BURLI MAMMOTH User manual

MAMMOTH SQUAT STAND
Installation Manual

2
MAMMOTH SQUAT STAND
Disclaimer
This equipment must be used with care by capable and competent individuals under supervision, if
necessary. The use of any fitness equipment, including this one, involves the potential risk of injury. You
accept and assume full responsibility for any and all injuries, damages (both economic and non-
economic), and losses of any type, which may occur, and you fully and forever release and discharge
BURLI, LLC, its insurers, employees, officers, directors, associates, and agents from any and all claims,
demands, damages, rights of action, or causes of action, present or future, whether the same be known
or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
BURLI, LLC MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE
OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN USE OF THE EQUIPMENT.

3
MAMMOTH SQUAT STAND
Important Safety Notes
There is a risk assumed by individuals who use this type of equipment. Before beginning this or any
other exercise program consult your physician. This is especially important for individuals over the age of
35 or persons with pre-existing health problems. BURLI, LLC assumes no responsibility for personal injury
or property damage sustained by or through use of this product.
1. This product must be assembled on a flat, level surface to assure its proper
function.
2. Inspect and tighten all parts before every use. Replace any worn parts
immediately. Failure to do so may result in serious injury.
3. Keep children away from the Mammoth Squat Stand at all times.
4. Keep your hands and fingers away from moving or hinging parts.
5. Exercise with care to avoid injury.
6. If unsure about the proper use of the Mammoth Squat Stand contact
BURLI, LLC at 503-406-8882.

4
MAMMOTH SQUAT STAND
Parts Included
Key
Description
Quantity
A
Upright Post
x2
B
Base
x2
C
Crossmember Support
x1
D
Support Brackets
x4
E
Fat/Skinny Combo Pull-up Bar or
Single Pull-up Bar
x1
F
Mammoth J-Cups
x2
Hex Bolts (5/8” x 5”)
x16
Nyloc Nuts (5/8”)
x16
Washers (5/8”)
x32
A
B
C
D
E
F

5
MAMMOTH SQUAT STAND
Step 1 – Assemble Base
Tools Required: Level, Stepladder, Adjustable Wrench, 15/16th Socket Wrench
Materials Included: Base (2), Crossmember Support (1), Hex Bolt (4), Nyloc Nut (4), Washer (8)
Materials Needed:None
1. Arrange Base components approximately 4’ apart and parallel to each other
2. Place Crossmember Support between Base components as illustrated
2.1. Note: Both ends of the Base components are identical
3. Fasten Crossmember Support to Base components
3.1. Slide Washer onto Hex Bolt
3.2. Thread Hex Bolt and Washer through Base component and Crossmember
support toward the middle of the Squat Stand
3.3. Slide second Washer onto Hex Bolt
3.4. Fasten Nyloc Nut onto Hex Bolt
3.5. Repeat 4x
4. Tighten all 4 Hex Bolts using Adjustable Wrench and 15/16th Socket Wrench

6
MAMMOTH SQUAT STAND
Step 2 – Attach Upright Posts
Tools Required: Level, Adjustable Wrench, 15/16th Socket Wrench
Materials Included: Upright Post (2), Support Bracket (4), Hex Bolt (8), Nyloc Nut (8), Washer (16)
Materials Needed:None
Attach Support Brackets
1. Place 1 Support Bracket on either side of left Base component
2. Attach Support Brackets using Hex Bolts
2.1. Align two lower holes of the Support Brackets with holes on left Base
component
2.2. Slide Washer over Hex Bolt
2.3. Insert Hex Bolt through outside Support Bracket, Base component and
inside Support Bracket
2.4. Slide second Washer over Hex Bolt
2.5. Fasten Nyloc Nut on Hex Bolt
2.5.1. Note: Leave Hex Bolts loosely fastened
2.6. Repeat steps 2.1 – 2.6 for Support Brackets on right Base component

7
MAMMOTH SQUAT STAND
Step 2 – Attach Upright Posts Continued
Attach Upright Posts
1. Place 1 Upright Post on left Base component between Support Brackets
1.1. Note: The side of the Upright Post with numbering should face toward the
front of the Squat Stand
2. Align holes in Upright Post to holes in Support Brackets
3. Attach Upright Post to Support Brackets using 2 Hex Bolts
3.1. Slide Washer over Hex Bolt
3.2. Insert Hex Bolt through outside Support Bracket, Base component and
inside Support Bracket
3.3. Slide second Washer over Hex Bolt
3.4. Fasten Nyloc Nut on Hex Bolt
3.4.1. Note: Leave Hex Bolts loosely fastened
4. Repeat step 3 for Upright Post on right Base component
5. Tighten all 4 Hex Bolts on both left and right Support Brackets using
Adjustable Wrench and 15/16th Socket Wrench
5.1. Note: Use a level while tightening bolts to ensure Upright Posts are plumb

8
MAMMOTH SQUAT STAND
Step 3 – Attach Pull-up Bar
Tools Required: Level, Adjustable Wrench, 15/16th Socket Wrench
Materials Included: Fat/Skinny Combo Pull-up Bar or Single 1.25” Pull-up Bar (1), Hex Bolt (4), Nyloc Nut
(4), Washer (8)
Materials Needed:None
Assembly instructions are the same for both the Fat/Skinny Pull-up Bar and Single
1.25” Pull-up Bar. When attaching the Fat/Skinny Pull-up Bar, the lower of the 2
bars is the one that will be in use. Assemble according to your preference.
1. Place Pull-up Bar at preferred height near the top of the Upright Posts
2. Attach Pull-up Bar to Upright Posts using 4 Hex Bolts
2.1. Slide Washer over Hex Bolt
2.2. Insert Hex Bolt through outside Upright Post and Pull-up Bar bracket
2.3. Slide second Washer over Hex Bolt
2.4. Fasten Nyloc Nut on Hex Bolt
2.4.1. Note: Leave Hex Bolts loosely fastened
3. Tighten all 4 Hex Bolts using an Adjustable Wrench and 15/16th Socket Wrench