C.Nord Rielta CN-Siren User manual

WIRELESS SOUNDER
«CN-Siren»
Installation Guide
The sounder displays one of it’s operation modes as specified in
Table 3 (LED indication).
5 Sounder Design
The sounder outside view is shown in Figure 1.
The sounder consists of a base (1) and case (4). The base comprises
the oval holes (2) for it’s fastening to the mounting surface. The case
is fastened to the base with latches (3).
There is a two-color LED indicator (5) on the front surface of the
case. There are contacts (6), the main power-supply battery holder
(7) and the backup power-supply battery holder (8).
1 Product Overview
1.1 Wireless sounder «CN-Siren» (hereinafter, the sounder) is
intended for informing people about a fire or other emergencies by
generating an audible alarm.
1.2 The sounder is intended for operation as a component of a
system that is operated by a control panel (hereinafter, CP), supporting
«CN-Contact-R» wireless two-way data exchange protocol.
1.3 The sounder is switched on and off by means of CP, and it’s
operation modes are assigned by commands from the CP.
1.4 The sounder monitors and transmits messages upon removal
from it’s base or upon discharge of both main and backup batteries.
1.5 The following rates of control radio exchange may be assigned:
10, 15, 30, 60 sec, 5 or 10 min.
1.6 The sounder can operate in a continuous or pulsed audible-alarm
modes.
1.7 Pulse-mode parameters can be set by the user in the process
of the sounder adjustment.
1.8 The sounder operation mode is displayed by a two-color LED
indicator.
1.9 Two frequencies in the 433.05 to 434.79 MHz frequency range
are used for wireless signal exchange with the CP – the main frequency
and the reserve one. The sounder swithes to the reserve operating
frequency automatically in case of radio-frequency interference on the
main one. Transmitter power does not exceed 10 mW.
1.10 The sounder is powered by two CR123A batteries, the main
and the backup one.
1.11 The batteries’ respective service-time capacities in a standby
mode (with a signal-monitoring interval of at least 30 sec) are as follows:
- main power-supply battery – at least 60 months or at least 2 months
in continuous operation mode;
- backup power-supply battery – at least 2 months.
1.12 The sounder is designed to operate continuously around the
clock in closed premises of residential and industrial buildings and
structures.
1.13 The sounder is resistant to the impact of electromagnetic
interference.
2 Principal Technical Characteristics
Table 1
Features Value
Acoustic pressure level at 1 m distance from the
sounder, not less than 85 dB
Generated alarm signals frequency 2000 to 4000 Hz
Operating temperature from minus 20 to +55 °С
Permissible humidity (at temperature 35 °C): 93 %
IP rating IP40
Dimensions, max ⊘
121 x 54 mm
Weight (without power-supply batteries), max 0.2 kg
Battery life, not less than 10 years
3 Scope of Delivery
Each sounder unit package contains the items listed in Table 2.
Table 2
Name Qty
«CN-Siren» wireless sounder
Screw 3-3x30.016
Wall plug NAT 5x25 SORMAT
CR123A lithium power-supply battery
«CN-Siren» wireless sounder. Installation Guide
1 pc.
2 pcs.
2 pcs.
2 pcs.
1 copy
4 Informativity
The sounder generates and transmits the following messages to the
CP via wireless communication:
- «Norm»;
- «Tampering»;
- «Main power-supply low-battery» – if power-supply voltage drops
below (2.4 ± 0.2) V during a regular communication session;
- «Backup power-supply low-battery» – if power-supply voltage
drops below (2.4 ± 0.2) V during a regular communication session;
Figure 1
6 LED Indication
Table 3
Sounder Status LED Indication
«Binding» mode LED indicator blinking green
«Binding is completed»Short-term (2 sec) LED indicator lighting red
«Identification» LED
indication
Alternate LED indicator lighting green and red
«Communication
Quality Appraisal»See Table 4
7 Switching On and Setting Up
7.1 Remove the sounder from it’s base.
7.2 Install the main power-supply battery and the backup one.
7.3 Provide a tmporary connectionbetween the «-» contact of either
power-supply battery holder and contact «4» on the sounder base.
7.4 Make sure the LED indicator is blinking green (binding mode).
7.5 Perform the procedure of the sounder binding to the CP in
accordance with the CP operation manual.
7.6 Make sure that the LED indicator blinked red once for a
moment.
Note – The binding mode is active for 100 sec. Sect. 7.3 should
be repeated in order to resume the binding procedure.
8 Installation Recommendations
8.1 Appraise communication quality at the place where you intend
to install the sounder (see Sect. 9).
8.2 Install the sounder at a place where communication quality is
appraised as «excellent» or «good».
8.3 Install the base at the chosen location.
8.4 Make sure that the base contacts 2 and 3 are closed with a
wire jumper.
8.5 Insert the sounder into the base and lock it by turning clockwise
to it’s fully latched position.
9 Communication Quality Appraising
9.1 Insert the sounder into the base and lock it by turning clockwise
to it’s fully latched position. Wait for 3 sec.
9.2 Remove the sounder from the base and appraise communication
quality by means of LED indication as shown in Table 4.
Note – The delay up to 4 sec between tampering and LED
indication switching is possible.
5
7
8
9
1 2 3 46

12 Manufacturer’s Guarantees
12.1 «RIELTA» JSC guarantees conformity of the Detector to it’s
Technical Specifications if conditions of transportation, storage,
assembling and operation are observed. The guaranteed storage
period is 63 months since the date of manufacturing the Detector.
12.2 The guaranteed period of operation is 60 months since the date
of commissioning within the storage period guaranteed.
12.3 For guaranteed maintenance, please contact:
«С.Nord» STCF
Russia, 190020, St. Petersburg,
Obvodny Channel emb., 199-201, build.13, BC «Obvodny Dvor»
Phone: [phone]
E-mail: [email protected], [email protected], www.cnord.ru
Note – Warranty obligations are not applied to the power-supply
batteries.
13 Packing Certificate
Wireless sounder «CN-Siren» wireless sounder has been
manufactured in compliance with the active technical documentation,
classified as fit for operation and packed by «RIELTA» JSC.
Person responsible for acceptance and packing
QC representative_________________ __________________.
Date, month, year
Table 4
LED indication Communication
Quality
Appraisal
Recommendations
Color Mode
Green Three blinks Excellent Install the sounder
at this place
Green Two blinks Good
Green One blink Communication
established Choose another
place for installation
or use a repeater*)
Red A series of
blinks No communication
*) – «CN-Repeater»
10 Features and Recommendations
10.1 The sounder is powered on and off by installation and removal
of the main and the backup power-supply batteries.
10.2 In case of main power-supply low-battery, the sounder
switches to the backup one. The sounder does not operate when the
main power-supply battery is not installed.
10.3 Replace both batteries if any of them is discharged.
10.4 The installed power-supply batteries must be of the same
type. The backup battery should be installed first.
In case the CP is disabled for a long time, it is recommended to
power off the sounder.
11 Storage and Transportation
11.1 The sounders in their original packaging may be transported
by any means of transportation in closed vehicles over any distances
in compliance with the existing shipping rules concerning the
respective means of transportation.
11.2 The storage premises should not contain any current-
conducting dust, acid and alkali fumes, or corrosive or destroying
insulation gases.
Rev. 1 of 06.06.16
№ 00235
By order of «С.Nord» STCF, www.cnord.ru
Russia, 190020, St. Petersburg,
Obvodny Channel emb., 199-201, build.13, BC «Obvodny Dvor»,
Phone: [phone], [email protected]
Technical support: [email protected], http://support.cnord.ru
Made in Russia
The Manufacturer: «RIELTA» JSC, www.rielta.com
Russia, 197101, St. Petersburg, Chapaeva str., 17
Phone /fax: [phone], [email protected]
Technical support: phone [phone], [email protected]