Caframo Sirocco II Elite User manual

OPERATING INSTRUCTIONS
INSTRUCTIONS DE FONCTIONNEMENT
Caframo Limited, 501273 Grey Road 1, Georgian Blus ON N0H 2T0, Canada
Toll-free: 800-567-3556 • Phone: [phone] • Fax: [phone]
www.caframo.com [email protected]
7012CAWBX 12/24V White Fan
7012CABBX 12/24V Black Fan
Versatile: 12V or 24V
Polyvalent : pour 12 ou 24 volts
7012MN001 Rev00

1. Installation:
I. Test the positioning of the fan
before starting installation. Place
one nut in each hex hole on
back of the backing plate before
mounting. Use the provided
double-sided tape to temporarily
attach backing plate to the wall.
Please note that this is a semi-
permanent adhesive.
THANK YOU FOR PURCHASING A SIROCCO II ELITE FAN!
READ AND SAVE THESE INSTRUCTIONS
Your new fan can be mounted on fibreglass, plywood, steel or aluminium.
Installation requires a Phillips screwdriver, pliers and six #6 fasteners (not
included).
Accessory Kit includes:
Backing plate
Hardware bag Double-sided tape
Power cord
Place nuts in hex holes on back of backing
plate before mounting.
II. Secure backing plate to wall
using six #6 fasteners (not
included).
Fasten here
Please Note: The Sirocco II Elite features a powerful and ecient brushless motor. When
turning on the fan, there will be a slight hesitation before the blade starts to spin. This is normal
and is evidence that your fan is equipped with a long-lasting, high-performance, brushless
motor. If you have any questions or concerns about your new fan, please contact Customer
Service at: 1-800-567-3556.
2 x 2.2mm brass nuts
2 x 3.2mm stainless steel
nuts
2 x lock washers
2 x screws
1 x backing plate
1 x double-sided adhesive
pad
1.

III. Wiring
Attach corresponding wires
a) Ensure nuts are fully
tightened. Attach the
wire marked positive
to the positive base
screw, then negative
to negative base
screw.
Wire notch
Corresponding
holes
OR
Brass Nut
Lock Washer
Wire
Base screw
Mounting Surface Screw Size Fastener Length Tin Type Head Type
Fiberglass
No.6
(3.5mm)
0.5"
(12 mm)
Drilling
Rounded
Wood Pointed
Steel Drilling
Aluminum Sheet Drilling
Aluminium Heavy gauge Drilling
Recommended Screw Chart for mounting the Sirocco II Elite
b) Secure wires as
shown in the
illustration to the
right. Use pliers to
tighten nuts.
Do not rely on hand
tightening.
c) Depending on installation, feed wire through the notch on either end of
base OR through corresponding holes on the backing plate.
2.

2. Operation
Ensure blade is clear of any obstructions that would cause it to jam. Lock fan arm
in position before turning on.
I. Lock Latch
Flip Lock Latch upwards to unlock fan arm. Rotate fan arm to desired
direction. Push latch back down to lock fan in position.
II. Speed
Press Power/Speed button once for low speed, twice for medium, three times
for high, four times for full speed, and five times to turn o.
IV. Slide fan base onto firmly secured backing plate. Secure fan to backing plate
using the two provided screws.
a) Slide fan onto backing plate.
b) Secure with screws.
Power/Speed Button Timer Button
Secure with screws
Slide onto
backing
plate
Fan arm
Lock Latch in locked position
3.

III. Timer
The Sirocco II Elite is equipped with a timer feature that allows it to be set to a
run time of 3, 6, 9 or 12 hours.
To set the timer, press the Timer Button 1, 2, 3 or 4 times. The LED bar will light
up beside the selected time and the fan will shut o when the timer setting
expires.
To turn the fan o at any time, press the Timer Button until the LED bars
disappear, then press the Power/Speed button to turn the fan o.
LED Timer Bars
4. Care and Maintenance
The Sirocco II Elite requires very little maintenance. Following the instructions in
this manual will help to ensure that it operates problem-free for years.
To clean: Always turn the fan's power o before cleaning. A vacuum cleaner can
be used to clear the fan of dust build-up and a dry cloth may be used to
wipe its surface. Do not use gasoline, thinner or other harsh chemicals to clean
the fan.
3. Specifications
Speed Setting: 1 2 3 4
Draw in Amps (12V) 0.16 0.33 0.6 1.01
Draw in Amps (24V) 0.08 0.17 0.32 0.52
Airflow (CFM) 110-240
Speed (RPM) 1000 1300 1600 1900
4.

5. Safety
Reverse polarity protection ensures protection of the fan if the input supply is
connected in the reverse way.
Overcurrent protection ensures protection against short circuit or damage to the
motor.
The Sirocco II Elite is equipped with Rotor-Lock protection. This feature protects
the fan from overheating by automatically turning o the motor should an object
obstruct the blade from spinning as it would under normal operation. The fan will
automatically restart the motor every 30 seconds until the obstruction to the blade
is removed and the blade is able to rotate normally.
If the fan is operating when a power outage occurs, it will automatically restart at
the lowest speed setting when power is restored.
6. Warnings
To ensure your safety and the life of the fan, please observe the following:
•Do not position the fan too closely to any object or material that may be sucked
or drawn into the blade.
•Do not allow any object to obstruct or stop the spinning of the blade. Inhibiting
the blade’s ability to spin may result in a shortened lifespan.
• Do not use outdoors.
• Do not use on wet surfaces or immerse in water.
•Do not allow water, cleaning products or other liquids to be sprayed onto the
fan’s motor housing or controls.
• Do not use if the power supply cord becomes frayed, brittle or damaged.
• Do not use gasoline, thinners or other harsh chemicals to clean the fan.
•Do not use near fireplaces, furnaces, stoves or mechanical equipment that
produce excessive heat.
•This fan is not to be used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction.
• Children should be supervised to ensure that they do not play with the fan.
5.

LIMITED WARRANTY
www.caframo.com/warranty
This product has a 4 year limited warranty from the date of purchase.
Limited Warranty
The product you have purchased has been guaranteed by the manufacturer for the
warranty period stated starting on the date of purchase against defects in
workmanship and/or materials. If a manufacturer defect is found in an end-user
replaceable part, you will be sent a new part without charge, not a replacement fan. If a
replacement part is required, it will only be shipped to the country where the product
was purchased. For example, if you purchased the product in Canada and need a
replacement part sent to you, a Canadian shipping address must be supplied.
Only parts that prove to be defective during the period of guarantee will be replaced
without charge.
This guarantee does not apply if damage occurs during shipping, from abuse, misuse
or from unauthorized repairs made or attempted. The product is also not guaranteed
for damage that occurs because of accident, improper handling or operation.
This guarantee does not apply if the product is used in commercial or industrial
applications.
This guarantee does not apply to excessive use scenarios where the product is
operated for more than 12 hours per day on a daily basis.
When goods are sold in AU or NZ, our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
In order to claim the warranty on a purchased product, you may contact us at
Customer Service:
Outside U.S/Canada
[phone]
U.S/Canada -Toll free
1-800-567-3556
[email protected]
Caframo Limited 501273 Grey Road 1, Georgian Blus ON N0H 2T0, Canada
Toll-free: 800-567-3556 • Phone: [phone] • Fax: [phone]
www.caframo.com

1. Installation:
I. Tester le positionnement du
ventilateur avant de commencer
l’installation. Avant le montage,
placer un écrou dans chaque trou
hexagonal, à l’arrière de la plaque
de fixation. Utiliser le ruban
adhésif à double face fourni pour
fixer temporairement la plaque de
fixation au mur. Noter que c’est un
adhésif semi-permanent.
MERCI D’AVOIR ACHETÉ UN VENTILATEUR SIROCCO II ELITE !
LIRE ET CONSERVER CES INSTRUCTIONS
Vous pouvez installer votre nouveau ventilateur sur une surface en fibre de verre, en
contreplaqué, en acier ou en aluminium. Son installation requiert un tournevis
cruciforme, des pinces et des fixations no 6 (non comprises).
Contenu du jeu
d’accessoires:
2 écrous en laiton de 2,2
mm
2 écrous en acier
inoxydable de 3,2 mm
2 rondelles de blocage
2 vis
1 plaque de fixation
1 ruban adhésif à double
face
Plaque de fixation
Sac de quincaillerie Ruban adhésif double face
Cordon d’alimentation
II. Fixer la plaque de fixation au
mur avec les 6 fixations no 6 (non
comprises).
Fixer ici
Placer les écrous dans les trous
hexagonaux à l’arrière de la plaque de
fixation; avant le montage
REMARQUE : Le modèle Sirocco II Elite est muni d’un moteur sans brosse très efficace
et puissant. Lors de la mise en marche du ventilateur, une légère hésitation précède le
mouvement de l’hélice. Ceci est normal et indique que votre ventilateur est équipé d’un
moteur sans brosse, de haute performance, et de longue durée. Pour toute question ou
soucis concernant votre nouveau ventilateur, veuillez communiquer avec le service à la
clientèle au numéro sans frais 1-800-567-3556.
1.

III. Filage
a) S’assurer que les
écrous soient bien
serrés. Fixer le fil
marqué positif sur la
borne positive, puis
le négatif sur la
borne négative.
b)
c) Dépendant de l’installation, acheminer le fil soit dans l’encoche ou sur le bout
de la base OU dans les trous correspondants sur la plaque de fixation.
Encoche pour fils
Écrou en laiton
Rondelle de blocage
Fil
Vis de base
Fixer les fils correspondants
Trous
correspondants
OU
Fixer les fils tels
qu’illustré dans
l’illustration à droite.
Utiliser des pinces
pour serrer les
écrous.
Ne pas se fier à un
serrage à la main.
2.

2. Fonctionnement
S’assurer que l’hélice soit libre de quelque obstruction qui puisse la bloquer.
Verrouiller le bras du ventilateur en position, avant la mise en marche.
I. Taquet de blocage
Basculer le taquet de blocage vers le haut, pour débloquer le bras du ventilateur.
Pivoter le bras du ventilateur à la position voulue. Pousser le loquet vers le bas
pour bloquer le ventilateur en position.
II. Vitesse
Presser sur le bouton marche-arrêt/vitesse une seule fois pour la basse vitesse,
deux fois pour la vitesse moyenne, trois fois pour la grande vitesse, quatre fois
pour la vitesse maximale, ou cinq fois pour l’éteindre.
IV. Glisser la base du ventilateur sur la plaque de fixation solidement fixée. Fixer le
ventilateur sur la plaque de fixation, à l’aide des deux vis fournies.
a) Glisser le ventilateur sur la plaque de fixation.
b) Fixer avec les vis.
Bouton marche-arrêt/vitesse Bouton de minuterie
Fixer avec les vis
Glisser sur
la plaque de
fixation
Taquet de blocage dans la position
Bras du ventilateur
3.