Caffitaly System S06HS User manual

INSTRUCTION MANUAL
Imported by Roasting Australia Holdings Pty Limited
11 Hoyle Avenue, Castle Hill, NSW 2154
Phone: [phone]
E-Mail: [email protected]
MODEL S06HS
ONLY USE WITH
Caffitaly System
Capsules
t
e
s
t
e
d
Safety
EMC

z
• Introduction 2
• Safety Warnings 3
• Symbols Guide 4
Instructions:
• Machine Components 5
• First Time Use 6
• Correct Use Of The Buttons 7
• Dispensing Beverages - Using Factory Settings 8
• Turning On The Appliance 9
• Dispensing Hot Water 9
• Frothing / Dispensing Steam 10
• Programming The Quantity Of Beverage In A Cup 11
• General Operating Indications 13
Cleaning and Maintenance:
• Daily Maintenance 14
• Descaling 15
• Changing the Gasket 18
• Saving Energy 18
Miscellaneous:
• Restore Original Settings (RESET) 19
• Troubleshooting 20
• Technical Data 22
• Instructions for Use and Disposal 22
• Caffitaly System Care Contact 22
INDEX
1.

2.
CONGRATULATIONS
on the purchase of your New Caffitaly System S06HS Machine.
You can now savour your favourite hot beverages at any time, day or
night with the Caffitaly System S06HS by choosing one of the many
compatible Caffitaly System capsules available.
With the added Steam Wand, you can enjoy a cappuccino with lightly
frothed milk, a cocoa-flavoured beverage made with steamed milk;
even a cup of tea at the press of a button! They are all easy to prepare,
mess free and ready in seconds.

z
SAFETY WARNINGS
If you do not comply with the operating instructions and safety warnings in this Instruction
Manual, the machine may become dangerous to operate. Please ensure you keep this
Instruction Manual in a safe place. Carefully read the following instructions before use.
This way you will avoid the risk of personal injury and damage to the appliance.
3.
Continued on next page... >>
• This appliance is intended to be used in domestic environments.
Not suitable for Professional use.
• Use ONLY Caffitaly System compatible capsules. Damage caused by using incorrect
capsules will void the guarantee.
• Use the TEA button (Blue) for Tea ONLY!
Incorrect use of this button will cause damage to the machine and void the guarantee.
• Use of the appliance in any manner other than as directed herein could cause harm to
persons and void the guarantee. The manufacturer will not be responsible for injury or
damage resulting from improper use of the appliance.
• After removing the packaging, check that the appliance is not damaged. If damage is
detected, or upon the first sign of a defect (unusual noise or odours), or if any other
problem is detected inside the appliance, do not use it and contact the Roasting
Australia Customer Service Line on 02 9846 0307.
• The packaging elements (plastic bags, etc.) must not be left within reach of children as
they are potential sources of danger.
• Only use the appliance if the power cord is intact; if the cord is damaged it must be
replaced by the manufacturer or qualified person, due to potential electrical safety risks.
Contact the Roasting Australia Customer Service Line on 02 9846 0307.
• Use and store the appliance indoors. Make sure the electrical elements, plug and cord
are dry. Never submerge the appliance in water. Protect the appliance from sprays and
drips. Water and electricity together constitute a risk of electrocution.
• Do not leave the power cord near hot surfaces, sharp edges or other sharp objects.
• Only connect the appliance to power outlets complying with the requirements of the law.
Make sure that the power supply voltage matches the rating shown on the data plate
on the bottom of the appliance.
• Do not pull on the power cord to disconnect it. Remove the plug carefully to avoid
damage to the outlet.
GUARANTEE
VOID
X
X

• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not
play with the appliance.
• Never place your hands inside the capsule compartment. There is a risk of injury.
• Do not open the lever while the appliance is operating. If the lever is raised during the
delivery of a product, the machine can emit jets of hot water. Risk of Burns!
• Do not remove parts of the appliance, OR insert objects into the openings. This could
cause electric shocks! Any operation that is not described in this instruction manual
should only be performed by an Authorised Support Centre. Please contact the Roasting
Australia Customer Service Line on 02 9846 0307.
• Install the appliance on a solid, stable, heat resistant surface with an incline no greater
than 2 degrees.
• When the Indicator Light blinks ORANGE and the machine emits 3 beeps, please
perform the descaling cycle, as illustrated on Page 15. If you do not, the appliance may
be damaged.
• Clean the appliance carefully and regularly with a soft cloth and a mild detergent, do
not use alkaline cleaning agents. If it is not cleaned, the build-up that forms may be
hazardous to your health. Unplug the appliance and allow it to cool before cleaning.
• Unplug the machine if you do not expect to use the appliance for a long period of time
(leaving on vacation, etc.).
SAFETY WARNINGS - Continued
SYMBOLS GUIDE
CAUTION: This is the safety warning symbol. It
is used to call your attention to possible risks of
personal injury. Abide by the safety messages
provided in order to avoid possible injury or death.
This is the symbol
used to highlight some
actions that will optimise
the use of this appliance.
Not
Dishwasher
Safe
Maintenance
Tips
Barista
Tips
4.

z
Double Espresso
Button
60ml (Lit White)
Single Espresso
Button
30ml (Lit White)
Hot Water/Steam
Control Lever
Indicator Light
Orange=Descale
Red=Check System
TEA Button -120ml
(Lit Blue)
Hot Water/
Steam Control
Lever
Lever for opening
and closing Capsule
Compartment
Dispensing Spout
(adjustable)
Steam Wand for
Frothing / Hot
Water
Special Rubber
Grip
Power Cord
Water Tank
Water Tank
Cover
Used Capsule
Drawer
Capsule
Compartment
Power
On/Off Switch
Drip Tray
MACHINE COMPONENTS
Diagram 1:
Diagram 2:
5.

FIRST TIME USE
Please ensure you only use Caffitaly
System Capsules which can be
identified by the Caffitaly logo.
We recommend following these steps
after not having used the machine for
a long period of time.
Continued on next page... >>
6.
ONLY USE WITH
Caffitaly System
Capsules
Fill the tank with
fresh, still water
(either by filling
through the
water tank cover
or removing
the water tank).
1.
Plug in
appliance.
Switch machine
on using the
On/Off Switch.
2.
ON
Place a large
empty container
(at least 250 ml)
under the coffee
dispensing spout.
5.
Press the Double
Espresso button.
The machine will
draw water through
the system (Approx.
30 sec.). When
done, the indicator
light will switch off.
6.
7.
Once successfully
primed, all the
button lights will
continue to blink
while the machine
is warming up
(Approx. 1 min.).
i
NOTE: If the
buttons and the
indicator light
continue to blink
and no water has
been extracted,
repeat Step 6.
Along with the
button lights,
the indicator
light will also
blink RED.
4.
Make sure the
lever is closed.
*Ensure there
is no capsule in
machine.
3.

z
FIRST TIME USE - Continued
CORRECT USE OF BUTTONS
Single Espresso Button - 30ml
(Lit in WHITE). Used for dispensing a
single espresso shot.
When in doubt follow the
directions on the capsule box
regarding required button use.
Diagram 3:
7.
Double Espresso Button - 60ml
(Lit in WHITE). Use for dispensing
a double espresso coffee for a
stronger beverage. Also suitable for
Hot Chocolate, Chai Latte and similar
beverages (NOT TEA).
WARNING:
During the priming
and rinsing stage,
HOT WATER will
be collected in
the used capsule
drawer. Danger of
scalding.
!
When all the
button lights
remain steadily lit,
rinse by pressing
the Double
Espresso button.
Press again to
repeat cycle.
8.
10.
When all the
button lights are
lit steadily, the
machine is ready
to use. Refer
to “Dispensing
Beverages” on
Page 8.
At the end of this
operation, raise
the lever and
carefully remove
the used capsule
drawer. Empty
the water, rinse
and replace.
9.
Tea Button - 120mL (Lit in BLUE)
should only be used for tea capsules.
Do not use the Tea Button for
espresso coffee or any other
beverages except tea! When operating
in this mode, the machine is set for low
pressure, this reduces the ‘crema’ and
diminishes the flavour of the coffee. May
also cause a break in the flow.
Capsules appropriate for the Tea button will be indicated
on the packaging. Inappropriate use of this button may
damage the machine and void your warranty.

DISPENSING BEVERAGES - Using Factory Settings
MAINTENANCE TIP: Traces of the product just dispensed may remain in the
circuit of the machine. Between uses, to ensure optimum product delivery, remove
used capsule from machine and rinse by pressing Double Espresso button.
NOTE: The quantity of beverage dispensed can be programmed according to
personal taste and the size of the cups or mugs used. Please refer to chapter
“Programming the quantity of beverage in a cup” on Page 11.
8.
Plug in appliance.
Switch machine
on using the On/
Off Switch.
ON
1.
Raise the lever to
open the capsule
compartment.
2.
Insert the
capsule, pressing
it gently into
place.
3.
Close the lever
fully and place
a cup or mug
under the coffee
dispensing spout.
4.
Press and release
the button
corresponding
to the type of
beverage you want
as per Diagram 3
on Page 7.
5. 6.
The selected
beverage button
will blink and
machine will stop
dispensing on
reaching the
programmed
quantity.
Gently raise the
lever to eject the
used capsule
into the drawer
and then close
the lever.
7.
WARNING:
There may be
some residual HOT
WATER within
the capsule area.
Stand to the side of
the machine when
opening the lever.
!

z
TURNING ON THE APPLIANCE - DAILY USE
DISPENSING HOT WATER
To stop dispensing
the hot water,
return the control
lever to its central
position. Remove
the container of
hot water.
Place a metal
container or
cup under the
steam wand
dispensing pipe.
1.
Remember to
clean the tube
with a damp
cloth after each
use. WARNING:
Steam wand
tube will be hot.
4.
9.
Fill the water tank
with fresh, still
water (either by
filling through the
water tank cover
or removing
the water tank).
1.
Switch machine
on using the
On/Off Switch.
ON
4.
When all the
button lights are
lit steadily, your
machine is ready
to use.
3.
When all the
button lights blink
continuously,
the machine is
warming up.
(This will take
about 1 min.)
2.
WARNING! The Steam Wand tube for dispensing hot water and steam reaches
very high temperatures - Danger of scalding! The Tube must only be handled
using the *special rubber grip. After each use, clean the tube with a damp cloth.
*Special Rubber Grip
Turn the control
lever forward,
towards you.
This will start
dispensing
hot water.
2.
3.

FROTHING / DISPENSING STEAM
10.
WARNING! During preparation
there may be some brief splashes
of hot water and the steam wand
reaches very high temperatures
- Danger of scalding! The Tube
must only be handled using the
*special rubber grip.
Place a metal
container or cup
under steam
wand spout.
Turn the control
lever backwards
(towards the back
of the machine).
This will discharge
any water left in
the circuit.
1. 2.
After a few seconds
only steam will start
to come out.
(Time may vary
according to external
conditions and you
may notice a change
in the pump noise.)
Return the
control lever
to the centre
and empty the
container.
3. 4.
Half fill a metal
container or cup
with milk, then
immerse the
steam wand into
the milk.
Turn the control
lever backwards
(towards the back
of the machine).
5. 6.
* Special
Rubber
Grip
Move the cup in
a slight circular
motion to ensure
the milk is evenly
heated.
BARISTA TIP: Frothing Milk;
Start with the steam wand in the
middle of the milk to heat evenly,
then move the cup so the steam wand is
in the upper 1/3 of the milk to aerate.
Steam/Heat Milk; Keep the steam wand
in the lower 1/3 of milk.
7.
!

z
PROGRAMMING THE QUANTITY OF BEVERAGE IN A CUP
NOTE: The quantity of coffee dispensed may be programmed,
from a minimum of 30ml to a maximum of 250ml.
MAINTENANCE TIP: After having prepared the milk, dispense a small amount of steam
and hot water to clean the steam wand and wipe the steam wand down with a damp cloth.
Warning! The steam wand will be hot, danger of scalding. Refer to Daily Maintenance on
Page 14 for further information on cleaning the steam wand.
NOTE: Recommended Programming/Factory Programming:
- 30ml: Single Espresso
- 60ml: Double Espresso
- 120ml: Tea (WARNING: ONLY USE TEA BUTTON FOR TEA)
Please Note: Quantities are approximate and may vary slightly between capsules.
11.
Add milk to your
beverage and enjoy!
Remember to clean
the tube with a damp
cloth after each use.
WARNING:
Steam wand tube will
be hot.
9.
FROTHING / DISPENSING STEAM - Continued
When you have
finished heating
or frothing the
milk, return the
control lever to
the centre.
8.
NOTE: Do not lift the lever while steam
is being dispensed. If the lever is lifted,
steam dispensing will stop immediately,
indicator light begins to blink in RED
and the machine beeps. To RESET the
machine, close the lever, return the
control lever to the central position and
press the Double Espresso button.
i

PROGRAMMING THE QUANTITY OF BEVERAGE IN A CUP
... CONTINUED
MAINTENANCE TIP:
Between uses, to ensure optimum product delivery, remove the used capsule
from the machine and rinse by pressing the Double Espresso button.
Switch the
machine on
using the On/Off
Switch. Wait for
approx. 1 min.
for the machine
to warm up.
ON
1.
Raise the lever to
open the capsule
compartment.
2.
Insert the
capsule, pressing
it gently into
place.
3.
Close the lever
fully and place
a cup or mug
under the coffee
dispensing spout.
4.
On reaching the
desired amount of
beverage, release
the button.
The button is now
programmed
to your desired
amount.
Press and HOLD
the desired
beverage button
through the
entire cycle.
5. 6.
Raise the lever
and eject the
used capsule into
the drawer then
close the lever.
7. !
WARNING:
There may be
some residual HOT
WATER within
the capsule area.
Stand to the side of
the machine when
opening the lever.
12.

z
GENERAL OPERATING INDICATIONS
Indicator light blinks
ORANGE and then
remains on without
blinking, it is advisable
to perform the
descaling cycle.
See Page 15 for
instructions.
DESCALING SIGNAL: HEATING:
13.
When all the
button lights
continuously blink,
the machine is
warming up.
(This will take
approx. 1 min.)
WHEN THE WATER RUNS OUT DURING OPERATION:
Fill the water
tank with fresh,
still water.
2.
The water tank
is empty when
the indicator
light blinks
RED and the
appliance emits
3 beeps.
1.
3 Beeps
Press the Double
Espresso button
(making sure there
is no capsule in the
chamber). Wait
for the machine
to complete the
priming cycle as it
fills with water.
3.
If the lever is
raised during
the delivery of
a beverage, the
machine can emit
jets of hot water.
Risk of burns!
1.
Close the lever
fully.
The indicator light
blinks RED and a
beep is emitted.
The appliance will
immediately
stop dispensing.
2.
IF THE LEVER IS RAISED:
1 Beep
Press the Double
Espresso button
to reset the
alarm.
The appliance is
ready for use.
4.3.
When the
button lights
turn on and
remain steadily
lit, the appliance
is ready for use.
4.

Gently turn
coffee dispensing
spout clockwise
by approx. 45o
until it comes
to a stop, then
remove.
Remove
top cover of
dispensing
spout and wash
components in
hot water.
Steam
Wand
Pipe
Gently remove
the steam wand
tube from the
machine pipe.
Gently separate
metal tube from
rubber grip
and wash the
components in hot
water to remove
any milk residue.
4.
6.
Use a soft damp cloth and a mild detergent
to clean the surfaces of the appliance.
DANGER: Never submerge the appliance in water.
Protect appliance from sprays and drips. Water and
electricity together constitute a risk of electrocution.
The plastic parts of the appliance
are NOT dishwasher safe.
14.
3.
5.
DAILY MAINTENANCE
Pull out the used
capsule drawer
and drip tray.
Remove the grill,
empty and rinse
with water. Dry
and replace back
into the machine.
Remove the
water tank,
empty, rinse and
replace the tank.
NOTE: The water
tank is NOT
dishwasher safe.
2.1.
Steam
Wand
Pipe
Reassemble the
steam wand
tube and gently
push the tube
onto the machine
pipe until it fits
into the grooves.
Check white nozzle
within rubber grip
to ensure there is
no build up of milk
residue blocking the
tip. Soak in warm
water until tip is
clear of blockage.
8.7.

z
DESCALING INSTRUCTIONS
Begin with
machine OFF.
Raise the
lever, ensure
no capsule in
machine.
1.
Empty and rinse
the used capsule
drawer and drip
tray. Lower lever
to close capsule
compartment.
2.
DESCALING SIGNAL: When the indicator light blinks ORANGE and the machine emits 3
beeps, please perform the descaling cycle as illustrated.
(Please note: you may miss the beeps if there is a lot of background noise, the indicator light
will alert you that descaling is required.)
PLEASE DO NOT LEAVE THE MACHINE DURING THE DESCALING PROCESS.
Remove, rinse
and empty the
water tank.
3.
Mix 125ml of the
Cafetto Organic
Descaling agent and
875ml of water (to
make 1L of solution).
Add solution to water
tank & replace onto
machine.
1Litre
Solution
4.
875ml
water
OFF
Continued on next page... >>
15.
NOTE: Descaling refers to the removal of the natural mineral build up within the
pipes of the machine. If not removed this may result in a poor quality beverage
and eventually block the pipes.
Descaling is NOT CLEANING the machine. We recommend that you continue with
your daily maintenance routine as outlined in 'Daily Maintenance' on Page 14.
The machine features an advanced program that monitors how much water
is used to dispense beverages. This measurement provides the user with
indications as to when the machine needs to be descaled.
CAREFULLY READ THE DESCALING INSTRUCTIONS IN FULL BEFORE
COMMENCING DESCALING.
If unsure, please also read the directions on the label of the Descaling Agent.
Avoid contact with eyes, skin and machine surfaces. A person must be present
during the descaling operation.
Please note: you will experience some water entering into the used capsule
drawer, this is normal.
Do not use vinegar: it could damage your appliance

DESCALING INSTRUCTIONS - Continued
*WARNING: Please carefully empty
the used capsule drawer after the
FIRST dispensing cycle (dose) to
prevent any water from overflowing
during the Descaling process.
Water in the used capsule drawer
will be hot. Risk of scalding.
Continue onto the Rinsing Instructions on next page... >>
16.
Remove the
container of
Descaling Solution.
Empty the used
capsule drawer
and drip tray.
Rinse and replace.
13.
Turn the control
lever forward
(towards you).
Place an empty
container (at
least 1 litre)
under the coffee
dispensing spout
and the steam
wand.
5. 6.
After completing the 5th cycle, the machine will be ready for the
rinse cycle. The indicator light and the Double Espresso light will
both flash.
The water tank will be empty or very close to empty and the
machine will beep. (Please note: there may be a 5 minute delay
between the indicator light and the Double Espresso light turning
on, please be patient.)
11.
Double Espresso
button will be lit
and indicator light
will blink
Press the Double
Espresso button
to start the
descaling cycle.
8.
Press and hold
the Single and
Double Espresso
buttons and
switch the
machine on.
Release buttons.
7. ON
The appliance will dispense the
descaling solution at intervals:
- 5 doses with an approx. 4-5 min
pause between each cycle.
Total time approx. 25 mins.
1st Cycle will dispense approx. 500ml of
descaling solution*, remaining cycles will
dispense approx. 25ml each cycle.
i
Do not press
any buttons
during this time.
The indicator
light blinks
alternately.
10.

z
DESCALING INSTRUCTIONS - Continued
9.
Empty and
rinse the used
capsule drawer,
the drip tray and
the container &
replace.
17
Rinse water
tank and fill it
with still fresh
drinking water
to the Max line.
1. 2.
Place a container
under the coffee
dispensing spout
(at least 600ml).
RINSING:
3.
Press the Double
Espresso button
to start the rinse
cycle. Fresh
water will be
run through the
machine to rinse
(approx. 500ml).
4.
When the rinse
cycle is complete,
the machine beeps
and the indicator
light is lit steadily in
ORANGE.
Beep
When all the
button lights
continuously blink,
the machine is
warming up.
(This will take
approx. 1 min.)
Set the control
lever back to the
central position
6.5.
8.
Rinse water tank
and fill it with still,
fresh drinking
water to the
Max line.
If the lights
are lit steadily,
this means
the machine
has already
warmed up.
7.
Your machine is now ready to use.
Enjoy!

18.
Locate the gasket
that was supplied
in the box.
Raise the lever.
2.
CHANGING THE GASKET
Close the
lever.
Remove the worn
gasket.
Insert the new
gasket, ensuring
that it fits snugly
into place.
CAUTION! If the gasket shows signs of wear, such as small cuts or cracks and
warping, you can replace it easily using the spare gasket supplied in the pack.
Perform the following actions only when the machine is cold. Contact with the
inside surfaces of the machine could cause scalding.
1.
3.
SAVING ENERGY
4.
To restore
normal operating
conditions, press
any button or
raise the lever.
The appliance will
start warming up.
When all the
buttons turn
on and remain
steadily lit, the
appliance is ready
for use.
The machine will
automatically
reduce power
consumption
1 hour after
inactivity.
1. 2.
All the buttons
will slowly and
sequentially blink.
1Hr
3.

z
RESTORE ORIGINAL SETTINGS (RESET)
These instructions will allow you to reset the machine back to its original factory settings
– Helpful if you experience an issue with the machine, or you have changed the pour
levels for example and cannot change them back to their original levels.
If you try to reset after experiencing a problem with the machine, resetting
may not always solve the problem. If this is the case, please contact
Roasting Australia Customer Service on: 02 9846 0307.
Hold down the Single Espresso button lit in white.
WHILE holding the Single Espresso button down….
…SWITCH ON the machine and after 1 second,
close and open the lever.
When you hear 5 beeps, RELEASE the Single
Espresso button.
1sec
ON
3.
5 Beeps
19.
Switch the
machine OFF
using the ON/
OFF switch.
Start with the
lever up and
ensure the
steam wand
control lever is
in the central
position.
OFF
1. 2.
If you don’t hear
the 5 beeps,
repeat Step 3
again. It’s all in
the timing.
At the end of this procedure,
you MUST go back and
perform the 'First Time Use'
steps on Page 6.
4. 5.
5 Beeps