BROOKING INDUSTRIES HORIZON User manual

WIRING
SINGLE / DUAL COLOR
to +VDC with rated fuse
(for correct fuse, refer to Fuse Rating chart)
to Chassis ground
BLACK
RED
NOTE:
[Px]
= Precedence order, when more than 1wire is activated at the same
time, higher precedence wire will affect lower precedence wire. P1 being
the highest priority.
BROWN
[+]
Warning Mode 1 [P4]
[+]
Warning Mode 2 [P3]
GREEN
[+]
End-Flasher (See “FIRMWARE SELECTION” for End-Flasher Mode)
[+]
Flash Pattern Selection /
[+]
Low Power Operation
YELLOW
[ ]
Control Panel Indicator Signal out /
[+]
Programming
[+]
Rear “Right Arrow” [P2]
ORANGE
BLUE
[+]
Rear “Left Arrow” [P2] Rear “Center Out Arrow” [P1]
POWER WIRES
1. Route Power Wires to the vehicle firewall towards the battery and follow the
factory wiring harness through the firewall. If drilling a hole is required, ensure
that no component is damaged from the drilling.
2. Install a fuse (user-supplied) to the end of the RED wire, and connect it to the
battery. (for correct fuse, refer to Fuse Rating chart)
3. Connect the BLACK wire to the factory chassis ground next to the battery.
NOTE: Ensure that all wires of the power cable are securely connected to the power
source.
TRAFFIC ARROW
1. Activate Traffic Arrow function by applying +VDC to:
■ORANGE wire for Left Arrow.
■BLUE wire for Right Arrow.
■Above 2 wires together for Center-Out.
NOTE: If the stick is equipped with Dual Color lightheads,Traffic Arrow will display
in Color 2.
2. To change the Traffic Arrow flash pattern, tap
+VDC to YELLOW wire:
a. quickly 1 time to next pattern. (refer to Traffic Arrow Patterns chart).
CONTROL WIRES
1. Route Control Wires towards the dash area to a switch panel (user-supplied).
2. Connect the required wires to a controller (switch panel) or power source.
CONTROL PANEL SIGNAL INDICATOR
Connect WHITE wire to the display signal input of a compatible Control Panel to
display current lighthead activity.
b. quickly 3 times to revert back to Traffic Arrow Pattern #1.
WARNING MODE 1 and MODE 2
Each Warning Mode is capable of storing / saving one flash pattern.
To change the flash pattern:
1. Activate a warning Mode by applying +VDC to
BROWN , or GREEN wire.
■BROWN wire for Warning Mode 1.
■GREEN wire for Warning Mode 2.
2. Once a warning mode is activated, tap +VDC to YELLOW wire:
a. quick 1 time to next pattern (refer to Flash Pattern chart).
b. quickly 3 times to revert back to Pattern #1.
To set color mode (for Dual Color Models only):
1. Disconnect all power,then apply +VDC to BROWN (or GREEN), and
RED wire together for 3 seconds to enter color setting mode; the stick will
display the current color mode for the activated warning mode.
2. Tap +VDC to wire to scroll through the color modes:
a. Single Color 1 b. Single Color 2 c. Dual Color 1&2 d. Dual Color 2&1
3. Save and exit color setting by disconnecting all power.
LOW POWER OPERATION (DIM FUNCTION)
Activate dimming function by continuously applying +VDC to YELLOW wire.
End Flasher Patterns
1 Double (All) [R65]#
2 Quad (All)[2HZ]
3 Single (All)[2HZ]
4 Double (All)[SAE]
5 Quad (All)[SAE]
6 Single (All)[SAE]
7 Double (Left Right)[2HZ]
8 Quad (Left Right)[2HZ]
9 Single (Left Right)[2HZ]
10 Double (Left Right)[SAE]
11 Quad (Left Right)[SAE]
12 Single (Left Right)[SAE]
Single color model: Patterns 1~11 are available
Dual color model: C1 = Color 1; C2 = Color 2; C1&2 = Color 1&2
1 Random/Custom (see “PROGRAMMING”)
2 All Double [R65]#
3 All Single [2HZ]
4 All Triple [2HZ]
5 All Quad [2HZ]
6 All Steady / Scene
7 All Single [SAE, CA13]
8 All Double [SAE]
9 All Mega
10 All Ultra [SAE]
11 All Single-Quad
12 All Single H/L
13 All Single-Triple-Quint
14 Left-Right Single
15 Left-Right Double
16 Left-Right Mega
17 Left-Right Ultra
18 Side-by-Side Single
19 Side-by-Side Double
20 Side-by-Side Mega
21 Side-by-Side Ultra
22 Outside-in Single
23 Outside-in Double
24 Outside-in Mega
25 Outside-in Ultra
26 All Scan
27 Split Scan
28 Left-Right Single Mid
29 Left-Right Double-Single
30 Left-Right Triple-Single
31 Left-Right Quad-Single
32 Left-Right Single H/L II
33 Left-Right Double-Blast
34 Left-Right Swing I
35 Left-Right Triple-Blast
36 Left-Right Swing II
37 Left-Right Swing III
38 Left-Right Triple H/L
39 Side-by-Side Single Fast
40 Side-by-Side Quad Fast
41 Side-by-Side Double Fast
42 Side-by-Side Quad-Double
43 CompositeQuad-Scan-Blast
44 Side-by-Side Mega X *
45 Composite All Scan-Split Scan
46 Composite Triple-Scan
47 Composite Single-Scan-Blast
48 Composite Solid Scan *
49 Composite Solid Scan-Mega *
50 Composite Solid Scan-Blast *
Warning Patterns
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
Traffic Arrow Patterns
1 Sweep Single
2 Sweep Double
3Sweep Triple
4Sweep 1 End x2
5Solid
6Solid End x2
7Solid Chaser
8Solid Fade
9Blink Double
10 Blink Triple
11 Blink Solid
25 Solid Chaser Dual Quick
26 Solid Chaser D
27 Solid Chaser Dual Slow
23 Sweep Single w/ Dual End Flasher [2HZ]
24 Sweep Single w/ Dual End Flasher [SAE]
For dual color models:
SC = Single Color Mode; SC/DC = Single or Dual Color Mode
# Actual ECE R65 approval is based on the p/n ordered.
* Patterns show full effect in dual color mode.
12 Sweep Single
13 Sweep Double
14 Sweep Triple
15 Sweep 1 End x2
16 Solid
17 Solid End x2
18 Solid Chaser
19 Solid Fade
20 Blink Double
21 Blink Triple
22 Blink Solid
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1&2
C1&2
C1&2
C1&2
C1&2
# Actual ECE R65 approval is based on the p/n ordered.
Fuse Rating
No. of
Lightheads
12VDC
Model
24VDC
Model
6-Head
8-Head
10-Head
5.0A
7.5A
10.0A
3.0A
4.0A
5.0A
-1-
HORIZON Traffic Advisor / Warning Stick Manual
or
HORIZON Traffic Advisor / Warning Stick Manual

FIRMWARE SELECTION - END-FLASHER MODE
All units are pre-set to the firmware of its number of lightheads.
To change firmware to Traffic Arrow with End-Flashers:
and YELLOW wires simultaneously for more than 3 seconds to enter FIRMWARE
2. Once in FIRMWARE selection mode, the unit will display one of the following patterns.
3. Momentarily apply YELLOW wire to
+VDC
to scroll through FIRMWARES.
4. Once desired FIRMWARE is selected, save and exit by disconnecting all power.
10-Head Traffic Arrow
steadysteadysteady
10-Head Traffic Arrow with End Flashers (Single Pair)
steadysteadysteady
10-Head Traffic Arrow with End Flashers (Dual Pair)
steadysteadysteady
8-Head Traffic Arrow
steadysteady
8-Head Traffic Arrow with End Flashers (Single Pair)
steadysteady
8-Head Traffic Arrow with End Flashers (Dual Pair)
steadysteady
1. A pply +VDC to RED,
selection mode.
6-Head Traffic Arrow
steady
6-Head Traffic Arrow with End Flashers (Single Pair)
steady
steady
6-Head Traffic Arrow with End Flashers (Dual Pair)
not available
Q-LOCK™ MECHANISM & LIGHTHEAD SWAP
Replace / reconfigure lightheads quickly and efficiently using the patent pending Q-Lock coupling mechanism.
1. Use a flathead screwdriver,flip open the Q-Lock™ levers on both sides of the lighthead(s) to be removed / replaced.
2. Remove the lighthead by pulling it out slowly and evenly from both sides.
a. Inserting the flathead screwdriver blade into the side of the Q-Lock once flipped open to remove the first lighthead. Once (1)
lighthead is removed, the remaining ones will loosen and dislodge without the use of the blade.
3. Carefully disconnect the lighthead wire from the wire harness, making sure to press the knob on the chassis side down and through
the bridge on the lighthead side. DO NOT ATTEMPT TO DISCONNECT BY PULLING THE WIRES.
4. Connect the new lighthead. Note the direction and the orientation of the lighthead to ensure it matches the neighboring lightheads.
(check wire-exit and lens marking)
5. Push the lighthead slowly and evenly into place.
6. Flip and close all Q-Lock™ levers.
-2-
CLOSE

OPEN



OPEN

