Cabletron Systems 9F426-03 Technical document

9032058-01
SmartSwitch 9000
9F426-03
Local Management Appendix

1
Appendix
9F426-03 Module Specific
Information
Introduction
This appendix contains local management information that is specific to the
9F426-03 FDDI Switch Module.
Module Interfaces
The 9F426-03 FDDI Switch Module has 8 interfaces. Table 1 lists the identifying
number, name, and description of each interface.
Table 1. 9F426-03 FDDI Switch Module Interfaces
Interface
Number
Interface
Name
Interface
Description
1 SMB1 1 Mbps System Management Bus
2 SMB10 10 Mbps System Management Bus
3 HOST i960 Host
4 CONTROL i960 Data Controller
5 INB Internal Network Bus
6 FRONT1 FDDI Front Panel Port 1
7 FRONT2 FDDI Front Panel Port 2
8 FRONT3 FDDI Front Panel Port 3

9F426-03 Module Specific Information
2
Use the numbers listed in Table 1 to configure the module’s default interface (see
General Configuration Screen in the SmartSwitch 9000 Module Local Management
User’s Guide ).

3
9F426-03 Module Specific Information
Ring Map Configuration Screen
The Ring Map Configuration Screen (Figure 1), contains configuration and
connection information and displays the topology of the FDDI rings connected to
the module.
Figure 1. Ring Map Configuration Screen
SmartSwitch 9000 Local Management
Ring Map Configuration
Module Name: 9F426-03 Firmware Revision: 01.04.10
Slot Number: 11 BOOTPROM Revision: 01.02.00
FDDI Address: 00:00:B8:00:10:62 MAC Count: 1
Current RingMap: FRONT PANEL 1 (isolated) Address Mode: [MAC]
00:00:B8:00:10:62 (NAS) <<<<<<<<<<<<<<<<<<< SMT-Unknown-Address
[FRONT PANEL 1 (isolated)] EXIT RETURN

9F426-03 Module Specific Information
4
Ring Map Configuration Screen Fields
The following information briefly explains each Ring Map Configuration Screen
field.
FDDI Address
Displays the address of the module. The format of this address (either MAC or
Canonical) is determined by the value you select in the Address Mode field.
MAC Count
Displays the number of MACs (Media Access Controllers) that are attached to the
specified ring.
Current Ring Map
Identifies the ring on which a MAC for the specified module resides, and whether
that MAC is located on the primary or secondary path of that ring.
Address Mode (Toggle)
Allows you to select the format in which addresses appear on this screen. Press
the Space Bar to toggle to the desired value. The Address Mode possibilities are:
• MAC
• Canonical
FRONT PANEL x (Toggle)
Allows you to display information about the module’s front panel ports.
Choosing a Front Panel Port
To choose a front panel port:
1. Use the arrow keys to highlight the FRONT PANEL x field (lower left corner
of screen).
2. Press the Space Bar to toggle to the desired port.
3. Press the Return key.

5
9F426-03 Module Specific Information
The Ring Map
The Ring Map shows a series of addresses in upstream/downstream order. These
addresses, which represent each FDDI device attached to the ring, are arranged
on the screen to simulate the circular fashion of a ring. When first displayed, the
station at the upper left corner of this map is your current station. The screen
displays node class, node address, and twisted and/or wrapped conditions (T for
twisted, W for wrapped). The node class possibilities are:
• NAS (Null Attached Station) - Isolated station; station not connected to an
FDDI ring.
• DAS (Dual Attached Station) - Station that does not support M ports, but
connects directly to an FDDI primary and secondary ring using A and B ports.
• DAC (Dual Attached Concentrator) - Station that supports M ports and
connects directly to an FDDI primary and secondary ring using A and B ports.
• SAS (Single Attached Station) - Station that accesses the main ring through a
concentrator, creating a ring of trees topology.
• SAC (Single Attached Concentrator) - Station that accesses the main ring
through another concentrator and, in turn, allows the connection of more
devices. SACs provide the same connections as DACs, without attaching to the
dual ring.
• NAC (Null Attached Concentrator) - Isolated concentrator; concentrator not
connected to an FDDI ring.
While the map is updated, for example, during a ring topology change, the screen
may show ??:??:??:??:??:?? to illustrate an undetermined address.
Displaying the Ring Map Node Screen
To display the Ring Map Node Screen (from the Ring Map Configuration Screen),
use the arrow keys to highlight an address, then press the Return key. The Ring
Map Node Screen appears.
The Ring Map display stops at the first occurrence of an undetermined address,
and does not display any known information beyond this point.
NOTE

9F426-03 Module Specific Information
6
Ring Map Node Screen
The Ring Map Node Screen (Figure 2), displays specific information for a selected
FDDI node on the Ring Map.
Figure 2. Ring Map Node Screen
SmartSwitch 9000 Local Management
Ring Map Node
Module Name: 9F426-03 Firmware Revision: 01.04.10
Slot Number: 11 BOOTPROM Revision: 01.02.00
SELECTED NODE
Address: 00:00:B8:00:10:62
Upstream Address: NO UPSTREAM ADDRESS
Node Class: NAS
Mac Count: 0
Non-Master Count: 0
Master Count: 0
Peer Wrap: No
Unattached Conc: No
Twisted A-A: No
Twisted B-B: No
Synchronous Service: No
Rooted: No
EXIT RETURN

7
9F426-03 Module Specific Information
Ring Map Node Screen Fields
The following information briefly explains each Ring Map Node Screen field.
Address
Displays the address of the selected node.
Upstream Address
Displays the address of the selected node’s nearest upstream neighbor.
Node Class
Displays the class (NAS, DAS, DAC, SAS, or SAC) of the selected node. For an
explanation of these class codes, see page 5.
MAC Count
Displays the number of MACs (Media Access Controllers) that are attached to the
specified ring.
Non-Master Count
Displays the number of A and B ports on the selected node.
Master Count
Displays the number of M ports controlled by the selected node.
Peer Wrap
Indicates whether a wrap condition exists on a port. A peer wrap does not occur
when the A or B port is attached to an M port.
Unattached Conc (DAC only)
Indicates whether the selected node has no active A or B port.
Twisted A-A
Indicates whether the A port is connected to another A port.
Twisted B-B
Indicates whether the B port is connected to another B port.
Synchronous Service
Indicates whether the selected node uses synchronous bandwidth which
guarantees a certain percentage of the total FDDI bandwidth for real-time
applications.
Rooted
Indicates whether the selected node has an active A or B port when one, and only
one, end of the fiber link connects to an M port.

9F426-03 Module Specific Information
8
Switch Configuration Screen
The Switch Configuration Screen (Figure 3), displays parameters you can
configure to make the switch operational.
Figure 3. Switch Configuration Screen
SmartSwitch 9000 Local Management
Switch Configuration
Module Name: 9F426-03 Firmware Revision: 01.04.10
Slot Number: 9 BOOTPROM Revision: 01.02.00
Switch Address: 00-00-1D-00-08-45 Type of STA: [NONE]
Numbers of Ports: 4
Port # MAC Address State Status
1 00-00-1D-00-08-45 disabled [DISABLED]
2 00-00-1D-00-08-46 forwarding [ENABLED]
3 00-00-1D-00-08-47 forwarding [ENABLED]
4 00-00-1D-00-08-48 forwarding [ENABLED]
SAVE EXIT RETURN
Port # refers to the following:
• Port 1 - INB
• Port 2 - Front Panel Port 1
• Port 3 - Front Panel Port 2
NOTE