Cabletron Systems MicroMMAC 22ES User manual

MicroMMAC
LOCAL MANAGEMENT
USER’S GUIDE

MicroMMAC Local Management User’s Guide i
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
 Copyright 1996 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Order Number: 9031838-01 June 1996
SPECTRUM , LANVIEW , MicroMMAC , and BRIM are registered trademarks and Element
Manager , EPIM , EPIM-A , EPIM-F1 , EPIM-F2 , EPIM-F3 , EPIM-T , EPIM-X , FOT-F , FOT-F3 ,
HubSTACK , SEH , SEHI , and TMS-3 are trademarks of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
Printed on Recycled Paper

Notice
ii MicroMMAC Local Management User’s Guide
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
DOC NOTICE
This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
VCCI NOTICE
This equipment is in the 1st Class Category (information equipment to be used in commercial and/or
industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial
and/or industrial areas.
Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be
caused to radios and TV receivers, etc.
Read the instructions for correct handling.

Notice
MicroMMAC Local Management User’s Guide iii
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT: Before utilizing this product, carefully read this License Agreement.
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (the
“Program”) contained in this package. The Program may be contained in firmware, chips or other
media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
CABLETRON SOFTWARE PROGRAM LICENSE
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including
its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE
ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,
EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR
ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.

Notice
iv MicroMMAC Local Management User’s Guide
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer
software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the
Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects
is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the
DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its
successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

MicroMMAC Local Management User’s Guide v
CONTENTS
CHAPTER 1 INTRODUCTION
1.1 Using This Manual.......................................................................1-1
1.2 Manual Organization ...................................................................1-1
1.3 Local Management Overview......................................................1-2
1.3.1 The Management Agent .................................................1-2
1.3.2 In-Band vs. Out-of-Band.................................................1-3
1.3.3 Local vs. Remote Management......................................1-3
1.4 Local Management Requirements...............................................1-3
1.5 Local Management Screen Elements..........................................1-4
1.6 Local Management Keyboard Conventions.................................1-6
1.7 Navigating Local Management Screens......................................1-7
1.8 Document Conventions...............................................................1-8
1.9 Related Documents.....................................................................1-8
1.10 Getting Help.................................................................................1-8
CHAPTER 2 LOCAL MANAGEMENT REQUIREMENTS
2.1 Configuring a Local Management Terminal.................................2-1
2.2 Management Terminal Setup Requirements...............................2-2
2.2.1 Cable Configuration for the Management Terminal........2-3
2.2.2 Cable Configuration for the UPS ....................................2-4
2.3 Establishing a Telnet Connection................................................2-4
CHAPTER 3 ACCESSING LOCAL MANAGEMENT
3.1 Using the Menu Screens.............................................................3-1
3.2 Navigating Local Management Screens......................................3-2
3.2.1 Selecting Local Management Menu Screen Items .........3-3
3.2.2 Exiting Local Management Screens ...............................3-4
3.2.3 Exiting the Local Management Session..........................3-4
3.3 The Main Menu Screen...............................................................3-5
3.4 The Setup Menu Screen..............................................................3-6
3.5 The Status Menu Screen.............................................................3-7

Contents
vi MicroMMAC Local Management User’s Guide
CHAPTER 4 SYSTEM LEVEL SCREEN
4.1 System Level Screen Fields ........................................................4-2
4.2 Setting the System Date ..............................................................4-4
4.3 Setting the System Time..............................................................4-5
4.4 Setting the Host IP Address.........................................................4-5
4.5 Setting the Out of Band IP Address.............................................4-6
4.6 Setting the Default Gateway........................................................4-6
4.7 Setting the Subnet Mask..............................................................4-7
4.8 Setting the Default Interface ........................................................4-7
4.9 COM Port Applications.................................................................4-8
4.9.1 Configuring the COM Ports.............................................4-8
4.9.2 Configuring the COM Port Baud Rate.............................4-9
CHAPTER 5 SNMP COMMUNITY NAMES SCREEN
5.1 Community Name Access Policy.................................................5-2
5.2 Setting SNMP Community Names...............................................5-2
CHAPTER 6 SNMPTRAPS SCREEN
6.1 Trap Table Screen Fields.............................................................6-2
6.2 Setting the SNMP Trap Destination.............................................6-2
CHAPTER 7 FLASH DOWNLOAD SCREEN
7.1 Selecting a Flash Download Method ...........................................7-2
7.1.1 Runtime Download..........................................................7-2
7.1.2 Bootprom Download........................................................7-3
CHAPTER 8 BRIDGE SETUP SCREEN
8.1 Bridge Setup Screen Fields .........................................................8-2
8.2 Selecting a Spanning Tree Protocol ............................................8-2
8.3 Selecting the Port Administrative Status......................................8-3
8.4 Selecting the Bridge Port Pair Administrative Status...................8-4
CHAPTER 9 COMPONENT STATUS SCREEN
CHAPTER 10 BRIDGE STATISTICS SCREEN
10.1 Bridge Statistics Screen Fields ..................................................10-1
10.2 Selecting an Update-Freq..........................................................10-4
10.3 Selecting an Interface/Module/Port............................................10-4
10.4 Enabling Ports............................................................................10-5
10.5 Disabling Ports...........................................................................10-5

Contents
MicroMMAC Local Management User’s Guide vii
CHAPTER 11 MIB NAVIGATOR SCREEN
11.1 Managing Device MIBs..............................................................11-2
11.2 MIB Navigator Command Set Overview....................................11-3
11.2.1 Conventions for MIB Navigator Commands .................11-4
11.2.2 Navigation Commands .................................................11-5
11.2.3 Other Commands .......................................................11-11
11.2.4 Special Commands.....................................................11-17

Contents
viii MicroMMAC Local Management User’s Guide

MicroMMAC Local Management User’s Guide Page 1-1
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems MicroMMAC Local Management
User’s Guide
. This manual explains how to access and use Cabletron
Systems Local Management for the MicroMMAC. Local Management
provides monitoring and control services for the MicroMMAC and its
attached segments.
1.1 USINGTHIS MANUAL
A general working knowledge of basic network operations and an
understanding of management applications is helpful prior to using
Cabletron Systems Local Management.
This manual describes how to:
• Access the Local Management application
• Identify and operate the types of fields used by Local Management
• Navigate through Local Management fields and menus
• Use Local Management screens to perform management operations
1.2 MANUAL ORGANIZATION
The following summarizes the organization of this manual.
Chapter 1,
Introduction , outlines the contents of this manual, provides an
overview of Local Management, and explains how to use the management
screens.
Chapter 2,
Local Management Requirements , describes the setup
requirements for accessing Local Management. It also explains how to
configure a management terminal and connect it to the MicroMMAC.
Chapter 3,
Accessing Local Management , describes how to access the
Main Menu screen and navigate the Local Management screens.
Chapter 4, System Level Screen , describes how to use the System Level
screen, its functions, and operations.

Chapter 1: Introduction
Page 1-2 MicroMMAC Local Management User’s Guide
Chapter 5, SNMP Community Names Screen , explains how to control
access to the MicroMMAC by assigning community names.
Chapter 6, SNMP Traps Screen , explains how to configure the
MicroMMAC to send SNMP traps to multiple network management
stations.
Chapter 7,
Flash Download Screen , describes how to download a new
firmware image to the MicroMMAC.
Chapter 8, Bridge Setup Screen , describes how to configure the
MicroMMAC for bridge functions.
Chapter 9, Component Status Screen , discusses how to view the status
of MicroMMAC MIB components.
Chapter 10, Bridge Statistics Screen , discusses how to configure the
MicroMMAC to gather statistics for each interface, module, and port.
Chapter 11, MIB Navigator Screen , describes how to access and use the
MIB Navigator screen. This chapter also includes examples for MIB
Navigator commands.
1.3 LOCAL MANAGEMENT OVERVIEW
Cabletron Systems Local Management is a management tool that allows a
network manager to perform the following tasks:
• Configure interconnected devices to form a network
• Monitor the performance of the network
• Control user access to the network and its components for the purpose
of security
1.3.1 The Management Agent
The management agent is a processor within the MicroMMAC which
collects statistical information (e.g., frames received, errors detected)
about the managed network’s operational performance. Local
Management communicates with the management agent for the purpose
of viewing statistics or issuing management commands to network
devices.

Local Management Requirements
MicroMMAC Local Management User’s Guide Page 1-3
1.3.2 In-Band vs. Out-of-Band
Network management systems are often classified as either in-band or
out-of-band. In-band network management passes data along the same
medium (cables, frequencies) used by all other stations on the network.
An example of an in-band network management system is Cabletron
Systems SPECTRUM.
Out-of-band network management passes data along a medium that is
entirely separate from the network’s common data carrier, for example, a
cable connection between a dumb terminal and the COM port of the
MicroMMAC. Cabletron Systems Local Management is an out-of-band
network management system.
A device connected out-of-band to the management agent is not
connected to the LAN. This type of connection allows you to
communicate with a network device even when that device is unable to
communicate through the network, for example, at the time of
installation.
1.3.3 Local vs. Remote Management
Network management applications are usually described as either local or
remote management applications. Local management applications reside
within the circuits of the management device’s management agent.
Remote management applications run within the circuits of another
device that provides management services. This allows you to perform
network management from a remote location.
1.4 LOCAL MANAGEMENT REQUIREMENTS
The MicroMMAC provides two communication ports. Each port supports
a management terminal connection. To access Local Management,
connect one of the following systems to either COM 1 or COM 2:
• Digital Equipment Corporation VT series terminal
• VT type terminal running emulation programs for the Digital
Equipment Corporation VT series
• IBM or compatible PC running a VT series emulation software
package
You can also access Local Management using a Telnet connection
through one of the network ports of the MicroMMAC.

Chapter 1: Introduction
Page 1-4 MicroMMAC Local Management User’s Guide
1.5 LOCAL MANAGEMENT SCREEN ELEMENTS
Local Management screens consist of five basic elements, or fields.
Figure 1-1 shows a Local Management screen and points out the various
types of fields.
Figure 1-1 Sample Local Management Screen
COM 1Application:
SYSTEM LEVEL
System Date:
Host IPAddress 000.000.000.000
Subnet Mask 255.255.0.0
Phys Address 00-00-1D-16-26-F8
COM 2Application: [UNASSIGNED]
[LM]
01/23/96 System Time:
SAVE RETURN
090836
Out of Band IPAddr 0.0.0.0
Default Gateway NONE DEFINED
Default Interface NONE DEFINED
COMMAND FIELDS
DISPLAY FIELDS
INPUT FIELDS
14:23:00
SELECTION FIELDS
EVENT MESSAGE FIELD
MicroMMAC Local Management Flash Image Version XX.XX.XX
SAVED OK

Local Management Screen Elements
MicroMMAC Local Management User’s Guide Page 1-5
The following list explains each of the Local Management fields:
Event Message Field
This field briefly displays messages that indicate if a Local Management
procedure was executed correctly or incorrectly, that changes were saved
or not saved to Non-Volatile RandomAccess Memory (NVRAM), or that
a user did not have access privileges to an application.
Table 1-1 describes the most common event messages. Event messages
related to specific Local Management applications are described with
those applications throughout this manual.
Display Fields
Display fields can not be edited. These fields may display information
which never changes, or information which may change as a result of
Local Management operations, user selections, or network monitoring
information.
Input Fields
Input fields require the entry of keyboard characters. IP addresses, System
Date, and System Time are examples of Input fields.
Selection Fields
Selection fields provide a series of possible values. Only applicable values
appear in selection fields.
Command Fields
Command fields are located at the bottom of Local Management screens.
Command fields are used to exit Local Management screens and to save
Local Management entries.
Table 1-1 Event Messages
Message Meaning
SAVED OK One or more fields were modified,
and saved to NVRAM.
NOT SAVED?--PRESS SAVE TO
KEEP CHANGES One or more fields were modified, but not yet saved to NVRAM.
NOTHING TO SAVE The SAVE command was executed,
but nothing was saved to NVRAM.

Chapter 1: Introduction
Page 1-6 MicroMMAC Local Management User’s Guide
1.6 LOCAL MANAGEMENT KEYBOARD CONVENTIONS
All key names appear in this manual as capital letters. For example, the
Enter key appears as ENTER, the Escape key appears as ESC, and the
Backspace key appears as BACKSPACE. Table 1-2 explains the keyboard
conventions used in this manual as well as the key functions.
Table 1-2 Keyboard Conventions
Key Function
ENTER and RETURN These are selection keys that perform
the same Local Management
function. For example, “Press
ENTER” means that you can press
either ENTER or RETURN, unless
this manual specifically instructs you
otherwise.
ESC This key lets you escape from a Local
Management screen without saving
your changes. For example, “Press
ESC twice” means that you must
quickly press the ESCAPE key two
times to exit the Local Management
screen.
SPACE and BACKSPACE These keys cycle through selections
in some Local Management fields.
Press SPACE to cycle forward
through selections and Press
BACKSPACE to cycle backward
through selections.
Arrows These are navigation keys.Use the
UP-ARROW, DOWN-ARROW,
LEFT-ARROW, and RIGHT-ARROW
keys to move the screen cursor. For
example, “Use the arrow keys”
means to press whichever arrow key
moves the cursor to the desired field
on the Local Management screen.
SHIFT-[+/=] This key combination increments values in some Local Management
selection fields.For example, “Press
SHIFT-[ +/= ]” means to hold down the
SHIFT key while pressing the
PLUS/EQUAL key.

Navigating Local Management Screens
MicroMMAC Local Management User’s Guide Page 1-7
1.7 NAVIGATING LOCAL MANAGEMENT SCREENS
To navigate within a Local Management screen, use the arrow keys of the
terminal or the workstation providing terminal emulation services. The
Local Management screen cursor responds to the LEFT-ARROW,
RIGHT-ARROW, UP-ARROW, and DOWN-ARROW keys. Each time
you press an arrow key, the Local Management screen cursor moves to
the next available field in the direction of the arrow key.
The Local Management screen cursor only moves to fields which can be
selected or used for input. This means that the cursor jumps over display
fields and empty lines on the Local Management screen.
The Local Management screen cursor provides wrap-around operation.
This means that a cursor located at the edge of a screen, when moved in
the direction of that edge, “wraps around” to the outermost selectable
item on the opposite side of the screen which is on the same line or
column.
[ – ] This key decreases values from some
Local Management selection fields.
For example, “Press [ – ]” means to
press the MINUS key.
DEL The DEL (Delete) key removes
characters from a Local Management
Selection field. For example, “Press
DEL” means to press the DELETE
key.
Table 1-2 Keyboard Conventions (Continued)

Chapter 1: Introduction
Page 1-8 MicroMMAC Local Management User’s Guide
1.8 DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
1.9 RELATED DOCUMENTS
Use the following manuals to supplement the procedures and other
technical data provided in this manual. The procedures contained in the
following manuals are referenced where appropriate, but not repeated in
this manual.
• CabletronSystems
MicroMMAC 10BASE-TIntelligent Stackable Hub
Installation Guide
• Cabletron Systems BRIM User's Guides
1.10 GETTING HELP
If you need additional support related to Local Management, or if you
have any questions, comments, or suggestions concerning this manual,
contact Cabletron Systems Technical Support:
By phone [phone]
Monday – Friday; 8
A . M . – 8 P . M . Eastern Time
By CompuServe GO CTRON from any ! prompt
By Internet mail [email protected]
By FTP ctron.com (134.141.197.25)
Login
anonymous
Password your email address
NOTE
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
TIP
Tip symbol. Conveys helpful hints concerning procedures or
actions.
!
CAUTION
Caution symbol. Contains information essential to avoid
damage to the equipment or poor network performance.

Getting Help
MicroMMAC Local Management User’s Guide Page 1-9
Before calling Cabletron Systems Technical Support, have the following
information ready:
• A description of the failure
• A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
• A description of your network environment (layout, cable type, etc.)
• Network load and frame size at the time of trouble (if known)
• The serial and revision numbers of all Cabletron Systems products in
the network
• The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
• Any previous Return Material Authorization (RMA) numbers

Chapter 1: Introduction
Page 1-10 MicroMMAC Local Management User’s Guide