Cable Prowler CB300 User manual

Quick Start Guide
Full Color Cable Testing
& Report Management
CB300
CB350
CB400
www.T3Innovation.com
CAT 3/5e/6/6a
Coax
Telephone Cable

2Cable Prowler Quick Start Guide
Network Cable Test Coax Cable Test Telephone Cable Test
Test
On/Off
Direction cursors to
move in LCD display
Enter
Back
Micro USB Port
RJ45 jack
F-connector Jack
Soft keys perform the
function on the display
above each button.

T3 Innovation 3
How to Perform a Cable Test
 Power on the Cable Prowler.
 Connect a network, coax, or telephone cable to the appropriate
connector on the top of the Cable Prowler.
(Warning! Do not plug an RJ11 cable directly into the Cable Prowler! A
standard RJ11 cable will damage the Cable Prowler’s RJ45 jack. Use the
included RJ adapter patch cable (CA012) that is included with the cable
Prowler.)
 Press the enter button to display the cable test menu. The Cable
Prowler will automatically perform a test upon entering the cable test
menu.
 To test coax or telephone cable, press the coax or telephone soft key.
 If a remote is NOT being used (one ended test), the Cable Prowler will
test the length of each pair, opens, shorts, or split pairs. Performing a
one ended test will not verify connectivity on the opposite end of the
cable.
 If a remote is being used, connect the remote to the opposite end of the
cable.
 To calibrate the VOP, connect a known length of cable to the Cable
Prowler and press the up/down/left/right buttons to increase or
decrease the VOP. Press the left and right buttons to select and change
the VOP one digit at a time.
 While adjusting the VOP, press the test button every so often until the
length of the cable is displayed.
 Press the green test button or the loop mode soft key to
perform additional tests.
 To save a cable test, press the save icon.



4Cable Prowler Quick Start Guide
 Power on the Cable Prowler.
 Connect the Cable Prowler to a switch or active network jack.
 Use the left or right arrow buttons to select the Network/PoE icon
and press the enter button or press the Network/POE soft key.
 The Cable Prowler will automatically detect and display link capability,
connection speed, PoE class, and PoE Min/Max voltages.
 To perform a Network Test only, press the PoE soft key.
 To save the PoE data, press the Save soft key.


Network / PoE Detection

T3 Innovation 5
 Power on the Cable Prowler.
 Connect the Cable Prowler to an active Network cable or port.
 Press the Network/Poe soft key then press the Link Light soft key.
 The Link Light will automatically begin upon entering the Link Blink menu.

port light.
 Use the up and down arrows to adjust the transmit frequency to suit the
switch characteristics.
Link Light

6Cable Prowler Quick Start Guide
 Power on the Cable Prowler.
 Use the left or right arrow buttons to select the tone generator icon
and press the enter button.
 The cable prowler will automatically activate the tone generator upon
entering the tone generator menu.
 Connect your cable to either the RJ45 jack or coax connector located on the
top of the Cable Prowler.
 To switch between network and coax cables, press the coax cable/RJ45
soft key / .
 Press the up or down arrow buttons to select tone cadences 1 thru 4.
 Press the left or right arrow buttons to select which pin or pair to place the
tone.
 Use a tone probe (P/N TP200 TrakAll) alongside the cable or at the end of
the cable to hear an audible tone.
Tone Generator

T3 Innovation 7
 Press the setup softkey to enter the setup menu.
 Use the up and down buttons to select a setting.
 Use the left and right arrow buttons to change the selected setting.
 Press the save soft key to save changes.
 Press the defaults soft key to reset the settings to factory settings.
 Press the Files soft key to view stored test results.
See http://T3Innovation.com/downloads to install Cable Prowler software and
learn how to transfer your test results to your PC.
Setup
Cable Prowler Software Application

Product Kits
For complete Cable Prowler user manual, technical
information and customer support, please visit
www.t3innovation.com or send an email
to [e-mail].
Contact Numbers: Phone: [phone]
Fax: [phone]
Address: 808 Calle Plano
Camarillo, CA 93012
www.T3Innovation.com
CB300
• Cable Prowler Main Unit
• Coax and Network Remote Set:
#1-5, F-Conn coupler includes foam holder
• Network/Tel Testing and ID Remote #1
• RJ12 Cable – Qty 2
• Micro USB Cable
• Hanging T3 Pouch
CB350
• Cable Prowler main Unit
• Coax and Network Remote Set:
#1-5, F-Conn coupler includes foam holder
• #1-8 Network/Tel Testing and ID Remotes
• RJ12 Cable – Qty 2
• Micro USB Cable
• Large T3 Pouch
CB400
• Cable Prowler Main Unit
• #1-8 Network/Tel Testing and ID Remotes
• #1-20 Coax Remotes
• #1-20 Network Remotes
• RJ12 Cable – Qty 2
• TrakAll – Tone and Probe
• Micro USB Cable
• Large T3 Pouch
Made in USA
With Global Components