Brymen BM035 User manual

Eshop: www.emareg.cz Email: [email protected]
USER'SMANUAL
Mìøící a dílenské pøístroje / Kleové multimetry
uvádí:
BRYMEN BM037, BM035, BM033, BM031
BRIGHTPEOPLESCHOICE

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
1
Themeter meets UL/IEC/EN610101Ed. 3.0, CAN/CSAC22.2No.61010 1 Ed.3.0,
UL/IEC/EN610102032 Ed. 3.0, UL/IEC/EN610102033 Ed. 1.0 to Measurement
CATIII 600VandCATIV 300V,AC&DC.
The accompanied test probeassemblymeetsUL/IEC/EN61010 031 Ed.2.0to the
samemeterratingsorbetter. IEC61010031requiresexposedconductivetestprobe
tipstobe 4mmforCATIII&CATIVratings.Refertothecategorymarkingsonyour
probeassembliesaswellasontheadd onaccessories(likedetachableCapsor
AlligatorClips),ifany,forapplicableratingchanges.
identifiesconditionsandactionsthatcouldresultinseriousinjuryoreven
deathtotheuser.
identifiesconditionsandactionsthatcouldcausedamageormalfunction
intheinstrument.
Thismanualcontainsinformationandwarningsthatmustbefollo wedforoperatingthe
meter safelyandmaintainingthe meter inasafeoperatingcondition.Ifthe meter is
usedinamannernotspecifiedbythemanufacturer,theprotectionprovidedbythe
meter maybeimpaired.
Observepropersafetyprecautionswhenwo rkingwithvoltagesabove3 0 Vrms,42.4
Vpeakor 60VDC.Thesevoltagelevelsposeapotentialshockhazardtotheuser. Do
notexposethisproducttorainormoisture.Themeterisintendedonlyforindooruse.
Keepyourhands/fingersbehindthehand/fin gerbarriers(ofthemeterandthetest
probeassembly,whereapplicable)thatindicatethelimitsofsafeaccessofthehand 
held parts during measurements. Inspect lead wires, connectors, and probes for
damagedinsulationorexposedmetalperiodically.I fanydefectsarefound,replace
themimmediately. Optionaloffer premiumsilicon test leadwires
equipwith whiteinner insulation layeraswearindicator. Donot usethem ifthewear
indicatorhasbecomevisible . Onlyusetheprob eassemblyprovidedwiththemeteror
aULListedProbeAssemblytothesamemeterratingsorbetter.

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
2
Marking ofElectricalandElectronicEquipment (EEE). Donotdisposeofthis
productasunsortedmunicipalwaste. Contactaqualifiedrecycler
Caution!RefertotheexplanationinthisManual
Caution! Possibility ofelectricshock
Earth(Ground)
Meterprotectedthroughout by DoubleInsulationorReinforcedinsulation
Fuse
Direct Current(DC)
AlternatingCurrent (AC)
Threephase Alternating Current
Applicationaroundandremovalfromhazardousliveconductorsispermitted
isapplicable totestandmeasuringcircuitsconnectedat
voltage MAINS installation. Examples are
measurementsondevicesinstalledbeforethemainfuseorcircuitbreakerinthe
buildinginstallation.
isapplicabletotestandmeasuringcircuitsconnectedto
voltageMAINSinstallation.Examplesare
measurementsondistributionboards(includingsecondarymeters),circuit breakers,
cables, busbars,junctionboxes,swi tches, socketoutlets,stationarymotors in the
fixedinstallation,andequipmentforindustrialuse.
isapplicabletotestandmeasuringcircuitsconnected
directlytoutilizationpoints(socketoutletsandsimilarpoints)ofthel owvoltage MAINS
installation. Examples are measurements on MAINS CIRCUITS of household
appliances,portabletoolsandsimilarequipment.
The instruments conform to CENELEC Lowvoltage directive 2014/35/EU,
Electromagneticcompatibility directive2014/30/EU andRoHSdirective 2015/863/EU.
Thisuser'smanualusesonlyrepresentativemodel(s)forillustrations.Pleaserefer
specificationdetailsforfunctionavailabilitytoeachmodel.

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
3
1) Antenna area for NonContactEF
Detection
2) Jaw center indicator (with DCA
polarityforModels037&035), atwhere
best current accuracyisspecified
3) Pushbuttonsforspecialfunctions&
features.
4) Rotary Selector to turn the power
ON/OFF andselectafunction
5) 35/6 digits 6000 counts numeric
LCD display
6) InputJackforallfunctionsEXCEPT
noninvasive Currentfunctions
7) Common (Ground reference) Input
Jack for all functions EXCEPT the
Clampon Current andNonContactEF
Detection functions
8) Jawtriggerforopeningtheclampjaw
9) Hand/FingerBarriertoindicatethe
limitsofsafeaccessofthemeter
10) Clamp Jaw for Clampon Current
magnetic fieldpickup
11) Additional center indicator for AmpTipTM Lowcurrent functions,atwherebest
AmpTipTM currentaccuracyisspecified
Beforeandafterhazardousvoltagemeasurements,testthevoltagefunctionona
knownsourcesuchaslinevoltagetodeterminepropermeterfunctioning

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
4
Inputs are madethroughthetestlead terminals . Defaults at Function.
Press button momentarilyto select function.
Note:
and functionsareequippedwithlow passfilter,andarecapableof
dealing with (VariableFrequencyDrives)signals. Italsoimprovesreadingstability
innoisyelectricalenvironments.
Inputsaremadethroughthetestlead terminals .
Pressthejawtriggerandclampthejawsaroundconductor(s)ofonlyonesinglepoleof
acircuitforloadcurrentmeasurement s.Makesurethejawsarecompletelyclosed,or
elseitwillintroducemeasurementerrors.Enclosi ng conductor(s) of more than one
pole ofacircuit may resultindifferentialcurrent(likeidentifyingleakagecurrent)
measurements. Align the conductor(s) to the Jaws center indicators (Regular or

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
5
AmpTip indicatorswhereapplicable)as muchaspossibletogetthebestmeasuring
accuracy. For removal, press the jaw trigger and remove the jaws from the
conductor(s).
Adjacentcurrent carryingdevicessuchastransformers,motorsandconductorwires
may affect measurement accuracy. Keep the jaws away from them as much as
possibletominimizeinfluence.
This Clamponmeterseriesisdesignedtodirectlyapplyaroundorremovefrom
uninsulatedhazardousliveconductors.Butstill,individualprotectiveequipmentmust
beusedifhazardouslivepartsintheinstallationwheremeasurementistobecarried
outcouldbeaccessible. Donotusethemetertomeasurecurrentsabovetherated
frequency(400Hz).C irculatingcurrents may cause themagneticcircuitsoftheJaws
reachahazardoustemperature.
Input is made via theclampjaws wherebestaccuracyisspecifiednearthe jaw TIP
CENTER area for lowcurrentmeasurementsofthin conductors. Defaults at .
Press buttonmomentarilyto select forModels035&037.

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
6
Input is made via theclampjaws wherebestaccuracyisspecifiedatthe jaw CENTER
area. Defaultsat . Press buttonmomentarilyto select forModels
035&037.
Inputsaremadethroughthetestlead terminals . Defaults at .
Press buttonmomentarilyto select thesubject functions insequence. For
Models035&031, function islocated inanindependentrotary
switchposition
This function is having improved convenience forcheckingwiringconnectionsand
operationofswitches. Resistancethresholdisbeingused. A continuous beep tone
togetherwithflashing display backlight indicateacompletewire. Such audible and
visibleindicationsimprovecontinuityreadabilities innoisyworkingenvironments.
Forwardvoltagedrop(forwardbiased)foragoodsilicondiode
isbetween0.400Vto0.900V.Ahigherreadingindicatesaleakydiode(defective).A

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
7
zeroreadingindicatesashorteddio de(defective).Anover rangedisplayindicatesan
opendiode(defective).Reversethetestleadsconnections(reversebiased)acrossthe
diode.Thedigitaldisplayshowsover rangeifthediodeisgood.Anyotherreadings
indicatethediodeisresistiveorshorted(defective).
Whenthedisplayreadingdropsacross0.850V,
themeteralertsashortbeeptosignalareasonableforwardvoltagedropofcommon
diodes. However, if the reading further drops below 0.100V, the meter gives a
continuous beeptonetogetherwithflashingdisplaybacklighttoindicateashorted
diodeoracompletewire.Itissimilartothatof function but
,instead,isbasedonvoltagethresholdtoindicateacompletewire.
Using , or functioninalivecircuit
willproducefalseresultsandmaydamagethe meter.Inmanycases , thesuspected
component(s) must be disconnected from the circuit to obtain an accurate
measurementreading.

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
8
Defaults at highsensitivity . T Ifitistoo
sensitiveforyourapplications,press button momentarily to select lower
sensitivity .ThedetectedElectricField strengthisindicatedasaseriesofbar 
graphsegmentsonthedisplayplusvariablebeeptones.
Anantennaislocatedalongthetop rightend of
the stationaryclampjaw ,whichdetectselectricfieldsurrounds energized conductors.
Itisidealfortracinglivewiringconnections,locatingwiringbreakageandtodistin guish
betweenliveorearthconnections.
Formorepreciseindicationoflivewires,suchas
distinguishingbetween Liveand Groundconnections,use onesingle probe to test via
terminal for direct metal ProbeContact EFDetection to achieve the most
distinctiveindication.

Eshop: www.emareg.cz Email: [email protected]
www.eMAReg.cz
9