Bullerjan B4 Keramik User manual

Installation Manual
Bullerjan B4Keramik and Keramik+
Please read these instructions carefully before starting the
installation!
We strongly recommend that the assembly be carried out in pairs and by
qualified personnel.
In addition, the following must be observed during assembly:
• Rubberized working gloves should be worn
• Always tighten all screws of the ceramics only hand-tight
• Always lay and place the ceramic on a soft surface
• The stove must be aligned horizontally before installing the ceramic

Seite | 2
IMPORTANT:
If you want to use the flue gas nozzle at the back of the stove, the flue gas nozzle
must be converted before the ceramic cladding is installed and the stove pipe
must be connected. In addition, the backside of the stove has to be hung over
the stove pipe at this time in order to be able to mount it later on to the stove.
For assembly you need the following tools:13er Maulschlüssel
10er oben-end wrench
2,5er allen wrench
3er allen wrench
4er allen wrench
Medium-sized slotted screwdriver
Water spirit level
Screws (included - please check for completeness):
8 x threaded pin (M5 x 12)
8 x threaded pin (M5 x 20)
2 x hexagon socket round head screw (M5 x 10)
Screws (included with the respective component - please check also for
completeness):
Ceramic tea-shelf
o2 x Holders for tea-shelf (equal parts)
or
Set of holders for ceramic front cover
o2 x Holder for front cover (1x richt / 1x left)
and/or
Set of holders for ceramic cover plate
o2 x threaded pin (M8 x 50)
o2 x nut (M8)
o2 x nut (M8 with collar)
o2 x washer (M8)

Seite | 3
1. Place the stove at its future
location before installing the
ceramic parts.
Align the stove with a water
spirit level.
2. Use the height adjusters in the
base of the stove for alignment.
These can be adjusted with a
4er allen wrench a 13 mm open
end wrench.
3. Now screw two of the shorter
threaded pins (M5 x 12) into the
lower ceramic holder so that they
are flush with the bottom.
4. Please turn four of the longer
threaded pins (M5 x 20) in the two
middle ceramic holders, so that they
are halfway above and the other half
below the holder.

Seite | 4
5. Now screw two of the shorter
threaded pins (M5 x 12) into
the upper ceramic holder so
that they are flush with the
upper side.
6. Loosen the screw connection of the
second holder and put it aside.
Slightly loosen the two mounting
screws of the lower holder (below
the stove).
7. Now place the bottom side
ceramic tilke on the threaded
pins. Attention: When fitting
ceramic + - the rounded side of
the ceramic must point
downwards.
8. Insert the setscrew ends of the
second holder into the ceramic
and position the ceramic. Make
sure that there is no gap
between the metal stove corpus
and the ceramic.

Seite | 5
9. Now attach the ceramic holder
hand-tight to the stove for the
time being.
10. Align the ceramic in such a way
that a gap of approx. 3-5 mm is
created for the wood box. Now
tighten both the screws of the
lower and the upper ceramic
holder.
11. Repeat steps 7-10 when
attaching the center ceramic
element.
12. The installation of the upper
ceramic element follows also the
steps 7-10.

Seite | 6
13. Repeat steps 7-12 for the
opposite side.
14. Now place the tea-shelf or
front cover on the stove so
that the position pins on the
stove are fully inserted into
the component.
15. Use the holders to fix the front
cover. Positioning of the holders
see picture. Repeat this step on
the other side of the front cover.
16. This is what you see when both
holders are installed.

Seite | 7
17. This is what you see when you
have chosen a tea-shelf.
18. Before mounting the ceramic
cover plate, two threaded
pins (M8 x 50) must be
screwed in. Furthermore,
please turn one nut each
(M8) on the pins.
21. Now place the ceramic cover
plate on the stove.

Seite | 8
20. Attach the cover plate to the back
of the stove as shown in the
picture. The mounting of the cover
plate made of steel is identical. The
two threaded pins, which also serve
to secure the front cover, allow to
aligne to aligne the cover plate if
necessary.
For further information, please contact:
Bullerjan GmbH
Neuwarmbüchener Str. 2
30916 Isernhagen
Tel.: [phone]
Email: [email protected]
Modifications and errors reserved / Version: 09/2018
22. The last step is to fix the rear wall
of the stove.