BWT BC 50 User manual

MAINTENANCE & CLEANING
0
2021/02 : A
SER MANUAL
MANUEL D’UTILISATION
BEDIENUNGSANLEITUNG
RECHARGEABLE
POOL & SPA VACUUM
ASPIRATEUR PISCINE
ET SPAS
RECHARGEABLE
WIEDERAUFLADBAR
ER POOLSAUGER

MAINTENANCE & CLEANING
1
2021/02 : A
Table Of Contents
SAFETY WARNINGS & INSTRUCTIONS P.
GETTING STARTED
P.
Charging The Battery P.
Set-Up Before Use P.
Handle assembly P.
Suction head / Corner nozzle assembly P.
Telescopic pole (not included) assembly P.
Specific Telescopic pole (not included) assembly P.
Pool Preparation P.
OPERATION
P.
EMPTYING THE FILTER BASE P.
MAINTENANCE & STORAGE
P.
BATTERY DISPOSAL
P.
How to remove the battery pack P.
TROUBLESHOOTING
P.
Remark: Product/parts photos/drawings in this manual are for demonstration only.
Product/parts in photos/drawings may vary with the model purchased.
Accessories / parts shown in this manual are not necessarily included with every
model.

MAINTENANCE & CLEANING
2
2021/02 : A
Table des matières
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS
P.
DÉBUT DES OPÉRATIONS
P.
Chargement de la batterie P.
Réglage avant l’utilisation
P.
Montage de la poignée P.
Montage de la tête d’aspiration / manchette
d’aspiration d’angle
P.
Montage du manche télescopique (non inclus) P.
Montage du manche télescopique spécifique (non
inclus)
P.
Préparation de la piscine P.
FONCTIONNEMENT
P.
VIDER LE FILTER
P.
ENTRETIEN ET STOCKAGE
P.
MISE AU REBUT DE LA BATTERIE
P.
Comment retirer le bloc de batteries P.
DEPANNAGE P.
Remarque: Les photos / dessins de produits / pièces de ce manuel sont uniquement à
titre de démonstration. Le produit / les pièces dans les photos / dessins peuvent varier
en fonction du modèle acheté
Tous les accessoires / pièces illustrés dans ce manuel ne sont pas inclus avec
chaque modèle

MAINTENANCE & CLEANING
3
2021/02 : A
Inhaltsverzeichnis
SICHERHEITSHINWEISE UND -ANWEISUNGEN
S.
ERSTE SCHRITTE
S.
Laden der Batterie S.
Vorbereitung vor der Benutzung S.
Montage des Griffs S.
Montage des Saugkopfs / Eckdüse S.
Montage der Teleskopstange (nicht inbegriffen) S.
Montage der Spezifische Teleskopstange (nicht
inbegriffen)
S.
Vorbereitung des Beckens S.
BETRIEB
S.
ENTLEEREN DES FILTERS
S.
INSTANDHALTUNG UND LAGERUNG
S.
ENTSORGUNG DES AKKUS
S.
Entfernen den Akku S.
FEHLERBEHEBUNG
S.
Kommentare Produkte/Teile auf den Fotos/Zeichnungen in dieser Anleitung dienen nur
zur Veranschaulichung. Produkte/Teile auf den Fotos/Zeichnungen können beim
gekauften Artikel variieren.
Das in dieser Anleitung gezeigte Zubehör/Teile sind nicht unbedingt bei jedem
Modell enthalten.

MAINTENANCE & CLEANING
4
2021/02 : A
SAFETY WARNINGS & INSTRUCTIONS
Information contained in this Instruction Manual will help you operate the item safely,
protect yourself and others from hazards, and prevent damage to the device and other
property.
SAVE THESE INSTRUCTIONS
WARNING!
- This is not a TOY. Children should be kept out of reach from this pool
vacuum and its accessories.
- Never allow children to operate this pool vacuum.
- This appliance is not intended for use by persons with reduced physical,
sensory, mental capabilities, or a lack of experience and knowledge,
unless they are given supervision or instructions concerning the safe use
of the appliance and understand the hazards involved by a person
responsible for their safety.
- Children must not play with this product.
- Cleaning and maintenance of the pool vacuum must not be carried out
by children.
- Make sure the pool vacuum is fully immersed in the pool before initiating
operation. The minimum water level required to operate the pool vacuum
must reach above the power ON/OFF switch of the pool vacuum when it
is held in a vertical position. Operating the pool vacuum when it is not
immersed correctly could damage the unit and void the warranty.
- Maximum operating depth in water is 3 meters (10ft).
- Maximum water temperature: 5˚C (41˚F) –35˚C (95˚F)
- Detachable supply unit (external adaptor).
- The pool vacuum should only be recharged with the external adaptor and
charging base delivered with this product.
- For the purposes of recharging the battery, only use the detachable
supply unit (external adaptor model number: DSS12D-1261000-B /
DSS12D-1261000-C / DSS12D-1261000-D/ LX135100U) that provided
with this pool vacuum to charge the battery.
- Connect the external adaptor to a power source through a residential
current device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt,
consult a qualified electrician.
- Do NOT use this pool vacuum if any damage is detected.
- Replace damaged parts with ones that are certified by the distributor or
manufacturer.
- Turn off the power, disconnect the external adaptor from the power
source, and unplug the external adaptor from the charging base before
detaching the pool vacuum from the charging base.
- Disconnect the pool vacuum from the supply mains and make sure the
pool vacuum is OFF prior to carrying out regular maintenance – such as
cleaning the filter and the charging contact plates.
- DO NOT attempt to replace the installed rechargeable Li-ion battery pack.
- DO NOT handle the pool vacuum, external adaptor, and charging base

MAINTENANCE & CLEANING
5
2021/02 : A
while it is charging with wet limbs and without shoes.
- You should not operate this pool vacuum when people/pets are present
in the water.
- DO NOT use this pool vacuum without an intact filter cone in place, as
your warranty will be voided as a result.
- Suction entrapment hazard: This pool vacuum generates suction. Do not
allow hair, body, or any loose parts of your clothing to make contact with
the suction hole of the pool vacuum during its operation.
- Never insert body parts, clothing or other objects into the openings and
moving parts of the pool vacuum.
- DO NOT use this pool vacuum to pick up any toxic substance, flammable,
and combustible liquids (i.e. gasoline) in the presence of explosive or
flammable fumes.
- Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor, and battery by yourself.
- Never insert fingers or any object to touch the impeller.
- The built-in battery must be removed by a skilled technician before it is
scrapped.
- This pool vacumm contains a battery that are only to be removed by
skilled persons.
- The pool vacumm must be disconnected from the supply mains as the
battery is removed.
- For details regarding battery recycling/disposal, refer to the section
“BATTERY DISPOSAL” in this manual and contact your local authorities
for more information.
- The battery must be disposed safely in accordance with local ordinances
or regulations.
- External adaptor and charging base:
Never use the external adaptor and charging base for anything
other than charging the battery of the pool vacuum that is
supplied in the same pack.
The external adaptor and charging base should not be used
outdoors, nor should it be exposed to rain, humidity, and any
liquid or heat.
The transformer (or external adaptor) is to be located outside
zone 1
Keep the external adaptor and charging base out of reach of
children.
Never use the external adaptor and charging base if any damage
is detected.
DO NOT handle the external adaptor and charging base with wet
hands.
DO NOT handle the pool vacuum, external adaptor, and charging
base while charging with wet hands and without shoes.

MAINTENANCE & CLEANING
6
2021/02 : A
Keep the external adaptor disconnected from power when it is
not in use.
Never attempt to open the external adaptor and charging base.
If the supply cord of the external adaptor is damaged, the external
adaptor must be replaced by the manufacturer or its service
agent to prevent hazards of any kind.
Make sure the pool vacuum and the charging base are
completely dry before charging.
CAUTION!
- This pool vacuum is designed for underwater use only; it is not an all-purpose
vacuum cleaner. DO NOT attempt to use it to clean anything other than your
pool / spa.
- Use only original accessories delivered with this product.
- DO NOT use this pool vacuum right after pool-shocking. It is recommended to
leave the pool circulating for at least 24-48 hours.
- If you are planning on using the pool vacuum in a saltwater pool, make sure
all salt are dissolved before deploying the pool vacuum.
- DO NOT use this pool vacuum with another automatic cleaner/cleaner
simultaneously in the pool/spa.
- Avoid picking up hard, sharp objects with this product. They may damage the
pool vacuum and filter.
- Exercise caution when cleaning pool stairs.
- To avoid damages to the external adaptor and charging base, do not attempt
to carry the pool vacuum by the cord of external adaptor / charging base or
pull the cord to disconnect it from the power source andcharging base.
- Charge the pool vacuum indoor in a clean, dry area with good ventilation and
an ambient temperature between 5˚C (41˚F) and 35˚C (95˚F).
- DO NOT leave the pool vacuum charged for over 10 hours.
- If the pool vacuum will not be used for an extended period, detach it from the
charging base and use a damp cloth to clean and dry the pool vacuum and
accessories. Make sure to charge the pool vacuum to about 30% to 50% of
the battery capacity before it is stored. Store in a well-ventilated area away
from sunlight, heat, ignition sources, pool chemicals, and children. Never leave
the pool vacuum plugged in for long-term storage. Recharge the pool vacuum
every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.

MAINTENANCE & CLEANING
7
2021/02 : A
GETTING STARTED
Charging the battery
IMPORTANT NOTE: Fully charge the pool vacuum (about 6 hs) before using
it for the first time.
WARNING!
Use only the original external adaptor and charging base provided.
Make sure the pool vacuum and the charging contact plates are clean
and dry before set-up and charging. (TIPS: Use a cotton bud to dry the
charging contact plates)
Charging must be done indoors, in a well-ventilated area away from
sunlight, children, heat, ignition sources, and with an ambient
temperature between 5˚C (41˚F) and 35˚C (95˚F).
Never use the external adaptor and charging base if any damage is
detected.
The charging contact plates are waterproof. However, remnants of water
on the contact plates could result in natural occurrence of stains (a
byproduct of chemical reaction between water and electric currents).
Otherwise, the stains can be removed by light scrubbing with a cotton
bud soaked with juice of lemon or vinegar.
Make sure that the pool vacuum is turned off prior to charging.
1. Place the unit on a flat surface. Make sure the pool vacuum is off by
turning the power ON/OFF switch to the OFF position prior to charging.
2. Turn the locking knob (on each side) anticlockwise until it points to the
green dot marking (unlock position) to unlock and release the rear body
from the transparent canister.

MAINTENANCE & CLEANING
8
2021/02 : A
3. Place the rear body (upside down - power on/off switch face up) on a flat
surface. Align and slide the hook of the charging base onto the side notch
at the bottom of the rear body until it stops. Make sure their contact plates
are properly in contact. Plug the female jack of the external adaptor into
the charging port at the end of the charging base.
4. Connect the external adaptor to the power source. Once the pool vacuum
begins charging, the indicator light on the external adaptor will turn red.
Normally, it takes about 5-6 hours to reach a full charge. The indicator
light will turn green when the pool vacuum is almost fully charged.
NOTE: if the motor is generating noise, ensure “OFF” is selected on the
power switch.
Immediately disconnect the external adaptor from the power source if you
detect any of the following:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
5. When charging is complete, disconnect the external adaptor from the
power source and detach the charging base from the unit and external
adaptor.
Normally, the pool vacuum can operate up to 40 minutes on a full charge (charged for 5-
6 hours)
Note: Clean the filter regularly. Too much debris inside the filter will increase burden to
the motor operation and then shorten the operating duration.

MAINTENANCE & CLEANING
9
2021/02 : A
To re-position the ransparent canister (with the filter cone inside) to the rear body, make
sure the locking knob on both sides is turned to the unlock position. Align the raised arch
on both sides of the ransparent canister with the locking knobs and then turn the knob
clockwise until it points to the red marking to secure the assembly.
Attention: The canister has one correct position only. The water-draining valve must be
facing the bottom when holding the cleaner horizontally by the handle.
FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a limited life
and will gradually lose its capacity to hold a charge. Therefore, running time of the pool vacuum
will gradually reduce through repeated charging and discharging in operation.
Once the lifespan of the battery reaches its end, refer to section “BATTERY DISPOSAL” for
instructions regarding battery disposal
NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.
Set-Up Before Use
Handle assembly
Insert the handle into the pool vacuum as shown, until the side pin on the handle is
secured to the handle’s locking hole on the rear body.
To release the handle, press down on the side pin and pull out the handle.
Suction head / corner nozzle assembly
Insert the suction head directly into the suction mouth of the pool vacuum until the side
tabs of the transparent canister clip in the side holes of the suction head.

MAINTENANCE & CLEANING
10
2021/02 : A
NOTE: To replace the brushes on the suction head, lift the end and pull it out to make
space for a new one.
WARNING! For vinyl liner and fibreglass pools/spa, it is recommended to keep the
brushes on the suction head to avoid damaging the pool/spa.
Telescopic pole (not included) assembly
Insert the end (with one side pin) of the pole connector into the pool vacuum as shown
until its single side pin is secured to the handle’s locking hole on the rear body. Slide the
telescopic pole into the pole connector until the side holes of the telescopic pole are
secured to the side pins of the pole connector.
To release the telescopic pole, press down on the two side pins simultaneously and pull
out the pole.
Pool Preparation
- If there are stones, roots or metal corrosion in contact with the underside of the liner,
discard them prior to using the pool vacuum. If necessary, seek assistance from a
qualified professional.

MAINTENANCE & CLEANING
11
2021/02 : A
- If the liner is brittle, damaged or wrinkled, contact a qualified professional to perform
the necessary repairs or perform a liner replacement prior to using the pool vacuum.
- If you are using a saltwater pool, make sure all salt are dissolved before placing the
pool vacuum into the water.
OPERATION
WARNING!
Make sure the pool vacuum is off
Do not use the pool vacuum if any damage is detected.
Oil stain could occur due to possible leakage of lubricants applied to the
O-ring.
Do not operate this pool vacuum if there are people/pets present in the
water.
Make sure the pool vacuum is fully immersed in the pool before initiating
operation. The minimum water level required to operate the pool vacuum
must reach above the power ON/OFF switch of the pool vacuum when it
is held in a vertical position. Operating the pool vacuum when it is not
immersed correctly could damage the unit and void the warranty.
DO NOT use the pool vacuum without an intact filter cone in place. Using
your pool vacuum without an intact filter cone in place will VOID your
warranty.
DO NOT cover the side slot of the vacuum during operation. The
impeller /motor may be damaged as a result.
DO NOT leave the pool vacuum in the water when it is not in use.
1) Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in
water and turn the power ON/FF switch to the ON position to initiate operation.
CAUTION! Make sure the pool vacuum is always facing downwards when it is placed into
the pool/spa. Otherwise it may bend the pole connector and damage it during the process.
2) To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing it
downwards in order to allow water to escape from the outlet valve. Water is going to
escape via the handle / pole connector and draining holes inside the handle chamber
on the rear body.
CAUTION! Make sure the pool vacuum is always facing downwards when it is removed
from the pool/spa. Otherwise, the pole connector may be bent and damage the pool
vacuum in the process
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any detergent.

MAINTENANCE & CLEANING
12
2021/02 : A
EMPTYING THE FILTER
WARNING! Using the pool vacuum without a filter cone in place will
VOID your warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter cone before and
after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the power
source and detach the pool vacuum from the charging base. Make sure the pool vacuum
is OFF
Emptying filter cone
1. Place the pool vacuum on a stable surface.
2. Turn the locking knob (on each side) anticlockwise until it is pointing towards the
green marking to unlock and release the transparent canister. Remove the
transparent canister from the rear body.
3. Tilt the transparent case and make sure the smaller end is pointing upwards, then
pull out the filter cone from the transparent canister. Hold the filter cone
horizontally and turn its lid clockwise to detach it from the cone.
4. Rinse the transparent canister and clean out the debris inside the filter cone. It is
recommended to clean the filter cone’s net with splashing water. If brushing is
deemed necessary, use only a soft brush to clean it carefully and gently. DO NOT
apply any pressure to the net.
5. To lock the lid onto the filter cone, align the slot of the lid’s edge to the tab of the
bottom part of the cone. Push the lid on the cone and turn the lid anticlockwise
until it stops. Attach the filter cone to the transparent canister.

MAINTENANCE & CLEANING
13
2021/02 : A
CAUTION! Replace a damaged filter cone immediately with a new one before the next
operation.
6. To re-position the transparent canister (with filter cone inside) onto the rear body,
make sure the locking knob on each side is turned to the unlocked position. Align the
raised arches on both sides of the transparent canister with the locking knobs and
turn each knob clockwise until it points towards the red marking to secure the
assembly. Attention: The case has one correct position only. The water-draining
valve must be facing the bottom when holding the cleaner horizontally by the handle.
MAINTENANCE & STORAGE
NOTE:
1. Be sure to clean and dry the charging contact plates after every use to avoid the
forming of stains (byproduct of a natural chemical reaction between electric current
and water). Otherwise, the stains can be removed by light scrubbing with a cotton bud
soaked with juice of lemon or vinegar.
2. Battery discharges on its own during storage. Make sure to charge the pool vacuum
to about 30% to 50% of the battery capacity before it is stored.
3. You must re-charge the battery at least once every three months when it is not in use.
Unplug the external adaptor from socket and then unplug the adapter jack from the
charging base.
Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and
accessories with fresh water. DO NOT use detergent.
Make sure to drain the water from the rear body through the holes located inside
the chamber that connects to the handle/ pole connector, and the hole on the rear
of the body.

MAINTENANCE & CLEANING
14
2021/02 : A
Make sure to drain the water from the handle through its hole on the bottom end.
Use a damp cloth to clean and dry the pool vacuum and its accessories.
Store them in a well-ventilated area away from the sunlight, children, heat, ignition
sources, and pool chemicals. Ambient temperature for storage should be 10˚C – 25˚C
(50˚F – 77˚F). NOTE: A higher temperature may reduce the battery life during storage.
WARNING!
-Never attempt in any way to disassemble the pool vacuum.
-Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor and battery by yourself.
CAUTION!
Excessive heat can damage the battery and reduce its lifespan as a result.
Consult your dealer regarding battery replacement if the following happens:
-Battery does not charge fully.
- Battery operation time is noticeably reduced. Observe and record the run times of the
first few operations (on a full charge). Use these run times as a reference point for
comparison with run times in the future.
The battery must be removed from the pool vacuum before it is scrapped.
The pool vacuum must be disconnected from the supply mains when removing the
battery
The battery is to be disposed safely and according to local ordinances or regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a
result.
BATTERY DISPOSAL (To be carried out by an authorized technician)
Your pool vacuum battery is a maintenance-free rechargeable lithium-ion battery pack,
which must be disposed properly. Recycling is required; please contact your local
authority for information.
WARNING!Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces and
watches when the battery pack is unwired from the pool vacuum.
A battery can produce a short circuit current high enough to weld a ring
(or similar item) to metal, causing a severe burn in the process.
Wear complete eye protection, gloves and protective clothing when the
battery pack is being removed.
Avoid touching the wires altogether and avoid allowing them to make

MAINTENANCE & CLEANING
15
2021/02 : A
contact with any metal items, which could cause sparking and/or short
circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the
pool vacuum.
Do not expose the battery to fire or intense heat as this may result in an
explosion.
CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with plenty
of soap and water.
-If leaking fluids come in contact with eyes, immediately flush eyes with cool running
water for at least 15 minutes and do not rub them. Seek medical attention as soon as
possible.
How to remove the battery pack for battery disposal only (To be done by
authorized technician)
Recommended tools (not included): Philips screwdriver
1. Turn the locking knob (on each side) anticlockwise until it points to the
green dot marking (unlock position) to unlock and release the rear body
from the transparent canister.
2. Use the screwdriver to unscrew the 4 screws located on the top plate and
then detach it from the rear body to expose the rear body’s cover.
3. Unfasten 6 screws and detach the cover to expose the PCBA, motor
assembly, and battery pack.
4. To detach the battery connection wire, press the clip on the connector and
then pull it out.

MAINTENANCE & CLEANING
16
2021/02 : A
5. Unfasten the 3 screws to remove the battery compartment cover and
then remove the battery pack. NOTE: Wrap the connector immediately
with insulating tape in order to avoid short circuit caused by contact of
both wire terminals.

MAINTENANCE & CLEANING
17
2021/02 : A
TROUBLESHOOTING
Problem
Possible Cause
Solution
Pool vacuum does not capture the
debris
Battery is running out
Charge the battery again.
Impeller is jammed
Power off the pool vacuum and visually check the
gap in middle of the pool vacuum to see if the
impeller is jammed by larger debris. If possible, use a
small tool to remove it with intensive care & caution.
If necessary, contact your dealer for further
instructions.
WARNING! Make sure the pool vacuum is
powered off when the unit is being serviced.
Impeller is broken
Contact your dealer for impeller replacement.
Filter is full
Clean the filter cone if applicable.
Larger debris / large
volume of debris
Remove the pivoting suction head (not
recommended for SPAs as it could scratch the spa
surface.)
Debris escapes from the filter
Suction nozzle flap is
broken
Suction nozzle flap works like a door to prevent the
debris from escaping from the filter. Contact dealer
for replacement parts and instruction.
Debris goes outside the filter cone
Filter net is damaged
Replace with a new filter cone.
Outlet valve comes off
Without the outlet valve, the pool vacuum might
capture debris through this opening. Contact dealer
for valve replacement.
Handle / pole connector cannot be
secured in assembly
Side pin is broken
Replace with a new handle / pole connector.
Pool vacuum cannot be charged /
recharged
Battery is damaged
Contact dealer for battery replacement.
WARNING! DO NOT open the pool vacuum
and replace the battery by yourself. This could result
in severe or fatal injuries and the warranty will be
voided as a result.
Contact plates of the
charger base and unit are
not connected.
Make sure that the charger base is assembled on the
unit properly so that their contact plates are touching.
External adaptor is out of
order
Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the pool vacuum / battery and
voiding the warranty as a result.
Suction head does not move
smoothly
Wheel is jammed
Clean out the debris from the wheel.
Pool vacuum is activated even
though the switch indicates it’s off.
Presence of magnetic
objects nearby has
inadvertently switched on
the motor.
Move the magnetic objects or vacuum away from
each other.
Operation time is shorter as
expected
Battery is not fully charged
Charge the pool vacuum for at least 6 hrs. NOTE: if
any stains are found on the charging contact plates,
remove them by using a cotton bud soaked with
lemon juice or vinegar
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that properly
recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For items
containing removable batteries, remove batteries before disposing of the product.
© 2020
BWT Holding GmbH
20011012
All rights reserved. No part of this document may be reproduced or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission. (V2)
If soft copy of this instruction manual is required, please contact our customer service by email.
SAVE THESE INSTRUCTIONS

MAINTENANCE & CLEANING
18
2021/02 : A
AVERTISSEMENTS DE SÉCURITÉ ET INSTRUCTIONS
Les informations contenues dans ce manuel d'instructions vous permettront d’utiliser
l’appareil en toute sécurité, à vous protéger ainsi que les autres et à éviter d'endommager
l'appareil ou d'autres biens.
CONSERVER CE MANUEL
AVERTISSEMENT !
- Ceci n’est pas un JOUET. Les enfants doivent être maintenus hors de la
portée de cet aspirateur de piscine et de ses accessoires.
- Ne jamais permettre aux enfants de faire fonctionner ce aspirateur de
piscine.
- Ce dispositif n'est pas destiné à être utilisé par des personnes ayant des
capacités physiques, sensorielles ou mentales diminuées, ou un manque
d'expérience et de connaissances, sauf si elles sont sous supervision ou
ont reçu des instructions concernant l'utilisation sûre de l'appareil par une
personne responsable de leur sécurité.
- Les enfants ne doivent pas jouer avec ce aspirateur de piscine..
- Le nettoyage et l'entretien du aspirateur de piscine ne doit pas être
effectués par des enfants.
- Assurez-vous que l’aspirateur de piscine est totalement immergé dans la
piscine avant de commencer l’opération. Le niveau d’eau minimum exigé
pour faire fonctionner l’aspirateur de piscine doit dépasser l’interrupteur
Marche / Arrêt de l’aspirateur de piscine lorsqu’il est maintenu en position
verticale. Faire fonctionner l’aspirateur de piscine lorsqu’il n’est pas
immergé correctement pourrait endommager l’unité et annuler la
garantie.
- La profondeur maximale de fonctionnement dans l’eau est de 3 mètres
(10 pieds).
- Température maximale de l’eau : 5˚C – 35˚C
- Unité d'alimentation détachable (transformateur).
- À l’effet de recharger la batterie, utiliser seulement l’unité d’alimentation
amovible (DSS12D-1261000-B / DSS12D-1261000-C / DSS12D-
1261000-D/ LX135100U) qui est fourni avec cet aspirateur de piscine
pour charger la batterie.
- Pour recharger la batterie, utilisez uniquement l'unité d'alimentation
amovible (transformateur) fournie avec ce produit
- Connecter le transformateur à une source d'alimentation par
l'intermédiaire d'un dispositif différentiel à courant résiduel (DDR) ou d'un
disjoncteur de fuite à la terre (GFCI). En cas de doute, consultez un
électricien professionnel qualifié.
- Ne pas utiliser cet aspirateur de piscine si un dommage quelconque est
détecté.
- Remplacer les pièces endommagées avec des pièces certifiées par le
distributeur ou le fabricant.
- Mettre hors tension, débrancher le transformateur de la source
d’alimentation, et débrancher le transformateur de la base de
chargement avant de séparer l’aspirateur de piscine de la base de
chargement.

MAINTENANCE & CLEANING
19
2021/02 : A
- Débrancher l’aspirateur de piscine du réseau d’alimentation et s’assurer
que l’aspirateur de piscine est hors tension avant d’effectuer l’entretien
régulier – tel que le nettoyage du filtre et des plaques de contact de
chargement.
- Ne remplacez pas la batterie rechargeable Li-ion pré-installée.
- NE manipulez PAS le aspirateur de piscine, le transformateur et la base
de chargement pendant la charge avec des membres mouillés et sans
chaussures.
- Vous ne devrez pas faire fonctionner cet aspirateur de piscine lorsque
des personnes/animaux de compagnie sont présents dans l’eau.
- Ne pas utiliser cet aspirateur de piscine sans une cône filtrant intact en
place, car votre garantie serait annulée de ce fait.
- Danger de piégeage de l’aspiration : Cet aspirateur de piscine produit
une aspiration. Ne pas permettre que les cheveux, le corps, ou toutes
parties lâches de vos vêtements entrent en contact avec l’orifice
d’aspiration de l’aspirateur de piscine pendant son fonctionnement.
- Ne jamais introduire des parties du corps, vêtements ou autres objets
dans les ouvertures et pièces mobiles de l’aspirateur de piscine.
- NE PAS utiliser cet aspirateur de piscine pour ramasser des substances
toxiques, inflammables ou liquide combustibles (comme de l'essence),
ni en présence de vapeurs explosives ou inflammables.
- En aucun cas, vous ne devrez tenter de démonter l’aspirateur de piscine
et de remplacer la turbine, le moteur, et la batterie de par vous-même.
- Ne jamais insérer les doigts ou un quelconque objet dans la turbine.
- La batterie intégrée doit être retirée par un technicien qualifié avant d'être
mise au rebut.
- Cet aspirateur de piscine contient une batterie qui ne peut être retirée
que par des personnes qualifiées.
- L’aspirateur de piscine doit être déconnecté du réseau d'alimentation lors
du retrait de la batterie.
- Pour plus de détails sur la mise au rebus de la batterie veuillez vous
reporter à la section "MISE AU REBUT DE LA BATTERIE" de ce manuel
et contactez les autorités locales pour plus d'informations.
- La batterie doit être détruite en toute sécurité conformément aux
réglementations locales.
- La transformateur et base de chargement :
Ne jamais utiliser le transformateur et la prise de chargement/base de
chargement pour tout autre chose que le chargement de la batterie de
l’aspirateur de piscine qui est fournie dans le même bloc.
Le transformateur et la base de chargement ne doivent pas être utilisés
à l'extérieur, ni exposés à la pluie, à l'humidité et à tout liquide ou
chaleur.
Le transformateur doit être situé à l'extérieur de la zone 1
Maintenir le transformateur et la base de chargement hors de la portée
des enfants.
Ne jamais utiliser le transformateur et la base de chargement si un
dommage quelconque est détecté.