Bullet tools EZ Shear 220 User manual

Quick Start Guide
for EZ Shear Model #220
for EZ Shear Model #226
A. (4) M6 x 65mm PH Phillips Machine Screws
B. (4) M6 Star Washers
C. (6) M6 x 25mm PH Phillips Machine Screws
1. Power Assembly
1a. Safety Lock pin
2. Handle Assembly
3. Fence
4. Table The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.
5. Tail
6. Rails x 2
7. Hone Stone
8. Mounting Brackets x 4
9. Hardware Kit
D. (5) M6 x 16mm FH Phillips Machine Screws
E. (4) #10 x 1 FH Phillips Self Tapping Screws
F. (2) M8 x 50mm Hex Bolts
G. (2) M6 Wing Nuts
In the Box: In the Hardware Kit:
A. (8) M6 x 65mm PH Phillips Machine Screws
B. (8) M6 Star Washers
C. (8) M6 x 25mm PH Phillips Machine Screws
1. Power Assembly
1a. Safety Lock pin
2. Handle Assembly
3. Fence
4. Table The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.
5. Tail
6. Rails x 4
7. Hone Stone
8. Mounting Brackets x 4
9. Hardware Kit
D. (6) M6 x 16mm FH Phillips Machine Screws
E. (4) #10 x 1 FH Phillips Self Tapping Screws
F. (2) M8 x 50mm Hex Bolts
G. (1) M6 Allen Wrench
In the Box: In the Hardware Kit:
Tools needed: #2 & #3 Phillips head screwdrivers and a 1/2” (13mm) socket or wrench.
IMPORTANT! Start all screws BY HAND when assembling your shear. This will help avoid cross-threading.
ASSEMBLING YOUR SHEAR
1. AT TACH R AILS
Attach rails and mounting brackets to Power
Assembly base using Item A machine screws, fitted
with Item B star washers.
2. AT TACH TAI L
Attach tail and mounting brackets to rails using
Item C machine screws. Make sure holes in tail are
facing up.
1
3. AT TACH TAB LE
A. Attach table to base starting
with front, start screws by
hand, use Item D screws.
B. Attach back of table to tail
using Item E self tapping screws.
Tighten with #2 Phillips.
3
3B
3A
Tail
2

4. ATTACH HANDLE:
For 220:
Insert Item F screws and tighten with 1/2”
wrench.
For 226:
Insert Item F screws through back stroke
stop and tighten with Item G hex wrench.
220 226
5. PLACE THE FENCE
For 220:
Your EZ Shear is equipped with an aluminum fence which may be
set to common roof pitches. (4/12, 6/12, 8/12, and 12/12) Simply
align with desired position and press pins into place.
Note: The fence is friction fit (requires effort to insert or remove).
For 226:
Slide fixed clamp into the front quick alignment notch.
For 90° cuts, slide loose clamp into rear alignment notch
and tighten star knob.
For angle cuts:
1) Align edge of fence with the desired angle guide mark
in center of table.
2) Slide loose clamp to edge of table and tighten knob.
220
226
5
4
SST CUT GUIDE
Max Thickness = 1” or 25mm
Material List
Siding, Fiber Cement Board
Siding, Pressboard Lap
Siding, Vinyl
Siding, Wood
Trim, OSB
Trim, Fiber Cement
Trim, Vinyl
Shingles, Tar or Wood
For full manuals, warranty info,
accessories, & tips on using and
maintaining your EZ Shear, go to
BulletTools.com or scan
the QR code below.
PRT-INS-QEZB REV.A.6.15 ©2015 Bullet Tools
MAKING CUTS
While gently pushing
handle down, pull Safety
Lock Pin out, lift handle.
12
3
Place product on table.
Bring handle down until
blade touches material.
Push handle down until
material is completely cut.
Hayden, ID USA • 208-772-0175