CAME BPT XTS 5IP WH Manual

Handsfree entry phone for IP360 system
XTS 5IP WH - XTS 5IP BK
INSTALLATION AND CONFIGURATION MANUAL
EN
English
FB01266-EN

4
2
1
3
Page 2- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Description of parts
Front view
1Signaling LED
2Speaker
3Touch-screen display
4Microphone.
Rear view
5Socket for connecting the device to the LAN PoE
network.
Green LED, activity on the network:
permanently lit = active link,
flashing = data activity.
Yellow LED, data transmission speed:
o 10Mbps,
on 100Mbps.
The device automatically recognises the local
or PoE power supply.
DESCRIPTION
Full-touch speaker video intercom for IP360 system, 5˝ TFT touch screen display and Graphical User Interface.
General Precautions
• Read the instructions carefully before beginning the installation and carry out the actions as specified by the
manufacturer.
• The installation, programming, commissioning and maintenance of the product must only be carried out by
qualified technicians, properly trained in compliance with the regulations in force, including health and safety
measures and the disposal of packaging.
• Before carrying out any cleaning or maintenance operation, disconnect the device from the power supply.
• Use this equipment solely for the its specifically intended purpose.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.

5
F
Page 3- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
FReset button. When pressed it reboots the device; this operation DOES NOT require any deleting of program-
ming.
Function of terminals
Local power supply input
Landing call input
Alarm input
Technical data
Type XTS 5IP
local power supply (V DC) 14 to 18
PoE power supply IEEE 802.3af-PD
Maximum draw (mA) 330
Current draw in stand-by mode (mA) 270
Stocking temperature °C -25 to +70
Operating temperature °C 0 to +40
Protection rating (IP) 30
Video codec H.264
Capacitative TFT Touch-screen Display (pixels) 800 x 480

98 mm
138 mm
24 mm
1
83,5 mm
3
2
4
H= 155 -165 cm
H= 125 -135 cm
Page 4- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
INSTALLATION

5
Page 5- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
To make the device's installation more solid, use
the supplied screws and dowels to fasten the frame
to the wall.

MTMV/IP VAS/101
VAS/101
Modem router Wi-Fi
MTMV/IP
Modem router Wi-Fi
Switch PoE
Page 6- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Examples of installation
Single-family system with POE power supply
Single-family system with local power supplies

MTMV/IP MTMV/IP
APARTMENT 4
APARTMENT 3
APARTMENT 1
APARTMENT 4
APARTMENT 2
SWITCH PoE
SWITCH PoE
MODEM
ROUTER Wi-Fi ETI/MiniSER
VAS/100.30
Master
Slave
Page 7- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Multi-family system with an internal receiver for each apartment; one of the receivers can be
managed from a tablet or smartphone

Page 8- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
This section requires specific
know-how in operating the vid-
eo-intercom system. Wrong set-
tings may cause partial or even
total malfunctions; that is why
the editing of some parameters
is allowed only after entering the
installer password; the default
password is 112233).
Maintenance
Advanced sengs
Conguring the user interface
Tones
Automac door opener
Display
SIP Sengs
Backdrops
Network
Auxiliary seng
Sengs
Advanced settings
Scroll the list.
Select menu item B.
Select item A.
COMMISSIONING
Once the cables are laid and connected, program the essential function for operating the device.
Scroll the available pages.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
B
A

1
Page 9- Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
StacDHCP
ALets you choose the type of address from:
DHCP
The device's IP address is assigned by the DHCP server; if there are no special needs, this mode lets you
continue with the settings without adding any additional data.
Static
The device's IP address is manually assigned.
BIf you have chosen a static IP address, enter the device's IP, which must belong to the same subnet as that of
the router and of the other connected devices.
CIf the netmask is dierent from the default one, provide the proper netmask.
DProvide the default gateway for your network.
EIndicate the DNS from which the device acquires the correct time.
Press button Fto save the configuration
If a DHCP server is also present, the static address selected must not be among those included in the
DHCP pool.
MAC address
DNS
Gateway
Netmask
IP address
Mode
Type of connecon
Save
This section is used to configure
the connection to the network.
Network
Info Back Home
21:20 Thursday
15 Mar 2018
A
B
C
D
E
F

Page 10 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
21:20 Thursday
15 Mar 2018 HomeBackInfo
Server type
Server address
Display name
Password
Mode
Flat Id
Username
DIn this space enter the server's IP address.
Default IP addresses of CAME servers (example):
ETI/MiniSER Xip, ETI/DOMO Xip - 192.168.0.3 (port 0) - 192.168.1.3 (port 1)
ETI/SER Xip, 192.168.1.1
Serverless IP entry panel, 192.168.1.5
EChoose the type of server the device is connected.
All CAME servers are of XIP Server type.
Automatic mode
Choosing the automatic SIP setting mode and pressing the [Save] button, a wizard is started through which it is
possible to choose the server or master device, to which the device must be connected. Once the call code (Flat
Id) assigned to your extension has been entered during programming from PCS/Xip, the procedure is completed.
Save
NoneGeneric
AutomacManual
XIP server
Manual Mode
AIn this space enter the “SIP User
Name” assigned to the device by
PCS Xip.
BIn this space enter the password
assigned in the receiver credentials
in the server set-up window.
CName assigned to the device
(for future use).
SIP Settings
A
B
C
D
E

1
2
3
Page 11 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Save
Save
Sun
Sun
Sat
Sat
Fri
Fri
Thu
Thu
Wed
Wed
Tue
Tue
Mon
Mon
Days of the week
Days of the week
Stop me
Stop me
Start me
Start me
C Touch the days of the week dur-
ing which the time-slot needs to be
active.
D Touch this button to save the
time-slot you have just created.
Create other new time-slots and
touch the Save button to add them
to the list.
B Touch the empty sections and
in the pop-up window set the start
and finish time of the time-slot for
activating the function.
The list is empty New
me slot
A Touch the button to add a new
time slot.
Automatic door opener
This function, which is especially useful for businesses, lets you automatically open the entrance once the call-but-
ton is pressed on the entry panel. The activation of this function can be programmed to schedule time slots and
days of the week.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
A
B
D
C

2
1
4
Page 12 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Custom: to acvate the customized user interface if programmed by tool in the server or if
congured using the buon below
Demo: to acvate a demo user interface if programmed by tool in this device
Default: to acvate the factory default user interface, which can not be changed
BIt is used to display a preview of
the interface (if present) on the de-
vice, during the design phase with
the UI Creator software.
CTouch the button to create a
customized homepage.
Configuring the user interface
Using the PC software [UI Creator], it is possible to design and program a custom graphical interface within the
system master server for the XTS device.
A With the selected button:
- If a custom graphical interface has been programmed, it will be loaded into the device.
- If a custom graphical interface has not been programmed, the configuration of the modified home page is loaded
using the Cbutton.
DFrom the drop down menu se-
lect the total number of sections
that will make up the main page.
Each page contains at most
six frames; the last one is always
the configuration frame.
Delete all
New
me slot
13:30 - 18:30
Mon Tue Wed Thu Fri
Mon Tue Wed Thu Fri
08:30 - 12:30
For editing the selected ele-
ment.
For eliminating the selected
element.
Touch the Back button to return to
the list of configurable parameters.
Customize Homepage funcons
Preset DemoCustomized
Number of frames
Acve user
interface
Save
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
D
A B
C

3
1
Page 13 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Restore preset sengs
Restart applicaon
Reboot device
(administrator password required;
the default password is 112233).
ATouch the button to reboot the
indoor receiver.
BTouch the button to reboot only
the application that runs the indoor
receiver.
CTouch the button to return all the
local settings to the default factory
settings.
Maintenance
Empty Sengs
EmptyEmpty
Touch each of the empty sections
and use the drop-down menu to
select the content that you want to
assign to the section.
Save the setting by touching the
Save button.
Number of frames
Save
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
A
B
C

Page 14 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
FILE
No file selected
VERSION
Exit
Upload
Help
Maintenance
CHANGE PASS... CONFIGUTION... UPDATE...
System
Date and Time
Network
SIP
IP video cameras
Voicemail
Maintenance
Diagnostics
Maintenance
Update
This window is for updating the
device's firmware, by proceeding
as follows:
APress the button, select the file
containing the firmware update on
your computer, and start the pro-
cess.
LANGUAGE
English
XTS 5 IP
SETTINGS
Enter
LOG-IN MODE
USER
INSTALLER
PASSWORD
Type the address of the device in the browser address bar
(Chrome, Firefox, Safari).
Select the [INSTALLER] access option and enter the password,
which is set to “112233” by default, to access the settings win-
dows.
When accessing with "User" credentials (default password
123456) only lets you browse the pages that follow, except the
user’s sections.
There is no scroll bar on the right on the settings web pag-
es. To scroll through the pages, press and hold down the right-
hand mouse button and drag. On a smartphone or tablet, drag
your finger down the screen.
SETTINGS AVAILABLE ONLY FROM WEB PAGE
The web pages, in addition to allowing the configuration of most of the parameters that can be set by the interface
of the receiver, allow provide some additional functions illustrated in this section.
A

Page 15 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Password change
In this window it is possible to
change the password used to ac-
cess.
CONFIRM NEW PASSWORD
NEW PASSWORD
PASSWORD
MODE
Local - RAM
LOG LEVEL
Warning
Exit
Exit
CancelSave
Get
Help
Help
Diagnostics
Maintenance
LOG FILES
CHANGE PASS... CONFIGUTION...
STATISTICS
UPDATE...
System
Date and Time
Network
SIP
IP video cameras
Voicemail
Maintenance
Diagnostics
System
Date and Time
Network
SIP
IP video cameras
Voicemail
Maintenance
Diagnostics
DLets you choose where to save the LOG files from:
Local-RAM: the file is saved in the non-permanent memory of the device
Local-FLASH: the file is saved in the internal memory of the device (attention!, the capacity is limited)
Remote: the file is saved on a remote server where the IP address must be entered.
EIt starts recovery of the log file.
Diagnostics
AThis section brings together
statistical data on the operation of
the device.
BThe section lets you generate
file that contain data useful for
technical servicing aimed at finding
any malfunctions.
CIt is used to choose the type of
LOGs that you want to collect.
A B
C
D
E

CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. [phone] - fax. [phone]
Page 16 - Manual FB01266 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Pertinent Regulations. This product complies with the law.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 - This device may not cause harmful interference, and
2 - This device must accept any interference received, including interference that may cause undesired operation.
Decommissioning and disposal. Dispose of the packaging and the device at the end of its life cycle responsibly,
in compliance with the laws in force in the country where the product is used. The recyclable components are
marked with a symbol and the material's ID marker.
THE DATA AND INFORMATION SHOWN IN THIS MANUAL ARE TO BE CONSIDERED AS SUBJECT TO CHANGE AT ANY
TIME AND WITHOUT THE NEED FOR ANY ADVANCE WARNING. MEASUREMENTS, UNLESS OTHERWISE INDICATED,
ARE IN MILLIMETRES.