Cadel INDIGO User manual

USER MANUAL
Pellet Stove
EN
©2019 CADEL srl | All rights reserved - Tutti i diritti riservati
INDIGO - VERA - ELANE - MADISON - TABLA -
ROXY - ATRIUM - SOLO 5

89CD220002EN
CADEL SRL - Via Foresto Sud, 7 - 31025 Santa Lucia di Piave (TV) - ITALY - Tel. [phone] - Fax [phone] - [email protected]om - www.cadelsrl.com
Iscr. registro imprese / Partiva Iva IT 03202180265 - R.E.A.TV 227665 - Capitale Sociale i.v. € 30.000,00
TECHNICAL DOCUMENTATION FOR LOCAL SPACE HEATERS ACCORDINGTO COMMISSION
REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE)
Manufacturer CADEL srl - Via Foresto Sud 7 - 31025 Santa Lucia di Piave (TV) - Italy
Trademak: model identier
CADEL: SPIRIT3 5kW
FREEPOINT: ATRIUM 5 AIRTIGHT
PEGASO: SOLO 5 - MADISON 5
Description Pellet stove
Indirect heating functionality No
Direct heat output 5,2 kW
Indirect heat output - kW
CPR harmonised standard EN 14785
Notied body IMQ Spa (N.B.0051)
Preferred fuel (unique) Compressed wood with moisture content < 12 % YES Wood logs with moisture content ≤ 25 % NO
Other woody biomass NO
ηs85 %
EEI 125 -
Energy Eciency Class (A++ to G scale) A+
Space heating emissions at nominal heat output
PM (al 13% O2)17 mg/Nm3
OGC (al 13% O2)4mg/Nm3
CO (al 13% O2)141 mg/Nm3
NOx(al 13% O2)123 mg/Nm3
Space heating emissions at minimum heat output
Only required if correction factors F(2) or F(3) are applied
PM (al 13% O2)20 mg/Nm3
OGC (al 13% O2)7mg/Nm3
CO (al 13% O2)235 mg/Nm3
NOx(al 13% O2)121 mg/Nm3
Heat output Nominal heat output (Pnom)5,2 kW
Minimum heat output (indicative) (Pmin)2,5 kW
Useful eciency (NCV as received) Useful eciency at nominal heat output (ηth,nom)89,5 %
Useful eciency at minimum heat output (indicative) (ηth,min)91,5 %
Auxiliary electricity consumption At nominal heat output (elmax)0,062 kW
At minimum heat output (elmin)0,015 kW
In standby mode (elsb)0,002 kW
Type of heat output/room temperature control (select one)
Single stage heat output, no room temperature control NO
Two or more manual stages, no room temperature control NO
With mechanic thermostat room temperature control NO
With electronic room temperature control NO
With electronic room temperature control plus day timer NO
With electronic room temperature control plus week timer YES
Other control options (multiple selections possible) Room temperature control, with presence detection NO Room temperature control, with open window detection NO
With distance control option NO
Permanent pilot ame power requirement Pilot ame power requirement (if applicable) (Ppilot)N.A. kW
Observe the specic precautions for installation, assembly and maintenance indicated in the manual accompanying the product.
Issue date: 01.12.2021

89CD220013EN
CADEL SRL - Via Foresto Sud, 7 - 31025 Santa Lucia di Piave (TV) - ITALY - Tel. [phone] - Fax [phone] - [email protected]om - www.cadelsrl.com
Iscr. registro imprese / Partiva Iva IT 03202180265 - R.E.A.TV 227665 - Capitale Sociale i.v. € 30.000,00
TECHNICAL DOCUMENTATION FOR LOCAL SPACE HEATERS ACCORDINGTO COMMISSION
REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE)
Manufacturer CADEL srl - Via Foresto Sud 7 - 31025 Santa Lucia di Piave (TV) - Italy
Trademak: model identier
CADEL: GRACE3
FREEPOINT: ROXY
PEGASO: TABLA
Description Pellet stove
Indirect heating functionality No
Direct heat output 7 kW
Indirect heat output - kW
CPR harmonised standard EN 14785
Notied body IMQ Spa (N.B.0051)
Preferred fuel (unique) Compressed wood with moisture content < 12 % YES Wood logs with moisture content ≤ 25 % NO
Other woody biomass NO
ηs85 %
EEI 126 -
Energy Eciency Class (A++ to G scale) A+
Space heating emissions at nominal heat output
PM (al 13% O2)14 mg/Nm3
OGC (al 13% O2)4mg/Nm3
CO (al 13% O2)129 mg/Nm3
NOx(al 13% O2)116 mg/Nm3
Space heating emissions at minimum heat output
Only required if correction factors F(2) or F(3) are applied
PM (al 13% O2)19 mg/Nm3
OGC (al 13% O2)7mg/Nm3
CO (al 13% O2)183 mg/Nm3
NOx(al 13% O2)103 mg/Nm3
Heat output Nominal heat output (Pnom)7kW
Minimum heat output (indicative) (Pmin)2,7 kW
Useful eciency (NCV as received) Useful eciency at nominal heat output (ηth,nom)89,5 %
Useful eciency at minimum heat output (indicative) (ηth,min)93 %
Auxiliary electricity consumption At nominal heat output (elmax)0,072 kW
At minimum heat output (elmin)0,019 kW
In standby mode (elsb)0,002 kW
Type of heat output/room temperature control (select one)
Single stage heat output, no room temperature control NO
Two or more manual stages, no room temperature control NO
With mechanic thermostat room temperature control NO
With electronic room temperature control NO
With electronic room temperature control plus day timer NO
With electronic room temperature control plus week timer YES
Other control options (multiple selections possible) Room temperature control, with presence detection NO Room temperature control, with open window detection NO
With distance control option NO
Permanent pilot ame power requirement Pilot ame power requirement (if applicable) (Ppilot)N.A. kW
Observe the specic precautions for installation, assembly and maintenance indicated in the manual accompanying the product.
Issue date: 15.12.2021

89CD220009EN
CADEL SRL - Via Foresto Sud, 7 - 31025 Santa Lucia di Piave (TV) - ITALY - Tel. [phone] - Fax [phone] - [email protected]om - www.cadelsrl.com
Iscr. registro imprese / Partiva Iva IT 03202180265 - R.E.A.TV 227665 - Capitale Sociale i.v. € 30.000,00
TECHNICAL DOCUMENTATION FOR LOCAL SPACE HEATERS ACCORDINGTO COMMISSION
REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE)
Manufacturer CADEL srl - Via Foresto Sud 7 - 31025 Santa Lucia di Piave (TV) - Italy
Trademak: model identier
CADEL: SWEET3 7.0 - PERLA3 7.0 - CRISTAL 7.0
FREEPOINT: ONE AIRTIGHT - BEAM AIRTIGHT - ACCENT AIRTIGHT - ACCENT K AIR-
TIGHT- INDIGO EVO 7
PEGASO:VERA 7.0 - LORD7.0
Description Pellet stove
Indirect heating functionality No
Direct heat output 7 kW
Indirect heat output - kW
CPR harmonised standard EN 14785
Notied body IMQ Spa (N.B.0051)
Preferred fuel (unique) Compressed wood with moisture content < 12 % YES Wood logs with moisture content ≤ 25 % NO
Other woody biomass NO
ηs86 %
EEI 126 -
Energy Eciency Class (A++ to G scale) A+
Space heating emissions at nominal heat output
PM (al 13% O2)15 mg/Nm3
OGC (al 13% O2)1mg/Nm3
CO (al 13% O2)42 mg/Nm3
NOx(al 13% O2)117 mg/Nm3
Space heating emissions at minimum heat output
Only required if correction factors F(2) or F(3) are applied
PM (al 13% O2)20 mg/Nm3
OGC (al 13% O2)4mg/Nm3
CO (al 13% O2)238 mg/Nm3
NOx(al 13% O2)140 mg/Nm3
Heat output Nominal heat output (Pnom)7kW
Minimum heat output (indicative) (Pmin)2,5 kW
Useful eciency (NCV as received) Useful eciency at nominal heat output (ηth,nom)90 %
Useful eciency at minimum heat output (indicative) (ηth,min)91 %
Auxiliary electricity consumption At nominal heat output (elmax)0,049 kW
At minimum heat output (elmin)0,023 kW
In standby mode (elsb)0,002 kW
Type of heat output/room temperature control (select one)
Single stage heat output, no room temperature control NO
Two or more manual stages, no room temperature control NO
With mechanic thermostat room temperature control NO
With electronic room temperature control NO
With electronic room temperature control plus day timer NO
With electronic room temperature control plus week timer YES
Other control options (multiple selections possible) Room temperature control, with presence detection NO Room temperature control, with open window detection NO
With distance control option NO
Permanent pilot ame power requirement Pilot ame power requirement (if applicable) (Ppilot)N.A. kW
Observe the specic precautions for installation, assembly and maintenance indicated in the manual accompanying the product.
Issue date: 01.12.2021

CADEL SRL - Via Foresto Sud, 7 - 31025 Santa Lucia di Piave (TV) - ITALY - Tel. [phone] - Fax [phone] - [email protected]om - www.cadelsrl.com
Iscr. registro imprese / Partiva Iva IT 03202180265 - R.E.A.TV 227665 - Capitale Sociale i.v. € 30.000,00
TECHNICAL DOCUMENTATION FOR LOCAL SPACE HEATERS ACCORDINGTO COMMISSION
REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE)
Manufacturer CADEL srl - Via Foresto Sud 7 - 31025 Santa Lucia di Piave (TV) - Italy
Trademak: model identier
CADEL:
FREEPOINT:
PEGASO: ELANE - VENERE AIRTIGHT - TITANIA AIRTIGHT
Description Pellet stove
Indirect heating functionality No
Direct heat output 8,6 kW
Indirect heat output - kW
CPR harmonised standard EN 14785
Notied body KIWA S.p.a.N.0476
Preferred fuel (unique) Compressed wood with moisture content < 12 % YES Wood logs with moisture content ≤ 25 % NO
Other woody biomass NO
ηs85 %
EEI 125 -
Energy Eciency Class (A++ to G scale) A+
Space heating emissions at nominal heat output
PM (al 13% O2)14 mg/Nm3
OGC (al 13% O2)1,5 mg/Nm3
CO (al 13% O2)79 mg/Nm3
NOx(al 13% O2)135,7 mg/Nm3
Space heating emissions at minimum heat output
Only required if correction factors F(2) or F(3) are applied
PM (al 13% O2)19,3 mg/Nm3
OGC (al 13% O2)3,9 mg/Nm3
CO (al 13% O2)274 mg/Nm3
NOx(al 13% O2)104,4 mg/Nm3
Heat output Nominal heat output (Pnom)8,6 kW
Minimum heat output (indicative) (Pmin)2,4 kW
Useful eciency (NCV as received) Useful eciency at nominal heat output (ηth,nom)89,1 %
Useful eciency at minimum heat output (indicative) (ηth,min)92,9 %
Auxiliary electricity consumption At nominal heat output (elmax)0,076 kW
At minimum heat output (elmin)0,012 kW
In standby mode (elsb)0,002 kW
Type of heat output/room temperature control (select one)
Single stage heat output, no room temperature control NO
Two or more manual stages, no room temperature control NO
With mechanic thermostat room temperature control NO
With electronic room temperature control NO
With electronic room temperature control plus day timer NO
With electronic room temperature control plus week timer YES
Other control options (multiple selections possible) Room temperature control, with presence detection NO Room temperature control, with open window detection NO
With distance control option NO
Permanent pilot ame power requirement Pilot ame power requirement (if applicable) (Ppilot)N.A. kW
Observe the specic precautions for installation, assembly and maintenance indicated in the manual accompanying the product.
Issue date: 30.11.2021

DISPOSAL OF MATERIALS
WARNINGS FORTHE CORRECT DISPOSAL OF THE PRODUCT
The owner is the sole party responsible for demolishing and disposing of the product.This must be performed in compliance with
laws related to safety and environmental protection in force in his/her country.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special differentiated waste collection centre set up by the local authorities or to a retailer that provides this
service.
Separating and recycling prevents potential negative effects on the environment and health (often caused by inappropriately
disposing of product parts). It also allows materials to be recovered in order to obtain significant savings in energy and resources.
The following table and the exploded view it refers to highlight the main components that can be found in the device and indica-
tions on how to separate and dispose of them correctly when no longer used.
More specifically, the electric and electronic components must be separated and disposed of in authorised centres, in compliance
with theWEEE directive 2012/19/EU and the relative national transpositions.
Exploded drawing
LEGENDA WHERE TO DISPOSE MATERIALS
A. OUTER CLADDING If there is any, to be disposed of separately based on
the material used:
Metal
Glass
Tiles or ceramics
Stone
B. GLASS DOORS If there is any, to be disposed of separately based on
the material used:
Glass ceramic (fire door): to be disposed of with inert
or mixed waste
Tempered glass (oven door): to be disposed of with
glass
C. INTERIOR CLADDING If there is any, to be disposed of separately based on
the material used:
Metal
Refractory materials
Insulating panels
Vermiculite
Insulation, vermiculite and refractory materials that
have come into contact with flames or exhaust gases
(dispose of in mixed waste)

LEGENDA WHERE TO DISPOSE MATERIALS
D. ELECTRIC AND ELECTRO-
NIC COMPONENTS
To be disposed of separately in authorised centres, as
indicated in theWEEE directive 2012/19/EU and the
relative national transposition.
Wiring, motors, fans, circulators, display panels, sen-
sors ignition plug, electronic cards, batteries.
E. METAL STRUCTURE To be disposed of separately with metal -
F. COMPONENTSTHAT CAN-
NOT BE RECYCLED To be disposed of with mixed waste E.G.: Gaskets, rube piping, silicone or fibres, plastic.
G. HYDRAULIC COMPONENTS Piping, fittings, expansion vessel, valves. If there are any, to be disposed of separately based on the mate-
rial they are made of:
Copper
Brass
Stainless steel
Other materials
INSTRUCTIONS FOR PACKAGING DISPOSAL
The material that the appliance’s packaging is made of must be managed correctly, in order to make collection, reuse, recovery
and recycling easier, where possible.
The table below illustrates the possible components that the packaging is made of, and the relative instructions for correct dispo-
sal.
DESCRIPTION CODE MATERIAL SYMBOL DIRECTIONS FOR COLLECTION
-WOOD BED
-WOOD CAGE
-WOOD PALLET
WOOD
FOR 50
SORTED waste collection
WOOD
Check with the competent body on
how to dispose of this packaging at
the recycling depot
- CARDBOARD BOX
- CARDBOARD CORNER
- CARDBOARD SHEET
CORRUGATED CARDBOARD
PAP 20
SORTED waste collection
PAPER
Check the instructions of the compe-
tent body
- APPLIANCE BAG
- BAG OF ACCESSORIES
- BUBBLEWRAP
- PROTECTIVE SHEET
- LABELS
POLYETHYLENE
LD PE 04
SORTED waste collection
PLASTIC
Check the instructions of the compe-
tent body
- POLYSTYRENE
- FOAM PEANUTS POLYSTYRENE PS 6
SORTED waste collection
PLASTIC
Check the instructions of the compe-
tent body
- STRAP
-TAPE POLYPROPYLENE PP 5
SORTED waste collection
PLASTIC
Check the instructions of the compe-
tent body.
- SCREWS
- STAPLES FOR STRAP
- FASTENING BRACKET
IRON
FE 40
SORTED waste collection
METAL
Check with the competent body on
how to dispose of this packaging at
the recycling depot

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
2
SUMMARY
1 MANUAL SIMBOLOGY....................................3
2 DEAR CUSTOMER..........................................3
3 CAUTIONS....................................................3
4 SAFETY REQUIREMENTS ...........................4
5 WARRANTY CONDITIONS...............................5
6 SPARE PARTS ...............................................6
7 WARNINGS FOR THE CORRECT DISPOSAL OF THE
PRODUCT ...........................................................6
7.1 INFORMATION FOR MANAGEMENT OF ELECTRIC AND
ELECTRONIC APPLIANCEWASTE CONTAINING BATTERIES OR
ACCUMULATORS ................................................................6
8 WIFI CONNECTION  BLUETOOTH.................7
8.1 NAVEL STAND ALONE..............................................7
9 USE .............................................................8
9.1 INTRODUCTION.......................................................8
9.2 CONTROL PANEL .....................................................9
9.3 USER MENU...........................................................11
9.3.1 MENU M1  CLOCK SETTING................................15
9.3.2 MENU M2  CHRONO SETTING............................15
9.3.3 MENU M3  LANGUAGE SELECTION....................18
9.3.4 MENU M4  STANDBY........................................18
9.3.5 MENU M5  BUZZER............................................19
9.3.6 MENU M6  FIRST LOAD......................................19
9.3.7 MENU M7  STOVE STATUS..................................19
9.3.8 MENU M8  ENGINEER SETTINGS........................19
9.3.9 MENU M9  PELLETTYPE....................................20
9.3.10 MENU MA  FLUE TYPE........................................20
9.3.11 MENU MB  EXIT .................................................20
9.4 STOVE SWITCHON................................................20
9.5 FAILED IGNITION...................................................21
9.6 POWER FAILURE....................................................21
9.7 TEMPERATURE SETTING........................................21
9.8 POWER SETTING ...................................................21
9.9 SWITCHING OFF ....................................................22
9.10 CONNECTION TOTHE EXTERNALTHERMOSTAT.....22
10 FUEL..........................................................22
10.1 FUEL......................................................................22
10.2 PELLET SUPPLY .....................................................23
10.3 PELLET REFUELLING TIMER...................................23
10.4 VENTILATION ........................................................23
10.5 REMOTE CONTROL OPTIONAL ............................24
11 SAFETY DEVICES AND ALARMS ....................25
11.1 SAFETY DEVICES ...................................................25
11.2 PRESSURE SWITCH................................................25
11.3 SMOKE TEMPERATURE PROBE..............................25
11.4 CONTACT THERMOSTAT INTHE FUEL HOPPER.......25
11.5 ELECTRICAL SAFETY..............................................25
11.6 SMOKE FAN ...........................................................25
11.7 GEAR MOTOR.........................................................25
11.8 TEMPORARY POWER CUT......................................25
11.9 FAILED STARTUP..................................................25
11.10 BLACKOUTWITHTHE BOILER ON..........................25
11.11 FLUE GASTEMPERATURE PROBE ALARM..............26
11.12 FLUE GAS OVERTEMPERATURE ALARM.................26
11.13 FAULTY FLUE GAS ENCODER ALARM.....................26
11.14 FAILED IGNITION ALARM ......................................27
11.15 NO PELLET ALARM................................................27
11.16 THERMAL SAFETY OVERHEATING ALARM ............27
11.17 NO NEGATIVE PRESSURE ALARM..........................27
11.18 ALARM ALERTS .....................................................28
11.19 ALARM RESET .......................................................30
12 ROUTINE MAINTENANCE.............................30
12.1 INTRODUCTION.....................................................30
12.2 DAILY OR WEEKLY CLEANING PERFORMED BY THE
USER 31
12.3 BEFORE EACH STARTUP.......................................31
12.4 HOPPER AND AUGER CLEANING ...........................31
12.5 FUME PIPES ANNUAL CLEANING .........................32
12.6 GENERAL CLEANING..............................................32
12.7 CLEANING OF PAINTED METAL PANELS ................32
12.8 GLASS CLEANING ..................................................32
13 IN CASE OF ANOMALY..................................32
13.1 PROBLEM SOLVING...............................................32

3
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
1 MANUAL SIMBOLOGY
USER
AUTHORISED TECHNICIAN
(ONLY to interpret or the Stove-manufacturer or the Authorized Techni-
cian of Technical Assistance Service approved by the Stove-manufacturer)
SPECIALIZED STOVE-REPAIRER
CAUTION:
READ CAREFULLY THE NOTE
CAUTION:
DANGER OR IRREVERSIBLE DAMAGE POSSIBILITY
• The icons with the stylized figures indicates whom the subject dealt in the paragraph is addressed to (between the User and/
or the AuthorizedTechnician and/or the Specialized Stove-repairer).
• WARNING symbols indicates an important note.
2 DEAR CUSTOMER
• Our products are designed and manufactured in compliance with European regulations harmonised with Regulation (EU) no.
305/2011 for construction products (EN13240 for wood-burning stoves, EN14785 for pellet-burning appliances, EN13229 for
fireplaces/wood-burninginserts andEN 12815for wood-burning range cookers),with highqualitymaterialsand extensiveex-
perience in transformation processes.The products also comply with the essential requirements of Directive 2009/125/EC (Eco
Design) and, where applicable, Directives 2014/35/EU (LowVoltage), 2014/30/EU (Electromagnetic Compatibility), 2014/53/
EU (Radio Frequency), 2011/65/EU (ROhS).
• Read carefully the instruction contained in this manual to obtain the best efficiency.
• This instruction manual is an integral part of the product: make sure it is delivered with the appliance also in case of sold to
others. In case of loss please ask a copy to your localTechnical Assistance Service.
In Italy biomass system installation below 35 kW must comply with MD 37/08. Every qualified installer who
own these requirements, has to issue the certificate of conformity for the installed system ("system" means:
stove + chimney + air inlet).
• According to (EU) No. 305/2011 regulation, the " Declaration of Performance" and “Declaration of Conformity” are available
online at the web sites:
- www.cadelsrl.com
- www.free-point.it
- www.pegasoheating.com
3 CAUTIONS
• Allthe picturescarried in thismanualareonly forindicativeandexplanatorypurposeand could thereforeslightly differfromyourappliance.
• The referring appliance is those you purchased.
• In case of doubts or difficulties in the comprehension or for problems not described in this manual, please promptly contact
your distributor or installer.

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
4
4 SAFETY REQUIREMENTS
• Installation, electrical connection, functional verification and maintenance must only be
performed by qualified or authorised personnel.
• Live electrical parts: disconnect the product from the 230V power supply before perfor-
ming any maintenance operation. Only power the product after completing assembly.
• Special maintenance must only be performed by authorised and qualified personnel.
• All local regulations, including those referring to national European standards, must be
respected during appliance installation.
• The manufacturer declines any responsibility in case of installation which are not in com-
pliance with current regulations, in case of a wrong room ventilation system, in case of an
electric connection which is not in compliance with regulations and in case of a wrong use of
the appliance.
• It is forbidden to install the stove in bedrooms, bathrooms and in rooms used for storing
combustible materials and in one-room flats.
• The installation in one-room flats is allowed if they are in sealed chamber.
• In any case the stove must not be installed in rooms where it can get in touch with water or
water splashes because this can cause burn hazards and short-circuit.
• Please check that the floor has an adequate load capacity. If the existing one does not
satisfy this requirement, appropriate measure should be provided (for example a plate for di-
stributing the load).
• For safety fire regulations the distances from flammable or sensible to heat objects (sofas,
pieces of furniture, wooden covering, etc...) must be respected.
• If there are highly flammable objects (curtains, fitted carpet, etc...), all these distances
must be further increased with 1 meter.
• If the floor is made of combustible material, we recommend using a protector made of in-
combustible material (steel, glass, etc.) that also protects the front part from any falling burnt
particles during cleaning.
• The electrical cable must not get in touch with the fume exhaust pipe and nor with every
other part of the stove.
• The user, or whoever is operating the product, must read and fully understand the contents
of this installation and use guide before performing any operation. Errors or incorrect settings
can cause hazardous conditions and/or poor operation.
• The type of fuel to use is only the pellets.
• Do not use the appliance as waste inceneretor.
• Do not place laundry on the product to dry. Any clothes horses or similar objects must be
kept at a safe distance from the product. Fire hazard.
• It is forbidden to operate the product with the door open or the glass broken.
• It is forbidden to modify the appliance without authorization.
• Do not use flammable liquids during the ignition (alcool, petrol, oil, etc...).
• After a failed ignition the burning pot must be empty from the amassed pellets, before
starting the stove up again.
• The pellet hopper must always be closed with its own lid.
• Before of every intervention leave the fire completely extinguish till the cooling and always
disconnect the plug from the electric socket.
• This appliance can be used by children aged from 8 years and above and persons with re-
duced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Packaging are not toys and could cause suffocation or strangulation and other health ha-
zards! People (childreen included) with reduced mobility, psycological deseases or without

5
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
experience and knowledge must be kept away from packaging.The stove is not a toy.
• Childreen must be constantly overseen in order to assure that they do not play with the
appliance.
• During its running, the stove reaches high temperatures: keep away childreen and animals
and for your safety please use appropriate fireproof devices, such as heat-protecting gloves.
• The stove is equipped with a safety device that stops the feed screw immediately when the
pellet loading door is opened.This safety device (standard EN 60335-2-102) prevents the user
from coming into contact with the moving parts of the appliance.
• The chimney flue must be cleaned, since the soot and unburnt oil deposits reduce its sec-
tion so blocking the draught. In great quantities they can flare up.
• If the pellets are of bad quality (if contains sizing agents, oils, varnishes, plastic remains or
if it is mealy), deposits will form along pellets drop pipe during the running. When the stove is
switched off, these remains could form little hot coals that rising along the pipe could reach the
pellets on the hopper burning them and creating a thick and harmful smoke inside the room.
Please always keep the hopper closed with its own lid. If the pipe is sooty, please clean it.
• In case it would be necessary to extinguish the fire emitted by the stove or by the chimney
flue, use a fire-extinguisher or contact the firemen. Do not use water to extinguish the fire
inside the burning pot.
5 WARRANTY CONDITIONS
The company guarantees the product, with the exception of elements subject to normal wear listed below, for a period of
2 (two) years from the date of purchase attested by:
• a document to serve as proof of purchase (invoice and/or receipt) that shows the name of the vendor and the date on which
the purchase was made;
• forwarding of the completed certificate of guarantee within 8 days of purchase.
Furthermore, the product must be installed and started by specialised personnel who must, where provided, issue a declaration of
conformity of the plant and of the proper functioning of the product, for the warranty to be valid and effective.
We recommend testing the product before completion with the relative finishes (claddings, painting of walls, etc.).
Installations not meeting the current standards, improper use and lack of maintenance as expected by the manufacturer, void the
product warranty.
The guarantee is valid on the condition that the instructions and warnings contained in the use and maintenance manual are
observed, and therefore the product is used correctly.
The replacement of the entire system or the repair of one of its components does not extend the guarantee period, and the original
expiry date remains unchanged.
The guarantee covers the replacement or free repair of parts recognised as being faulty at source due to manufacturing
defects.
To benefit from the guarantee, in the event of a fault, the customer must have the guarantee certificate and present it with the
proof of purchase document to theTechnical Assistance Office.
The guarantee does not cover malfunctions and/or damage to the appliance that arise due to the following causes:
• Damage caused during transportation or relocation.
• All parts that develop faults due to negligence or improper use, incorrect maintenance, installation that does not comply with
the manufacturer's instructions (always refer to the installation and use manual provided with the appliance).
• Incorrect dimensioning with regards to the use or faults in the installation or failure to adopt the necessary devices to guaran-
tee proper execution.
• Improper overheating of the equipment, use of fuels not conforming to the types and quantities indicated in the instructions
provided.
• Further damage caused by incorrect user interventions in an attempt to fix the initial fault.
• Worsening of the damage due to the continued use of the equipment by the user, once the defect has been noticed.
• In the presence of a boiler, any corrosions, incrustations or breaks caused by water flow, condensation, hardness or acidity of
the water, improperly performed descaling treatments, lack of water, mud or limescale deposits.
• Inefficiency of chimneys, flues or parts of the plant affecting the equipment.
• Damagecaused by tampering withthe appliance,atmosphericagents,naturaldisasters,vandalism,electricaldischarges,fires,

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
6
faults in the electric and/or hydraulic system.
• Failure to have the stove cleaned on an annual basis by an authorised technician or qualified personnel will result in the loss
of the warranty.
Also excluded from this guarantee are:
• Parts subject to normal wear such as gaskets, glass, claddings and cast iron grids, painted, chrome-plated or gilded parts,
handles and electric cables, bulbs, indicator lights, knobs, all parts which can be removed from the hearth.
• Variations in colour of the painted or ceramic/serpentine parts and craquelure ceramics as they are natural characteristics of
the material and product use.
• Masonry work.
• Plant parts (if present) not supplied by the manufacturer.
Any technical interventions on the product to eliminate the above-said defects and consequent damages must be agreed upon
with theTechnical Assistance Centre, who reserves the right to accept the relative appointment or not. However, said interventions
will not be carried out under warranty but as technical assistance to be granted at part of any eventual and specific agreed condi-
tions and in accordance with the fee in force for the work to be carried out.
The user will also be charged for any costs incurred to remedy the incorrect technical interventions, tampering or damage to the
appliance, not attributable to original faults.
Save for the legal or regulatory limits, the guarantee does not cover the containment of atmospheric and acoustic pollution.
The company declines all liability for any damage which may be caused, directly or indirectly, to persons, animals
or objects as a consequence of non compliance with any prescription specified in the manual, especially warnings
regarding installation, use and maintenance of the appliance.
6 SPARE PARTS
For each repair or adjustment which should be necessary, please contact the dealer where you purchased your stove or your nea-
restTechnical Assistance Service, specifying:
• Appliance model
• Serial number
• Type of problem
Use only original spare parts which you can find at ourTechnical Assistance Services.
7 WARNINGS FOR THE CORRECT DISPOSAL OF THE PRODUCT
The owner is the sole party responsible for demolishing and disposing of the product.This must be performed in compliance with
laws related to safety and environmental protection in force in his/her country.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special differentiated waste collection centre set up by the local authorities or to a retailer that provides this
service.
Separating and recycling prevents potential negative effects on the environment and health (often caused by inappropriately
disposing of product parts). It also allows materials to be recovered in order to obtain significant savings in energy and resources.
7.1 INFORMATION FOR MANAGEMENT OF ELECTRIC AND ELECTRONIC APPLIANCE WASTE CON

7
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
TAINING BATTERIES OR ACCUMULATORS
Fig. 1 - Waste disposal
This symbol, which is used on the product, batteries, accumulators or on the packaging or documents, means that at the end of its
useful life, this product, the batteries and the accumulators included must not be collected, recycled or disposed of together with
domestic waste.
Improper management of electric or electronic waste or batteries or accumulators can lead to the leakage of hazardous substances
contained in the product. For the purpose of preventing damage to health or the environment, users are kindly asked to separate
this equipment and/or batteries or accumulators included from other types of waste and to arrange for disposal by the municipal
waste service It is possible to ask your local dealer to collect the waste electric or electronic appliance under the conditions and
following the methods provided by national laws transposing the Directive 2012/19/EU.
Separate waste collection and recycling of unused electric and electronic equipment, batteries and accumulators helps to save
natural resources and to guarantee that this waste is processed in a manner that is safe for health and the environment.
For more information about how to collect electric and electronic equipment and appliances, batteries and accumulators, please
contact your local Council or Public Authority competent to issue the relevant permits.
8 WIFI CONNECTION  BLUETOOTH
8.1 NAVEL STAND ALONE
Procedure if only valid for models with NAVEL STAND ALONE Wi-Fi technology.
ATTENTION! Installation must ONLY be carried out by specialised personnel.
The manufacturer will not be held responsible for injury to persons or damage to property or in the event of
failed operation.
The Wi-Fi module uses the domestic Wi-Fi network; ensure there is enough coverage in the
place of installation.

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
8
Fig. 2 - NAVEL STAND ALONE module Fig. 3 - App EASY CONNECT PLUS
The documentation for connecting theWi-Fi and using the App are available online at the following addresses:
https://www.cadelsrl.com/donwload-wi-fi/
http://www.free-point.it/it/downloads/
https://www.pegasoheating.com/it/documenti/
9 USE
9.1 INTRODUCTION
To have the best performance with the lowest consumption please follow the here descripted instructions.
• The lightning of the pellets occurs very easily if the installation is correct and if the chimney flue is efficient.
• Switch on the stove at Power 1 for at least 2 hours in order to enable the materials which make up the boiler and the fireplace
to adjust the inner springing stress.

9
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
• By using the stove the varnish inside the combustion chamber could be subjected to alterations. This occurrence can be attri-
buted to different reasons: an excessive stove overheating, the presence of chemical agents in bad quality pellets, bad chimney
draught, etc.Therefore varnish endurance in the combustion chamber cannot be guarantee.
Oily plant waste and lacquers can cause smells and smoke during the first working hours: it is advisable to
ventilate the room because they could be noxious to people and animals.
Set values from 1 to 5 are defined by the manufacturer and they can be changed only by an authorized tech-
nician.
9.2 CONTROL PANEL
The display allows you to dialogue with the stove by simply pressing a few buttons. A display with scrolling text and LED indicators
inform the user about the stove's operating status.
Meaning of the buttons (see Fig. 2)
Fig. 4 - Display: 3 buttons
REFERENCE BUTTON DESCRIPTION MODE ACTION
1Decreases temperature
and power
TEMPERATURE SETTING Decreases the value of the ambient temperature
SETTING
PROGRAMMING Decreases the selected
parameter
POWER SETTING Decreases the value of the
operating power
2Increases the temperature
and power
TEMPERATURE SETTING Increases the value of the ambient temperature
SETTING
PROGRAMMING Increases the selected
parameter
POWER SETTING Increases the value of the
operating power

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
10
REFERENCE BUTTON DESCRIPTION MODE ACTION
3ON/OFF
WORK Pressed for 2 seconds, it turns the stove on or off
accordingly
PROGRAMMING Allows you to select the pa-
rameters to be programmed
Meaning of the LEDs that are on (see Fig. 3):
Fig. 5 - Display: LEDs on
REFERENCE SYMBOL DESCRIPTION LED ON
1AMBIENT SETTING Ambient setting programming
2POWER SETTING Power setting programming
3ON/OFF Work status
4CHRONO Chrono is enabled
5ALARM Stove is in alarm

11
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
REFERENCE SYMBOL DESCRIPTION LED ON
6FEED SCREW ON Feed screw moving
7HEAT EXCHANGER Heat exchanger on
8SPARK PLUG Ignition spark plug
9.3 USER MENU
The following table briefly describes the menu structure; this paragraph solely focuses on the selections available to the user.
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
M1 Set orologio
M1-SEt cLocK
01 - Day of the week M-T-W-T-F-S-S Mond-tuES-uEdn-tHur-Frid-
SAtu-Sund
02 - Clock hours
02-tiME cLocK 0-23
03 - Clock minutes
03-MinutES cLocK 0-59
04 - Clock day
04-dAy cLocK 1-31
05 - Clock month
05-MontH cLocK 1-12
06 - Clock year
06-yEAr cLocK 00-99
M2 - Chrono setting
M2-SEt cHrono
M2-1 - Enable chrono
M2-1 cHrono EnAbLE
01 - enable chrono
01-cHrono EnAbLE on/off
M2-2 - Daily programming
M2-2 ProGrAM dAy
01 - daily chrono
01-cHrono dAyLy on/oFF
02 - start 1 day
02-StArt 1 dAyLy oFF-0-23:50

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
12
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
03 - stop 1 day
03-StoP 1 dAyLy oFF-0-23:50
04 - start 2 day
04-StArt 2 dAyLy oFF-0-23:50
05 - stop 2 day
05-StoP 2 dAyLy oFF-0-23:50
M2-3 -Weekly programming
M2-3 -ProGrAM uEEK
01 - week chrono
01-crono uEEKLy on/oFF
02 - start Prg 1
02-StArt PrG1 oFF-0-23:50
03 - stop Prg 1
03-StoP PrG1 oFF-0-23:50
04 - Monday Prg1
04-Mond PrG1 on/oFF
05 -Tuesday Prg 1
05-tuES PrG1 on/oFF
06 -Wednesday Prg 1
06-uEdn PrG1 on/oFF
07 -Thursday Prg1
07-tHur PrG1 on/oFF
08 - Friday Prg 1
08-Frid PrG1 on/oFF
09 - Saturday Prg 1
09-SAtu PrG1 on/oFF
10 - Sunday Prg 1
10-Sund PrG1 on/oFF
11 - start Prg 2
11-StArt PrG2 oFF-0-23:50
12 - stop Prg 2
12-StoP PrG2 oFF-0-23:50
13 - Monday Prg2
13-Mond PrG2 on/oFF
14 -Tuesday Prg 2
14-tuES PrG2 on/oFF
15 -Wednesday Prg 2
15-uEdn PrG2 on/oFF
16 -Thursday Prg2
16-tHur PrG2 on/oFF
17 - Friday Prg 2
17-Frid PrG2 on/oFF

13
INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
18 - Saturday Prg 2
18-SAtu PrG2 on/oFF
19 - Sunday Prg 2
19-Sund PrG2 on/oFF
20 - start Prg 3
20-StArt PrG3 oFF-0-23:50
21 - stop Prg 3
21-StoP PrG3 oFF-0-23:50
22 - Monday Prg3
22-Mond PrG3 on/oFF
23 -Tuesday Prg 3
23-tuES PrG3 on/oFF
24 -Wednesday Prg 3
24-uEdn PrG3 on/oFF
25 -Thursday Prg3
25-tHur PrG3 on/oFF
26 - Friday Prg 3
26-Frid PrG3 on/oFF
27 - Saturday Prg 3
27-SAtu PrG3 on/oFF
28 - Sunday Prg 3
28-Sund PrG3 on/oFF
29 - start Prg 4
29-StArt PrG4 oFF-0-23:50
30 - stop Prg 4
30-StoP PrG4 oFF-0-23:50
31 - Monday Prg4
31-Mond PrG4 on/oFF
32 -Tuesday Prg 4
32-tuES PrG4 on/oFF
33 -Wednesday Prg 4
33-uEdn PrG4 on/oFF
34 -Thursday Prg4
34-tHur PrG4 on/oFF
35 - Friday Prg 4
35-Frid PrG4 on/oFF
36 - Saturday Prg 4
36-SAtu PrG4 on/oFF
37 - Sunday Prg 4
37-Sund PrG4 on/oFF
M2-4 -Weekend program
M2-4-ProGrAM u-End

INDIGO - VERA - ELANE - MADISON - TABLA - ROXY - ATRIUM - SOLO 5
14
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
01 - weekend chrono
01-cHrono uEEK End on/oFF
02 - start weekend 1
02-StArt 1 uEEK End oFF-0-23:50
03 - stop weekend 1
03-StoP 1 uEEK End oFF-0-23:50
04 - start weekend 2
04-StArt 2 uEEK End oFF-0-23:50
05 - stop weekend 2
05-StoP 2 uEEK End oFF-0-23:50
M2-5 - Exit
M2-5-EScAPE set
M3 - Choose language
M3-LAnGuAGE
01 - Italian
01-LinG itA set
02 - English
02-LinG EnG set
03 - French
03-LinG FrE set
04 - German
04-LinG dEu set
05 - Spanish
05-LinG SPA set
06 - Portuguese
06-LinG Por set
M4 - Stand-by
M4-StAnd-by
01 - Stand - by
01-StAnd-by on/oFF
M5 - Buzzer
M5 buCCEr
01 - Buzzer
01-buCCEr on/oFF
M6 - First load
M6 LoAd initiAL
01 - First load
01-LoAd initiAL 90"
M7 - Stove status
M7 StAtE StoVE
01 - Stove status
01-StAtE StoVE