes to specifications, parts, components and equipment without prior notification.
This Installation, operation and service manual may not be reproduced in any form without prior written consent from Bromic Pty Ltd.
Correct Disposal of this product
This marking indicates that this product should not
be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device,
please use the return and collection systems or contact
the retailer where the product was purchased. They
can take this product for environmental safe recycling.

5
www.bromicheating.com
CONTENTS
IMPORTANT NOTES & WARNINGS 4
PRODUCT OVERVIEW 5
PRODUCT DESCRIPTION 5
SPECIFICATIONS 5
PRODUCT FEATURES 5
HEATER INSTALLATION INSTRUCTIONS 6
CEILING & WALL MOUNTING 6
CEILING RECESS 8
UMBRELLA MOUNTING 9
TUBE SUSPENSION 10
CHAIN SUSPENSION 11
ELECTRICAL INSTALLATION 12
SERVICING 12
REPLACEMENT PART LIST 13
TROUBLESHOOTING 13

6www.bromicheating.com
IMPORTANT NOTES AND WARNINGS
WARNING
•IMPORTANT - Installation MUST be carried out by a
licensed and authorised person.
•Improper installation, adjustment, or alteration and
Failure to follow the warnings and instructions in this
manual could result in severe personal injury, death or
property damage.
•The manufacturer is not responsible for any damage
that could happen from improper use. The manufacturer
emphasises that this appliance should be used in a
responsible manner and that all procedures, warnings,
and safety instructions contained in this booklet be
followed strictly.
•The installer is to ensure that the requirements of the
local authority, local electrical installation code, municipal
building codes, and any other relevant statutory
regulations are carried out.
•Do not place articles on or against this appliance.
•Do not use or store flammable materials near this
appliance
•This Installation, Operation and Service manual should
not be removed from the site of installation. Installer
should leave manual with the customer for future
reference.
•A minimum safety distance of 1000mm should always be
left in front of the appliance.
•This unit must be mounted at a minimum of 1800 mm
above the floor.
•The appliance must not be located directly below or in
front of a wall electricity socket. This is because the heat
radiated from the appliance may damage the electricity
outlet or plug.
•Any guard or other protective device removed for
servicing (conducted by an authorised person) must be
replaced before operating the heater.
•This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
•Heaters are not intended to be installed in wardrobes.
•Children should be carefully supervised when they are in
the area of the heater.
•Children and adults should be alerted to the hazards of
high surface temperatures and should stay away to avoid
burns, clothing ignition, or other serious personal injury
•Keep packaging materials out of reach of children
•Do not spray aerosols or flammable materials in the
vincinty of this appliance while it is in operation
•Installation and repair must be carried out by a qualified
& licenced service person only. The heater should be
inspected before use and at least annually serviced &
inspected by a qualified & licenced service person.
•Do not perform maintenance until heater has been
turned off, power disconnected, and heater temperature
has cooled to room temperature.
•Certain materials or items, when stored under or near
the appliance, will be subjected to radiant heat and
could be seriously damaged. Combustible materials eg.
walls, floors, furniture, fixtures and plants must be kept a
minimum of 1000mm from the heater.
•Clothing or other flammable materials should not be
hung from the heater or placed on or near the heater.
•Be sure the heater is not facing the ceiling or flammable
or combustible substances/materials.
•This radiant heater is NOT intended to be installed on
recreational vehicles and/or boats.
•Do not attempt to alter the unit in any manner.
•Remove transit protection before use.
•Never operate the heater in an explosive environment
such as areas where petrol or other flammable liquids or
vapours are stored.
•Do not paint any surface of the heater.
•Check for damage to the appliance regularly. The heater
must not be used if the black radiant panel or any other
part of the heater is damaged. If damage to the appliance
is suspected, discontinue use immediately and contact
the supplier or qualified person to repair.
•After unpacking, make sure the appliance shows no signs
of visible damage or tampering. If the appliance appears
damaged, contact the place of purchase for assistance.
•This appliance must only be used on a 220-240V AC
Single phase power supply.
•Do not touch the heating surface at any time, even when
the heater is turned off and has cooled down.
•Do not touch the heater with wet hands at any time.
•If the appliance has not been used, or will not be used,
for a long period of time, disconnect power supply
•At the end of this product’s useful life, it must not be
disposed of as domestic waste, but must be taken to
a collection centre for waste electrical and electronic
equipment. It is the user’s responsibility to dispose of this
appliance through the appropriate channels at the end
of its useful life. Failure to do so may incur the penalties
established by laws governing waste disposal. Proper
differential collection, and the subsequent recycling,
processing and environmentally compatible disposal of
waste equipment avoids unnecessary damage to the
environment and possible related health risks, and also
promotes recycling of the materials used in the appliance.
For further information on waste collection and disposal,
contact your local waste disposal service, or the place of
purchase.
!

7
www.bromicheating.com
• In case of direct connection to a supply line, a bipolar circuit
breaker with contact opening distance of at least 3mm
must be fitted upstream from the supply line. Contact an
authorised service technician if you are unsure if you have a
circuit breaker installed on the premises.
• Do not install the heater directly near a bathtub, shower
or swimming pool. Any switches or controls must not
be within reach of a person in the bathtub, shower or
swimming pool.
• To maintain Ingress Protection Rating (IPX5), only IP55
rated conduit fittings should be used for electrical
installation.
• A means for disconnection of the heater must be
incorporated in the fixed wiring according to the local
electrical codes.
• If the supply cord is damaged, it must be replaced by
an authorised and licenced person in order to avoid a
hazard.
The Platinum Smart-Heat™ Electric is designed to provide
efficient spot heating for commercial and residential
applications. The non-glowing black radiant surface of the
heater provides a comfortable heat without interfering with
the atmosphere created by your venue.
PRODUCT OVERVIEW
IMPORTANT NOTES AND WARNINGS CONTINUED ...
SPECIFICATIONS
Model 1500W
Part no. BH0320001
Heat Output (Watts) 1500W
Power connection required (Volts/Amps) 220-240V - a.c. - 50/60Hz / 6.5 Amps
Dimensions (WxHxDmm) 960 x 162 x 40mm
Weight (kg) 6.2kg
Finish High-temperature Coating
Approval CE Approved
PRODUCT FEATURES
The heaters are built with corrosion resistant materials,
have electrical approval and are rated to IPX5 water Ingress
Protection. Making the Platinum Smart-Heat™ Electric the
perfect solution for a variety of indoor and outdoor heating
applications.
▪Ultra-thin and stylish design
▪Non-glowing — does not interfere with the atmosphere
created by your venue or environment.
▪Efficient directional spot heating.
▪Heat Zones — one or more heaters can be switched on and
off simultaneously from a single remote-located switch.
▪Platinum Smart-Heat™ Electric Heaters can also be
integrated into smart control systems.
▪Wind resistant & IPX5 water protection rating.
▪Suitable for outdoor and indoor heating applications
such as restaurants, cafes, bars and clubs, factories, office
spaces, designated smoking areas, public areas, hotels and
more.
▪Standard Mounting - included with heater.
▪Optional Mounting - purchased separately from heater:
▪Umbrella Mounting
▪Ceiling Recess
▪Tube Suspension
▪Chain Suspension

8www.bromicheating.com
!
WARNING
This heater MUST be permanently installed by
an authorised/licenced person. Do not perform
maintenance, or carry out installation or assembly
procedure while electrical power is switched on.
2200
1601800 250
WALL MOUNTING
CEILING
FLOOR
250
2400 180
2580
CEILING MOUNTING
CEILING
FLOOR
HEATING INSTALLATION INSTRUCTIONS
1. Heater must be installed with the minimum installation
clearances shown in diagram.
Minimum distance between heaters measured from
edge of heaters must be at least 500mm.
CEILING & WALL MOUNTING BRACKETS
Minimum distance from edge of the heater to any
adjacent walls must be at least 250mm. Heater must be
away from the fourth wall.
During installation the supply cord should be
positioned such that it exits from the nearest edge
of the heater and not from the centre or across the
heater.
!
WARNING - Outdoor Installation
For longest product life & to maintain product
appearance mount heater under cover & protect
from rain & weather whenever possible.

9
www.bromicheating.com
HEATING INSTALLATION INSTRUCTIONS CONTINUED...
2. Mark mounting hole centres on ceiling or wall. Brackets
have 2 different mounting holes options.
3. Attach mounting brackets to ceiling or wall using
appropriate fasteners (Not supplied).
4. Assemble rear brackets to heater with M5 screws.
5. Bring heater up to mounting brackets and lock into
position with M5 screw & nut.
6. Rotate heater to required angle. 15° or 30° in either
direction. Lock into position with M5 screw & nut.
7. Make electrical connection from heater to power
supply.
438
30
960
453
67.5
Mounting Hole Centres
& Heater Position
2
4
3
7
6
5

10 www.bromicheating.com
5
6
2
3
4
1008
210
Ceiling Cut Out
1
Ceiling Recess
Instructions below are suitable for ceiling
surfaces 10-30mm thick. For ceiling surfaces
thicker than 30mm contact Bromic for
alternative installation options.
Minimum distance from perforated rear cover
to ceiling must be 150mm.
This space behind the heater must be kept clear
to allow ventilation.
(1) Prepare ceiling cut out.
(2) Put ceiling support brackets in position
(3) From below, bring ceiling frame up and into
ceiling cut out.
(4) Fasten ceiling frame in position with M4x10
screws & nyloc nuts. Which locator hole to use
is dictated by thickness of ceiling surface.
(5) Assemble rear mounting brackets to heater
with M4x10 screws.
(6) Feed power cord through hole in perforated
rear cover.
(7) Attach perforated rear cover to rear
mounting brackets with 8Gx10mm self-tapping
screws.
Confirm final steps after prototype testing.
Raise one side of Platinum Electric up into
ceiling frame cavity & hook over Ceiling frame.
Push Platinum Electric against the frame & raise
other side of heater over ceiling frame.
Ensure all four rear mounting brackets are
hooked over the ceiling frame & centre the
Platinum Electric inside the Ceiling frame.
The heater shall, under no circumstance, be
covered with insulating material or similar
material.
Joists, beamsand rafters shall not be cut or
notched to install the heater.
5
6
2
3
4
1008
210
Ceiling Cut Out
1
Ceiling Recess
Instructions below are suitable for ceiling
surfaces 10-30mm thick. For ceiling surfaces
thicker than 30mm contact Bromic for
alternative installation options.
Minimum distance from perforated rear cover
to ceiling must be 150mm.
This space behind the heater must be kept clear
to allow ventilation.
(1) Prepare ceiling cut out.
(2) Put ceiling support brackets in position
(3) From below, bring ceiling frame up and into
ceiling cut out.
(4) Fasten ceiling frame in position with M4x10
screws & nyloc nuts. Which locator hole to use
is dictated by thickness of ceiling surface.
(5) Assemble rear mounting brackets to heater
with M4x10 screws.
(6) Feed power cord through hole in perforated
rear cover.
(7) Attach perforated rear cover to rear
mounting brackets with 8Gx10mm self-tapping
screws.
Confirm final steps after prototype testing.
Raise one side of Platinum Electric up into
ceiling frame cavity & hook over Ceiling frame.
Push Platinum Electric against the frame & raise
other side of heater over ceiling frame.
Ensure all four rear mounting brackets are
hooked over the ceiling frame & centre the
Platinum Electric inside the Ceiling frame.
The heater shall, under no circumstance, be
covered with insulating material or similar
material.
Joists, beamsand rafters shall not be cut or
notched to install the heater.
CEILING RECESS (SOLD SEPARATELY)
WARNING
Instructions below are suitable for ceiling surfaces 10-
30mm thick. For ceiling surfaces
thicker than 30mm contact Bromic for alternative
installation options.
!
!
WARNING
Minimum vertical ceiling space clearance measured from
ceiling surface must be 300mm.
Minimum horizontal ceiling space clearance measured
from each edge of ceiling cut out must be 500mm.
Minimum distance between heaters measured from edge
of ceiling cut out must be 500mm.
!
WARNING
The heater shall, under no circumstance, be covered with
insulating material or similar material.
During installation the supply cord should be positioned
such that it exits from the nearest edge of the heater
and not from the centre or across the heater
!
WARNING
Joists, beams and rafters shall not be cut or notched to
install the heater.
1008
210
Ceiling Cut Out
1
2
3
4
HEATING INSTALLATION INSTRUCTIONS CONTINUED...
1. Prepare ceiling cut out. Heater must be installed with
heater surface at least 2400mm above the floor level.
2. Put ceiling support brackets in position.
3. From below, bring ceiling frame up and into ceiling cut
out.
4. Fasten ceiling frame to ceiling support brackets with
M5 screws & nyloc nuts. Which locator hole to use is
dictated by thickness of ceiling surface.
5. Screw hex spacers into 4 mounting holes. Spacers
must be assembled between heater & rear mounting
brackets.
6. Assemble rear mounting brackets to spacers with M5
screws.
7. Raise one side of heater up into ceiling frame cavity &
then raise whole heater into cavity.
8. Rotate the heater into horizontal position in the ceiling
cavity & then lower down onto the ceiling frame.
9. Ensure all four rear mounting brackets are hooked over
the ceiling frame & centre the heater inside the frame.
10. Make electrical connection from heater to power
supply.

11
www.bromicheating.com
HEATING INSTALLATION INSTRUCTIONS CONTINUED...
1. Heater must only be mounted on metal umbrella arms.
Heater must be installed with heater surface at
least 2400mm above the floor level.
Drill mounting holes in umbrella arm.
2 x Ø6.0mm holes through both sides of arm.
1 x Ø25.0mm hole through bottom of arm only.
Ø25.0mm hole must be positioned at the end of
umbrella arm leading to power supply.
2. Attach bracket to umbrella arm with M5 bolts, washers
and nyloc nuts.
Supplied bolt suits umbrella arm up to Ø30.0mm.
3. Assemble heater bracket to heater with M5 screws.
4. Bring heater up to umbrella arm & feed power cable
into power cable hole.
5. Position heater against umbrella arm with heater
bracket channel on the inside of umbrella bracket
channel. Lock into place with self tapping screws 4
places.
6. Make electrical connection from heater to umbrella.
power supply.
117 500
25
6
230
960
162
Heater position relative
to mounting holes
Mounting Holes
1
2
3
4
5
6
UMBRELLA MOUNTING (SOLD SEPARATELY)
Minimum size of pole must be Ø30mm
Mounting pole material must be rated minimum 200°C.
Minimum distance from edge of the heater to any
adjacent surfaces must be 250mm.
Minimum distance from front surface of heater to
surface behind heater must be 180mm.
Any surface/material behind the heater, less than 180mm
from the front surface of the heater, must be rated
minimum 140°C. Surface/material must be positioned to
ensure no contact with mounting pole or surfaces of the
heater.

12 www.bromicheating.com
HEATING INSTALLATION INSTRUCTIONS CONTINUED...
TUBE SUSPENSION (SOLD SEPARATELY)
600
960
1
20
10
6.5
Suspension Tube
Mounting Hole
2
5
3
6
4
13
11
12
7
10
14
89
1. Heater must be installed with heater surface at least
2400mm above the floor level.
Supplied suspension tubes position heater surface
1000mm below the ceiling surface.
If required, cut down length of suspension tubes to
ensure correct installation height.
Minimum distance from front surface of heater to
ceiling surface must be 180mm.
Minimum distance between heaters measured from
edge of heaters must be at least 500mm.
2. If suspension tubes are cut down, drill new mounting
holes in each tube.
3. Feed power cord through hole in rear bracket and
suspension tube.
4. Attach rear bracket to heater with M5 screws.
5. Assemble suspension tubes to rear bracket with M5
screw and nut.
6. Rotate heater to required angle. 15° or 30° in either
direction. Lock into position with M3 screw and nut.
7. Slide ceiling bracket cover over suspension tubes.
8. Assemble supplied rubber grommets in ceiling bracket
to protect power supply cables.
9. Bring ceiling bracket to suspension tubes & feed
power cord through required hole in ceiling
bracket supports. Note: Which hole to feed
power cord through is defined by where the power
is brough into the ceiling bracket in Step 12.
Locate suspension tubes inside ceiling bracket supports.
10. M5 bolts through ceiling bracket supports &suspension
tubes. Secure with nyloc nuts.
11. Raise heater assembly into position. Attach ceiling
bracket to surface through mounting holes with
appropriate fasteners (Not supplied).
12. Bring power into ceiling bracket through ceiling
access holes or side access holes. Use minimum
IP55 rated cable gland in the Ø16mm holes.
If side access holes are not used, assemble supplied
hole plugs.
13. Make electrical connection from suspension tube power
cord to power from ceiling.
14. Slide ceiling bracket cover up suspension tubes into
position. Secure with self tapping screws.

13
www.bromicheating.com
1. Heater must be installed with heater surface at least
2400mm above the floor level. If required, cut down
length of chain to ensure correct installation height.
Minimum distance between heaters measured from
edge of heaters must be at least 500mm.
Minimum distance from front surface of heater to
ceiling surface must be at least 180mm.
2. Feed power cord through hole in rear bracket.
3. Attach rear bracket to heater with M5x10 screws.
4. Attach chains to heater with “S” hooks. Crimp “S”
hooks closed after assembly.
5. Prepare ceiling structure for heater. Attach chains to
ceiling structure & suspend heater.
6. Fix heater power cord to ceiling chain with cable ties.
7. Make electrical connection from heater to power
supply.
CHAIN SUSPENSION (SOLD SEPARATELY)
960
417
1
2
3
4
5
6
7
HEATING INSTALLATION INSTRUCTIONS CONTINUED...

14 www.bromicheating.com
ELECTRICAL INSTALLATION
!
WARNING
This heater MUST be permanently installed by
an authorised/licenced person. Do not perform
maintenance, or carry out installation or assembly
procedure while electrical power is switched on.
1. Check product label for correct voltage and wattage
- Make sure power source conforms to the heaters
requirements.
2. Use appropriate power supply cables for the heaters’
voltage and wattage with minimum temperature rating
of 105°C. The fixed wiring must be positioned away
from & protected from the enclosure of the heater.
3. Make all connections in accordance with local
electrical code regulations. For outdoor installation all
connections must be made in accordance with local
electrical code regulations for outdoor wiring. Only
use wiring components approved for outdoor use with
minimum IPX5 rating.
WARNING
ELECTRICAL SHOCK HAZARD! Serious injury or death
may occur. Disconnect from electrical supply before
installing or servicing this heater. Read and follow
installation clearance requirements outlined in this
manual. The appliance MUST be connected to a properly
grounded electrical source.
!
ELECTRICAL INSTALLATION
WARNING
ELECTRICAL SHOCK HAZARD!
Serious injury or death may occur.
Disconnect from electrical supply before servicing this
heater.
!
For longest product life & to maintain product appearance
mount heater under cover & protect from rain & weather
whenever possible.
The exterior housing of the heater should be cleaned
regularly. To clean the appliance, ensure heater is off and
has been off for at least 2 hours after operation, and wipe
off any dirt/dust with a soft damp cloth.
For locations near the coast, salt in the air can cause rusting
of metal. Additional cleaning of the heater with a soft
damp cloth fortnightly will increase the life of the products
appearance.
MAINTENANCE
SERVICING
WARNING
Servicing and maitenance MUST be carried out by an
authorised and licenced service person only.
!
WARNING
If the supply cord is damaged, it must be replaced by
Bromic, a service agent of Bromic or similarly qualified
persons in order to avoid a hazard. Contact Bromic for
further information on replacement of the supply cord.
!

15
www.bromicheating.com
REPLACEMENT PART LIST
No. Description Bromic Part No.
1 Platinum Electric 1500W BH0320001
2 Ceiling Recess Kit BH3130001
3 Umbrella Mounting Kit BH3130002
4 Tube Suspension Kit BH3130003
5 Chain Suspension Kit BH3130004
SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION
No heat 1. Improper connection 1. Check connection to power supply
Not enough heat 1. Heater too small for application
2. Heater mounted too high or too far
1. Add additional heater(s)
2. Decrease mounting height or distance
Too much heat 1. Heater too large for application
2. Heater mount too low or too close
1. Replace with smaller heater
2. Increase mounting height or distance
TROUBLESHOOTING

Version 1,1 EU
APPAREIL DE CHAUFFAGE ÉLECTRIQUE
PLATINUM SMARTHEAT™
PAR BROMIC
MANUEL D'INSTALLATION,
D'INSTRUCTION ET D'ENTRETIEN
DISPONIBLE EN VERSION 1500W
IMPORTANT
LISEZ CE MANUEL ATTENTIVEMENT
VOIR CONTREPLAT POUR DES INFORMATIONS IMPORTANTES
CONCERNANT CE MANUEL. CONSERVEZ CE MANUEL PRÈS
DE L'APPAREIL POUR FUTURE CONSULTATION.
!

18 www.bromicheating.com
!
IMPORTANT
Ce manuel contient d'importantes informations sur l'installation, l'utilisation et l'entretien des appareils de
chauage électriques Platinum Smart-Heat™. Veuillez accorder une attention particulière aux informations
importantes sur la sécurité présentées tout au long de ce manuel. Chaque information de sécurité sera
accompagnée de l'un des symboles de sécurité suivants:
DANGER AVERTISSEMENT IMPORTANT
•LISEZ ATTENTIVEMENT CE MANUEL avant l'installation ou
la réparation de ce produit.
•Une installation, une utilisation ou un entretien inappropriés
peuvent entraîner des dommages matériels, des blessures
corporelles graves ou la mort.
•Cet appareil est destiné à une installation xe avec 220-240 V CA de
puissance d'alimentation monophasée.
•L'installation DOIT être réalisée par un technicien qualié et agréé
en conformité avec les codes d'installation électrique locaux.
!
!
!
Siège: 10 Phiney Place Ingleburn NSW 3565 Australia
Téléphone: 1300 276 642 (En Australie) ou [phone] (de l'étranger) Fax: [phone]
E-mail: [email protected] Web: www.bromicheating.com
Remarque: Bromic Pty Ltd se réserve le droit d'apporter des modifications sur les descriptions, les pièces, les composants et les équipements sans avis préalable.
Ce manuel d'installation, d'utilisation et d'entretien ne doit pas être reproduit sous quelque forme que ce soit sans avis préalable écrit de Bromic Pty
Ltd.
Élimination correcte de ce produit
Ce marquage indique que ce produit ne doit pas être
éliminé avec d'autres déchets ménagers dans tout le
territoire européen. Pour éviter tout éventuel préjudice
à l'environnement ou à la santé humaine causé par
l'élimination incontrôlée des déchets, recyclez-les de façon
responsable afin de promouvoir la réutilisation durable
des ressources matérielles. Pour renvoyer votre dispositif
utilisé, veuillez utiliser les systèmes de renvoi et de collecte
ou contactez le détaillant où le produit a été acheté. Ceux-
ci peuvent procéder au recyclage du produit en toute
sécurité.

19
www.bromicheating.com
TABLE DES MATIÈRES
REMARQUES ET AVERTISSEMENTS IMPORTANTS 4
PRÉSENTATION DU PRODUIT 5
DESCRIPTION DU PRODUIT 5
SPÉCIFICATIONS 5
CARACTÉRISQUES DU PRODUIT 5
INSTRUCTIONS D'INSTALLATION DE L'APPAREIL DE CHAUFFAGE 6
MONTAGE SUR LE PLAFOND ET SUR LE MUR 6
PLAFOND ENCASTRÉ 8
MONTAGE PARAPLUIE 9
SUSPENSION AU TUBE 10
SUSPENSION À LA CHAÎNE 11
INSTALLATION ÉLECTRIQUE 12
RÉPARATION 12
LISTE DES PIÈCES DE RECHANGE 13
DÉPANNAGE 13

20 www.bromicheating.com
REMARQUES ET AVERTISSEMENTS IMPORTANTS
AVERTISSEMENT
•IMPORTANT - L'installation DOIT être réalisée par une personne
qualiée et agréée.
•Une installation, un réglage ou une altération inadéquat et le
non-respect des avertissements et des instructions contenus
dans ce manuel pourraient entraîner des blessures graves, la
mort des personnes ou être à l'origine des dégâts matériels.
•Le fabricant n'est pas responsable de quelque dommage qui
pourrait survenir à cause d'un mauvaise utilisation. Il souligne
que cet appareil doit être utilisé de manière responsable et
que tous avertissements, procédures et consignes de sécurité
contenus dans ce manuel doivent être strictement respectés.
•Le technicien chargé de l'installation doit s'assurer que les
exigences des autorités locales, les codes d'installation électrique
en vigueur, les codes municipaux du bâtiment ainsi que tous
autres règlements statutaires sont respectés.
•Ne posez pas d'objets sur ou contre cet appareil.
•N'utilisez et ne conservez pas de matériaux inammables près
de cet appareil.
•Ce manuel d'installation, d'utilisation et d'entretien ne doit pas
être emporté du lieu d'installation. Le technicien qui procède à
l'installation doit laisser le manuel au client pour que référence y
soit faite en tant que de besoin.
•Une distance de sécurité minimale de 1 000 mm doit toujours
être laissée au devant de l'appareil.
•Cet appareil doit être monté à un minimum de 1 800 mm au-
dessus du plancher.
•L'appareil ne doit pas être situé directement au-dessous ou en
face d'une prise de courant murale parce que la chaleur rayonnée
par l'appareil peut endommager la sortie d'électricité ou la che.
•Tout dispositif de protection enlevé pour réparer l'appareil de
chauage (par un personnel qualié) doit être replacé avant
l'utilisation de l'appareil de chauage.
•Cet appareil n'est pas destiné à être utilisé par des personnes (y
compris les enfants) atteints de décience physique, sensorielle
ou mentale, ou manquant d'expérience et de connaissances, à
moins qu'ils n'aient été formés et encadrés ou renseignés sur
l'utilisation de l'appareil par une personne responsable de leur
sécurité.
•Les appareils de chauage ne doivent pas être installés dans les
armoires.
•Les enfants doivent être supervisés quand ils se retrouvent à un
endroit où il y a un appareil de chauage.
•Les enfants et les adultes doivent être avertis des risques liés à
la forte température en surface et doivent se tenir à l'écart pour
éviter d'être brûlés, blessés ou que leurs vêtements prennent feu.
• Disposez les matériels d'emballage hors de portée des enfants.
•N'appliquez pas d'aérosols ou de produits inammables dans les
environs de cet appareil quand il fonctionne.
•L'installation et la réparation ne doivent être réalisées que par
un personnel d'entretien qualié. L'appareil de chauage doit
être inspecté avant utilisation et au moins une fois par an par un
personnel d'entretien qualié.
•Ne procédez pas à la réparation avant que l'appareil de chauage
ne soit arrêté, débranché et qu'il n'ait repris la température
ambiante.
• Certains matériaux ou objets conservés ou posés sous ou près
de l'appareil, sont soumis à la chaleur rayonnante et pourraient
être sérieusement endommagés. Les matières combustibles tels
que les murs, les planchers, les meubles, les luminaires et plantes
doivent être maintenus à au moins 1 100 mm sur les côtés et d'en
haut.
• N'accrochez et ne posez pas les vêtements ou les produits
inammables au dessus ou près de l'appareil de chauage.
•Assurez-vous que l'appareil de chauage n'est pas tourné vers
le plafond ou qu'il ne fait pas face aux substances / matériaux
inammables ou combustibles.
•Cet appareil de chauage par rayonnement n'est PAS destiné à
être installé sur véhicules et/ou bateaux récréatifs.
•N'essayez pas d'adapter l'appareil de quelque manière que ce
soit.
•Retirez la protection de transport avant l'utilisation.
•N'utilisez jamais l'appareil de chauage dans un environnement
prône aux explosions tel que des endroits dans lesquels l'essence
et les autres liquides inammables et produits vaporisant sont
stockés.
•Ne faites jamais une peinture sur quelque partie de l'appareil de
chauage que ce soit.
• Vériez les dommages sur l'appareil régulièrement. L'appareil de
chauage ne doit pas être utilisé si le panneau rayonnant noir ou tout
autre partie de l'appareil est endommagé. Si un endommagement
est suspecté sur l'appareil même, arrêtez immédiatement de l'utiliser
et contactez le fournisseur ou un personnel de réparation qualié.
•Après le déballage, assurez-vous que l'appareil ne présente
aucun signe d'endommagement visible ou tentative d'altération.
Si l'appareil semble endommagé, contactez le lieu d'achat pour
assistance.
• Cet appareil doit être utilisé uniquement sur un simple
approvisionnement en électricité monophasé 220-240 V CA.
•Ne touchez pas la surface chaude quelque soit le moment, même
lorsque l'appareil de chauage est éteint et refroidi.
•Ne touchez pas l'appareil de chauage avec les mains mouillées
quelque soit le moment.
•Si l'appareil n'a pas été utilisé, ou ne sera pas utilisé, pour un
longue période, débranchez l'alimentation électrique.
•À la n de la durée de vie utile de ce produit, il ne doit pas être
éliminé comme tout autre déchet domestique. En eet, il doit être
déposé dans un centre de collecte des déchets d'équipements
électriques et électroniques. Il est de la responsabilité de
l'utilisateur de se débarrasser de cet appareil par les voies
appropriées à la n de sa vie utile. Ne pas respecter cette consigne
peut vous soumettre à des sanctions établies par les lois régissant
l'élimination des déchets. La collecte particulière et appropriée,
et le recyclage, le traitement ainsi que l'élimination des déchets
par des voies compatibles à la protection de l'environnement
permettent d'éviter des dommages inutiles à l'environnement
et les risques éventuels liés à la santé, et permettent également
le recyclage des matières utilisées dans l'appareil. Pour de plus
amples informations sur la collecte et l'élimination des déchets,
contactez votre service local d'élimination des déchets, ou le lieu
d'achat.
• En cas de connexion directe à une conduite de fourniture, un
disjoncteur bipolaire à distance d'ouverture de contact d'au
moins 3 mm doit être xé en amont à partir de la conduite de
fourniture. Communiquez avec un technicien d'entretien agréé
!