Burnside T355 User manual

a
a
2
1 (a) Slide back the
hinged lid to unlock it,
then (b) swing it open.
3 Press down
upon the hinged
lid and slide it
across so that it
locks into
place.
Ring back test
The ring back test can confirm the link with the connected phone as well as the Caller ID
feature (if supported) and the current ring style. If possible you should also test by making
calls to, and receiving calls from another phone.
1 Lift the handset and dial *9#
2 Replace the handset. The attached phone should ring (for 30 seconds).
If the phone supports Caller ID, the display should show the number ‘01234567890’
and the message ‘Test Call’.
Making calls
1 Lift the handset and listen for a dial tone.
If you hear a series of short tones, the T355 terminal is either waiting for a PIN code
(see ‘Enter a PIN code’ overleaf) or no SIM card is installed.
2 Dial the required number and then press the #key to place the call.
If you do not dial #, the call will be placed automatically three seconds after the last
button is pressed. You can adjust the delay period (see ‘Dial delay’ within the full user
guide for details).
Receiving calls
• Whenthephonerings,liftthehandsetandtakethecallinthenormalway.
If the caller’s number is made available by the network, and the attached phone sup-
ports Caller ID, it will be shown on the display of the phone.
Setting up
Remove the cover
Place the terminal on a level sur-
face. Grip the ridges on either side
of the light-grey top cover and lift it
gently from the base unit. This will
reveal the SIM card holder and the
battery.
(a) Insert the SIM card
into the hinged lid
as shown.
(b) Swing
shut the
hinged lid
ensuring that the
SIM card remains
fully in place.
Install your SIM card
Note: Ensure the unit is switched off (see inside pages) before installing a SIM card.
AMBER
AMBER AMBER
GREEN
GREEN
(
)
POWER
STATUS GREEN
GREEN
Standby - ready for use
Waiting for PIN code
Weak signal
Fault
Initialising/searching
Battery low, please wait
The amber and centre green indicators provide status
information by flashing on and off in various ways. Each
complete circle below represents 2 seconds and the shaded
portions show the period that each indicator is on.
Status Indicators
Burnside Telecom Limited
Opus House, Herriard, Basingstoke,
Hampshire, RG25 2PH, United Kingdom quick start guide
Tel: [phone]
Email: [email protected]
Web: www.burnsidetelecom.com
T355 fixed cellular terminal
This quick start guide will help you to set up, switch on and begin using your T355 fixed
cellular terminal unit. For further information on all features, please refer to the full user
guide available within the ‘Service & Support’ section at: www.burnsidetelecom.com
BURNSIDE
landline alternatives

Connect the battery
Your terminal may have
been shipped with its battery
disconnected. If so, locate the
battery lead and plug it gently but
firmly into the adjacent socket (it will
fit one way only).
You can now replace the light-grey
top cover.
Connect power
1 Attach the connector from the
power adapter to the socket on
the far right of the rear panel.
2 Plug the power adapter main
body into a nearby mains outlet.
The right hand green indicator
on the front panel will light to
show when power is supplied.
Place your T355 terminal in a suitable location, but keep it at least one metre from your
telephone to avoid interference. If the signal strength is insufficient, you may need to
adjust the position of the antenna (see below).
Connect the antenna
1 Align the supplied antenna (or another suit-
able GSM antenna) with the circular connec-
tor on the far left of the rear panel.
2 Attach the antenna and twist the connector
collar clockwise until it is finger-tight - do not
overtighten.
3 In use, the antenna should always be verti-
cal. The supplied antenna has a hinge so
thatyoucanpositionitcorrectly.Whenthe
unit is wall mounted the antenna should point
straight down.
Connect a telephone
1 Connect a standard corded telephone to the
socket on the rear panel. If your phone has
a different connector than a standard RJ11
type, use an adaptor (supplied in some kits).
Switch on
On the rear panel, press and hold the red button
until the front panel amber and centre green indi-
cators illuminate, then release the button.
The centre green indicator will show a rapid on/off flash while the
terminalinitialisesitself(approx15secs).Whentheinitialisationis
complete, the T355 terminal will do one of two things:
Amber Centre
green
Right
hand
green
Centre green indicator changes to a
short flash every two seconds.
This is the ‘standby’ flash and shows that
the terminal is ready for use. Please see
the rear page for further details.
Centre green indicator extinguishes and
amber indicator shows a rapid on/off
flash.
This indicates that a PIN code is
required to unlock the SIM card.
Enter a PIN code
1 Lift the handset (you will hear a series of short tones instead of a dial tone).
2 On the telephone keypad, dial the following:
*8*[PIN code] # where [PIN code] is a valid 4-digit code for the SIM card.
• Ifthecodeisaccepted:Youwillheartwoshortbeeps,theamberindicatorwill
extinguish and the centre green indicator will show a short ‘standby’ flash every
two seconds. The T355 terminal is now ready for use, please see the rear page for
details about making and receiving calls.
• Ifthecodeisrejected: Youwillhearasinglelowpitchedbeep.Checkthat
you have the correct PIN code for the SIM card in use, replace the handset and then
try again. Note: If you enter an incorrect PIN code three times, the SIM card will lock
and you will need to get a special unblocking (PUK) code.
Black
wire
To switch off Press & hold the red button until indicators illuminate, then release.
OR