Cambium Networks Force 110 User manual

1
Force 110 Assembly Guide

2
Front view showing
Step 1 - Align Center feed tube to the dish. Cables go through the dish. The Center feed is used as an alignment tool.
Step 2 – First Align keyway.
NOTE: DO NOT PINCH OR BIND THE CABLES.

3
Step 3 - Press Center feed to seat on the surface of the Dish.
NOTE: Make sure that the Center Feed lip is flush with the Dish.
NOTE: DO NOT PINCH OR BIND THE CABLES.

4
Rear view showing
Step 4 - Flip dish and Center feed over. The Center feed assembly to the dish will have press fit and not a slip fit.
Figure 1 - Mounting to the Right side of a pole. Figure 2 - Mounting to the Left side of a pole.
Step 5
NOTE: DO NOT PINCH OR BIND THE CABLES.
NOTE: DETERMINE THE PROPER POLE ORIENTATION BEFORE FULL ASSEMBLY.

5
Rear view showing
Step 6 Assembly Bottom Housing to dish. Align key way of the Center feed to the Bottom housing. Hold all pieces when
flipping over to install screw assembly.
Step 7 – 4X: Screw Assembly order: M6 SHCS / Split Washer / Flat Washer (round surface facing down as shown).

6
Front view showing
Step 8 – 4X: Insert screw / spring washer and flat washer to assemble. Finger tight the screws.
Step 9 Tighten in a crisscross pattern. Torque to 10.8Nm (8.0 ft lbf)
4X - 10Nm (8ft-lbs)

7
Step 10 – Push on the Centerfeed firmly until you hear the 4 lock clips engaging (a clipping sound).
Step 11 –If the snaps are not fully engaged. Use a flat head screwdriver to engage the snaps.

8

9
Step 12 – Assemble the Pole mounting bracket. Flat side of the Carriage bolt is to be installed from the inside of the Bracket (as shown).
Insert Carriage bolts - one though square opening and the other though the curved opening.
Step 13 – A) Slide on Bracket Pole Mount though Cariage bolts.
B) Slide on Bracket Pole Mount Clamp though Cariage bolts (keep open slot up).
C) Slide on Bracket Pole Mount Retainer though Cariage bolts to cover open slot of the
Bracket Pole Mount Clamp .
D) Screw on Flange Hex nuts to Cariage bolts.

10
Step 14 - Secondary Clip insertion. Do this for all four corners.Ensure that the Clips are facing outwards.

11
Press firmly on the Retainer Clips when assembling to the dish..

12
Step 15 - Inserting Secondary Clip Cover. Keep notch facing outward. Do this for all four clips.
Step 16 – With the radio pointing up, attach the Cambium Networks Logo Medallion to the Secondary antenna.

13
Attaching the CSM radio to the Force 110
Step 17 – Gray shielding is H / Black shielding is V Keep cables to the side of the upper radio mount.
Step 18 - Tighten SMA CONNECTORS.
NOTE: DO NOT PINCH OR BIND THE CABLES.
1Nm (8in-lbs)

14
Step 19 – Keep cable to the left and right of the center support mount. Slide on the ePMP CSM radio.
Step 20 - Tighten the M5 lock screw to a TORQUE of 6.0 Nm (4.43 ft lbf)
NOTE: DO NOT PINCH OR BIND THE CABLES.

15
Step 21 – Slide Cover down until you hear a click.
ASSEMBLY IS NOW COMPLETE

16
ITEM
NO
QTY DESCRIPTION
1
2
BOLT-RHSN_M8X90MM_316SS
2
1
BOTTOM-HOUSING
3
1
BRACKET-POLE MOUNT
4
1
BRACKET, POLE MOUNT, CLAMP
5
1
BRACKET, POLE MOUNT, RETAINER
6
1
CENTER FEED 81mm
7
4
CLIP, RETAINER, COVER
8
4
CLIP, RETAINER, SUBREFLECTOR
9
1
COVER-BOTTOM-HOUSING
10
1
COVER, SUB-REFLECTOR
11
1
DISH-BRACKET-MOUNT
12
1
DISH, 450MM
13
1
FRAME, SUB-REFLECTOR
14
2
NUT-FLANGE-HEX-LOCKNUT-M8
15
4
SCREW, M6x1x14mm, 316SS
16
4
WASHER, M6 x 6.5mm ID x1.5mm
17
4
WASHER, SPLIT LOCK, M6 SCREW, SS