CAME BPT XTS 5IP WH User manual

Handsfree entry phone for IP360 system
XTS 5IP WH - XTS 5IP BK
USER MANUAL
EN
English
FB01267-EN

4
2
1
3
Page 2- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Description of parts
1Signaling LED
2Speaker
3Touch-screen display
4Microphone.
DESCRIPTION
Full-touch speaker video intercom for IP360 system, 5˝ TFT touch screen display and Graphical User Interface.
GENERAL PRECAUTIONS
• Carefully read the instructions before using the device.
• The installation, programming, commissioning and maintenance of the product must only be carried out by
qualified technicians, properly trained in compliance with the regulations in force, including health and safety
measures and the disposal of packaging.
• Use this equipment solely for the its specifically intended purpose.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
Maintenance and precautions when using the device
• Do not expose the LCD screen to direct sunlight.
• To clean, only use soft, dry, or slightly-moistened cloth rags. Do not use any chemicals.
• Do not block the air vents.

M
B C F G
E
D
A
L
K
H
IJ
Page 3- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
HomeBackInfo
Video Recording
Entry panels
Contacts
Favourites
21:20
Thursday
15 Mar 2018
ACommand to exclude call ringer; when the com-
mand is active, the red LED is lit.
BThe red LED means that the device's ringer is
turned off
CThe blinking blue LED, when the screen is stand-
ing by, means that there are unseen messages or
missed calls
DTurns the answering service off or on
ETurn the automatic door opener on or off
This icon appears only if the automatic door
opener function is properly set up.
FThe blinking icon means there are unseen mes-
sages or missed calls
GThe white icon means that the device is working
properly and is ready to take any calls
HThis button appears on all screens and is for re-
turning to the homepage
IThis button appears on all screens and is for re-
turning to the previous page
JThis button appears on all screens and is for ac-
cessing the information pages
KThis activates the preset auxiliary command
LPreset door opener command
MSOS button: pressed for at least 5 seconds, it
sends a "panic" alarm signal to the default porter,
showing the number of the calling extension.
This button is featured in systems that require
a concierge service.
Commands and notifications found on the home page
The appearance of the homepage may vary according to the system configuration or the user interface.

Page 4- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Call from Entry Panel
An image of the caller appears on the screen. The audio from and towards the caller is turned o.
ATouch the button to answer the call and to turn on the audio communication.
BTouch the button to refute the call and to return to the homepage.
Options appearing on the screen during a conversation
CCall duration and door status.
DCaller's ID.
Commands that are active during a conversation
EIt turns on the electric lock of the shown entry panel.
FThis opens the list of auxiliary commands configured for the shown entry panel; touch the name of the com-
mand that you want to send.
GIt is used to adjust the audio volume of the conversation in progress.
HIt turns o the microphone (mute function).
ITouch the button the start audio/video recording the current conversation.
A red light signal blinks next to the caller's ID during the recording.
The recording is automatically ended after 10 seconds.
JIt is used to access to a list of CCTV cameras that can be viewed.
Select the camera you want to view; the audio and the door opener and auxiliary controls remain open to and from
the calling entry panel.
KTouch and drag the image on the screen (or press the lateral > arrows) to view the following/previous listed
entry panel or analog camera (if installed); the current audio/video call is ended.
HOW TO USE THE DEVICE
Answering a call

1
2
3
Page 5- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Video RecordingContacts
Entry panelsFavourites
Main Call
IP Unit
Main Call
Concierge
Main Call
Intercom 1 Not home
App 01 Call Mario's phone When communication is underway,
certain commands and information
appear on the screen, as men-
tioned before in the "Answering a
call" chapter on page 4.
Select one of the listed contacts to
initiate a call.
Touch the icon to view con-
tact's details.
Touch the icon to remove the
contact form the list of favorites.
Calling a contact on the
favorites list
ATouch the icon to access the list
of favorite contacts.
To fill the list of favorite con-
tacts, see the chapter called
"Contacts" on page 7.
Making a call
This device lets you call other indoor receivers (intercommunication), any devices connected over the Wifi network
or, any entry panels.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
2
3
Page 6- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Secondary entry panel
Video RecordingContacts
Entry panelsFavourites
NORTH ENTRANCE
EAST ENTRANCE
MAIN ENTRANCE
When communication is underway,
certain commands and information
appear on the screen, as men-
tioned before in the "Answering a
call" chapter on page 4.
Select one of the listed entry panels
to initiate a call.
This opens the door associated
to the entry panel without initiating
a call.
Opens a pop-up containing a
list of auxiliary commands associ-
ated to the entry panel.
Touch the icon to view con-
tact's details.
Touch the icon to remove the
contact form the list of favorites.
Turn on communication to
entry panel
BTouch the icon to access the list
of entry panels.
To fill the list of entry panels,
see the "Contacts" chapter on
page 7.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
2
Page 7- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Video RecordingContacts
Entry panelsFavourites
NORTH ENTRANCE
EAST ENTRANCE
Concierge
Home
MAIN ENTRANCE
Commands associated with contacts
Opens the door associated to the entry panel.
Opens a pop-up containing a list of auxiliary commands associated to the entry panel.
Adds/removes the selected to and from the favorites list.
Adds/removes the selected to and from the entry panels list.
Types of contact
Residential unit
Single User
Concierge
Entry panel
Analog video camera
Touch one of the listed items to access the window for viewing details on the selected contact and to customize
his or her name.
The list contains all the devices that
can be contacted.
Touch the icon to access the con-
tacts list.
Contacts
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

3
4
5
Page 8- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Concierge
Main entry panel
EXTENSIONS
Unit
AResidential unit
BThe indoor receiver.
CDevices belonging to the resi-
dential unit.
Touch the icon to add the con-
tact to the list of favorites.
Touch one of the contacts to initiate
a call.
Touch the Back button to return to
the previous screen.
Concierge
FConcierge panel, if the system
features this.
Touch the contact to initiate the
call.
Entry panel
DEntry panel.
ECommands associated to an
entry panel.
Touch the contact to initiate the
call.
XTS receiver
Attic XTS receiver
Cellar XTS receiver
Mobile App 1
Home
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
2
1
Page 9- Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
MessagesCCTV
Aux ListCall register
ATouch the icon to access the call
history.
BThe number with the red back-
ground is the number of missed
calls.
When the screen standing-by, any
missed calls are flagged by the
blinking, blue LED fitted on the
frame.
Call register
EAST Entry Panel
WEST Entry Panel
Main Entry Panel
Video RecordingContacts
Entry panelsFavourites
Delete all
01 Jan 2018 23:55
10s
03 Jan 2018 17:33
10s
04 Jan 2018 21:03
10s
ATouch the icon the turn the an-
swering service on or off.
To properly set up the an-
swering service, see the "Video
answering service" chapter on
page 16.
BThe number with the red back-
ground is the number of unseen
video messages.
When the screen standing-by,
any unseen video messages, are
flagged by the blinking, blue LED
fitted on the frame.
Any unseen messages are high-
lighted.
Touch the wanted message to start
its playback.
Touch the icon to remove the
message from the list.
Touch the Back button to return to
the previous screen.
Video Recording
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
2
2
Page 10 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Touch the icon to remove the message from the list.
Touch the Back button to return to the previous screen.
Light
WEST Entrance
Gate
EAST Entrance
EAST Entry Panel
Intercom 01
WEST Entry Panel
Main Entry Panel
Main Entry Panel
Delete all
MessagesCCTV
Aux ListCall register
Types of calls
Incoming call.
Outgoing call.
Missed call.
Any missed calls are highlighted .
Touch the line you want to call your
contact.
Touch the icon to start the
saved message playback.
Touch the name of the wanted
command to activate its corre-
sponding contact.
Touch the icon to edit the
command name.
Touch the Back button to return to
the previous screen.
ATouch the icon to access the list
of auxiliary contacts.
The auxiliary commands (AUX) let
you activate suitably programmed
contacts to carry out additional
commands to the classic opening
of the entry door.
To fill the list of auxiliary con-
tacts, see the chapter called "Aux
settings (auxiliary commands)"
on page 14.
Aux List
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
2
1
Page 11 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
MessagesCCTV
Aux ListCall register
ATouch the icon to display the
messages received by the con-
cierge.
Messages from the caretaker
MessagesCCTV
Aux ListCall register
IP 02 Video cameraIP 01 Video camera
Select the IP video camera that you
want to view.
ATouch the icon to access the list
of available video cameras.
To fill the list of IP cameras,
see the "IP Cameras" chapter on
page 16.
CCTV
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

2
3
3
Page 12 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Compose a new message
B Touch the button to start a new
conversation with the concierge.
D Indicate the subject of the con-
versation.
E Choose the recipient.
F Proceed with the composition of
the message.
Reply to a message
Touch the green area to activate the
keyboard on which to compose the
message.
C Touch the button to send the
message.
01 Feb 19:00
A:
Continuous
Concierge
Mail delivery
Subject:
01 Feb 14:58
Sunday I will be absent, please reset the counter if necessary
Please note that due to maintenance work electric
power cut off may occur on next Sunday from 8:00
am to 10:00 am.
Compose message
Concierge - Electric power cut off
Messages from the concierge
are grouped by conversation sub-
ject.
Any unseen messages are high-
lighted.
Touch the icon to remove the
message from the list.
Touch the line you want to view the
conversation.
New message
Delete all
Concierge
Mail delivery
13 Mar, 2018 11:52
1/1
15 Mar, 2018 12:42
1/1
Concierge
Electric power cut off
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

Page 13 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Language
Date/time
EnglishLanguage
System information
Auxiliary setting
Quick commands
Settings
Save
Choose the device interface lan-
guage from the drop-down menu.
Save the setting by touching the
Save button.
Language
This window gives technical infor-
mation that is useful for identifying
the device's characteristics and the
hardware and software versions.
System information
Touch the icon to return to the list
of settings.
GENERAL SETTINGS
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
Page 14 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
New Aux
21:20 Thursday
15 Mar 2018 HomeBackInfo
NTP
Auto
System
Manual
State/City
Continent
Date/Time
NTP server
Auto mode
Mode
The list is empty
Save
A Touch the button to add a new
auxiliary command.
Aux settings (auxiliary commands)
This window is for setting the date
and time on the indoor receiver.
A The date and time are manually
set by the user.
B Date and time are synchronized
automatically.
The network to which the de-
vice is connected must be able to
access the internet.
Choosing mode B, you can specify the source of the automatic date and time.
C Date and time are automatically synchronized with the system server (or master).
D The date and time are automatically synchronized by a corresponding internet service (NTP server).
EIn this space provide the NTP server address through which the device will synchronize the date and time.
FWhen the manual mode is activated (A), the pop-up window lets you manually set the current date and time.
GSelect from the following lists the continent - state/city where the system is installed.
Save the setting by touching the Save button.
Touch the Back button to return to the list of configurable parameters.
Date/time
Info Back Home
21:20 Thursday
15 Mar 2018

2
3
Page 15 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
This window is used to determine
which commands are executed by
pressing the buttons on the left side
of the home page.
A Choose the destination of the
controls from the lists.
Touch the Back button to return to
the list of configurable parameters.
Quick commands
EAST stairwell light
Entry panel
Preset Aux command
Destination
Main concierge
Aux 3
Default concierge call
Command
EAST Entrance
Gate opener
Garden lights
Entry panel
Gate opener
Entry panel
Pre-set door release
Description
Delete all
New Aux
Save
The auxiliary commands will fill the
list.
For editing the selected ele-
ment.
For eliminating the selected
element.
Touch the Back button to return to
the list of configurable parameters.
B Touch the area to assign a name
to the AUX command that you are
going to add.
C Choose the command to asso-
ciate the AUX to, from the list.
D Choose the destination of the
AUX command from the list.
Save the setting by touching the
Save button.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
Page 16 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
New
IP cameras
The list is empty
Save
5 secondsAnswer delay
Courtesy message Off
Play message
Record message
On
A From the drop down menu, se-
lect the ring time - expressed in
seconds - after which the automat-
ic recording is activated.
B Enable the courtesy message to
be played back.
C Button for recording and playing
back the courtesy message.
Save the setting by touching the
Save button.
Touch the Back button to return to
the list of configurable parameters.
Video Recording
If the system has a video intercom entry panel installed, if the called user is not in, the device lets the caller record
a video message.
The caller may be notified of this by a courtesy message, for example, "The user is not available at the moment,
please leave a message after the beep".
The video message, labelled with the time and date of the call, are stored. You can view it later by consulting video
voicemail.
A Touch the button to add a new
IP video camera.
IP cameras
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

2
3
Page 17 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Background
IP 02 Video camera
IP 01 Video camera
Delete all
New
IP cameras
21:20 Thursday
15 Mar 2018 HomeBackInfo
Save
URI for the xed image
URI for live connection
Description
Select your preferred backdrop;;
the new configuration is applied
immediately.
Touch the Back button to return to
the list of configurable parameters.
Backdrops
B Touch the area to assign a name
to the IP video camera that you are
going to add.
C Touch the area and type the
URI string for connecting the video
camera.
D Touch the area and type the URI
string for acquiring the static image
from the video camera, needed for
the preview.
The URI strings are indicated
in the IP cameras manual.
Save the setting by touching the
Save button.
The added IP video cameras fill the
list.
For editing the selected ele-
ment.
For eliminating the selected
element.
Touch the Back button to return to
the list of configurable parameters.
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

Page 18 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Brightness in stand-by
Touch sound
Local doorbell tone
Ringing tone
Volume
Brightness
Clean screen
D With this function enabled, each touch on the screen is accompanied by a sound.
Touch the Back button to return to the list of configurable parameters.
A Adjusts the brightness of the
screen during use.
B Adjusts the brightness of the
screen saver when the screen is in
stand-by mode.
C This makes the screen insensi-
tive to the touch for 20 seconds, to
enable cleaning over it.
Touch the Back button to return to
the list of configurable parameters.
A It adjusts the general volume of
the ringers for the video intercom
calls.
B Choose the tone to associate to
incoming calls from the drop-down
menu.
C From the drop down menu se-
lect the tone to associate to the call
from the landing.
Tones
Display
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

1
Page 19 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
StaticDHCP
Static
The device's IP address is manually assigned.
BIf you have chosen a static IP address, enter the device's IP, which must belong to the same subnet as that of
the router and of the other connected devices.
CIf the netmask is dierent from the default one, provide the proper netmask.
DProvide the default gateway for your network.
EIndicate the DNS from which the device acquires the correct time.
Press button Fto save the configuration
If a DHCP server is also present, the static address selected must not be among those included in the
DHCP pool.
MAC address
DNS
Gateway
Netmask
IP address
Mode
Type of connection
Save
This section is used to configure
the connection to the network.
ALets you choose the type of ad-
dress from:
DHCP
The device's IP address is as-
signed by the DHCP server; if
there are no special needs, this
mode lets you continue with the
settings without adding any ad-
ditional data.
Network
This section requires specific
know-how in operating the vid-
eo-intercom system. Wrong set-
tings may cause partial or even
total malfunctions; that is why
the editing of some parameters
is allowed only after entering the
installer password; the default
password is 112233).
Maintenance
Conguring the user interface
Automatic door opener
SIP Settings
Network
Advanced settings
Info Back Home
21:20 Thursday
15 Mar 2018
Info Back Home
21:20 Thursday
15 Mar 2018

Page 20 - Manual FB01267 -EN - 12/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
21:20 Thursday
15 Mar 2018 HomeBackInfo
Server type
Server address
Display name
Password
Mode
Flat Id
Username
DIn this space enter the server's IP address.
Default IP addresses of CAME servers (example):
ETI/MiniSER Xip, ETI/DOMO Xip - 192.168.0.3 (port 0) - 192.168.1.3 (port 1)
ETI/SER Xip, 192.168.1.1
Serverless IP entry panel, 192.168.1.5
EChoose the type of server the device is connected.
Automatic mode
Choosing the automatic SIP setting mode and pressing the [Save] button, a wizard is started through which it is
possible to choose the server or master device, to which the device must be connected. Once the call code (Flat
Id) assigned to your extension has been entered during programming from PCS/Xip, the procedure is completed.
Save
NoneGeneric
AutomaticManual
XIP server
Manual Mode
AIn this space enter the “SIP User
Name” assigned to the device by
PCS Xip.
BIn this space enter the password
assigned in the receiver credentials
in the server set-up window.
CName assigned to the device
(for future use).
SIP Settings