WIRING
SINGLE / DUAL COLOR
to +VDC with rated fuse
(for correct fuse, refer to Fuse Rating chart)
RED
to Chassis ground
BLACK
time, the higher precedence wire will affect lower precedence wire. P1
being the highest priority.
BROWN
[+]
Warning Mode 1
[P2]
[+]
Warning Mode 2
[P1]
GREEN
[+]
Flash Pattern Selection / Synchronization
Connect YELLOW wires of all sticks together for synchronization
(All sticks should be set to the same pattern)
YELLOW
[+]
Low Power Operation
NOTE:
[Px]
= Precedence order, when more than (1) wire is activated at the same
POWER WIRES
1. Route Power Wires to the vehicle firewall towards the battery and follow the
factory wiring harness through the firewall. If drilling a hole is required, ensure
that no component is damaged from the drilling.
2. Install a fuse (user-supplied) to the end of the RED wire, and connect it to the
battery. (for correct fuse, refer to Fuse Rating chart)
3. Connect the BLACK wire to the factory chassis ground next to the battery.
NOTE: Ensure that all wires of the power cable are securely connected to the power
source.
CONTROL WIRES
1. Route Control Wires towards the dash area to a switch panel (user-supplied).
2. Connect the required wires to the switch panel or power source.
WARNING MODE 1 and MODE 2
Each warning mode is capable of storing / saving one pattern.
To change the flash pattern:
1. Activate the desired Warning Mode by applying +VDC to
BROWN
, or
GREEN
wire.
■BROWN wire for Warning Mode 1.
■GREEN wire for Warning Mode 2
2. Let the warning mode run for at least 3 seconds then:
a. tap YELLOW wire to +VDC scroll through warning patterns.
b. tap YELLOW wire to +VDC quickly 3 to revert back to flash pattern #1.
COLOR MODE SETTING (available w/ dual color models only):
1. Disconnect all power,then apply +VDC to BROWN (or GREEN), YELLOW and
RED wire together for at least 3 seconds to enter color setting; the stick will display
the current color mode for the activated warning mode.
2.
Tap +VDC to YELLOW wire to scroll through the color mode:
a.
Color 1
b.
Color 2
c.
Color 1&2 Alternating flash
d.
Color 2&1 Alternating flash
3. Save and exit color setting mode by disconnecting all power.
LOW POWER / DIMMING MODE
Activate dimming function by continuously applying +VDC to WHITE wire.
1 Random
2 All
3 All
4 All
5 All
6 All
7 All
8 All
9 All
10 All
11 All
12 All
13 All
14 Left Right
15 Left Right
16 Left Right
17 Left Right
18 Side-by-Side
19 Side-by-Side
20 Side-by-Side
21 Side-by-Side
22 Outside-in
23 Outside-in
24 Outside-in
25 Outside-in
26 All
27 Split
28 Left Right
29 Left Right
30 Left Right
31 Left Right
32 Left Right
33 Left Right
34 Left Right
35 Left Right
36 Left Right
37 Left Right
38 Left Right
39 Side-by-Side
40 Side-by-Side
41 Side-by-Side
42 Side-by-Side
43 Composit
44 Side-by-Side
45 Composite
46 Composite
47 Composite
48 Composite
49 Composite
50 Composite
Double [R65]#
Single [2HZ]
Triple [2HZ]
Quad [2HZ]
Steady / Scene
Single [SAE, CA13]
Double [SAE]
Mega
Ultra [SAE]
Single-Quad
Single H/L
Single-Triple-Quint
Single
Double
Mega
Ultra
Single
Double
Mega
Ultra
Single
Double
Mega
Ultra
Scan
Scan
Single Mid
Double-Single
Triple-Single
Quad-Single
Single H/L II
Double-Blast
Swing I
Triple-Blast
Swing II
Swing III
Triple H/L
Single Fast
Quad Fast
Double Fast
Quad-Double
Quad-Scan-Blast
Mega X *
All Scan-Split Scan
Triple-Scan
Single-Scan-Blast
Solid Scan *
Solid Scan-Mega *
Solid Scan-Blast *
Warning Patterns
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
# Actual ECE R65 approval is based on the p/n ordered.
* Patterns show full effect in dual color mode.
For dual color models:
SC = Single Color Mode; SC/DC = Single or Dual Color Mode
Fuse Rating
No. of
Lightheads
12VDC
Model
24VDC
Model
2-Head
4-Head
2.0A
4.0A
1.0A
2.0A
-1-
HORIZON Warning Stick Manual
