CAME XTS 7IP BK WIFI Manual

Video intercoms for the IP360 system
XTS 7IP WH WIFI
XTS 7IP BK WIFI
XTS 7IP WH WFBF
INSTALLATION AND SETTINGS MANUAL
EN
English
FB01185-EN

4
2
1
3
p. 2- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
GENERAL PRECAUTIONS
• Read the instructions carefully before beginning the installation and carry out the actions as specified by the
manufacturer.
• The installation, programming, commissioning and maintenance of the product must only be carried out by
qualified technicians, properly trained in compliance with the regulations in force, including health and safety
measures and the disposal of packaging.
• Before carrying out any cleaning or maintenance operation, disconnect the device from the power supply.
• The equipment must be destined solely for the use for which it was expressly designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
Cautionary issues on remotely controlling the device
Some features of the system may be managed by smartphones and tablet PCs, by using the corresponding apps.
For the system to be remotely controlled, the device must be connected to a home WiFi network with internet
access.
This type of system functions properly when:
- the device receives a high-quality WiFi signal
- there is a permanent connection established by your contract with the internet service provider. The connection
must support the data flow generated by the device and support VoIP,
- the smartphone or table PC on which the corresponding app is running does not block any VoIP apps.
Remotely controlling the device via app means that the data trac consumption takes place over the
home network of the smartphone or table PC. the ensuing cost of said consumption is borne by the user.
DESCRIPTION
Full-touch video intercom for the IP360 system, with TFT seven-inch touch-screen, featuring WiFi and User Graph-
ic User Interface.
Description of parts
Front view
1Signaling LED
2Loudspeaker
3Touch-screen display
4Microphone.
Rear view
5Socket for connecting the device to the LAN or
LAN PoE network.
Green LED, network activity:
on steady = active link,
blinking = data activity.
Yellow LED, data transmission speed:
o 10Mbps,

E F
p. 3- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
The device automatically recognises the local or PoE power supply.
F Reset button. When pressed it reboots the device; this operation DOES NOT require any deleting of program-
ming.
Function of terminals
Local power supply input
Landing call input
Alarm input
Technical data
Type XTS 7IP WIFI
local power supply (V DC) 14 to 18
PoE power supply IEEE 802.3af-PD
Maximum draw (mA) 420
Consumption in stand-by mode (mA) 340
Stocking temperature °C -25 to +70
Operating temperature °C 0 to +40
Protection rating (IP) 30
Video codec H.264
Capacitative TFT Touch-screen Display (pixels) 1024 x 600
Wireless standard IEEE 802.11b/g/n
Wireless frequency filed (MHz) 2.412 - 2.472
Maximum transmission strength (dBm) 16
Wireless security WPA/WPA2-PSK, WEP

129 mm
24 mm
185 mm
1
83,5 mm
3
2
4
H= 155 -165 cm
H= 125 -135 cm
p. 4- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
INSTALLING

5
p. 5- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
To make the device's installation more solid, use
the supplied screws and dowels to fasten the frame
to the wall.
Signal quality
Optimal
Good
Sucient
Insucient
Notes on installing indoor receivers connected to the WiFi network
Install the indoor receiver: away from any metal objects that may interfere with the signal, or from any devices
that generate magnetic fields. Install it in the same room as the router or have the least possible number of walls
separating the router and the indoor receiver.
If the place chosen for installing the indoor receiver is not easily reached by a suciently intense WiFi signal, we
suggest installing a signal regeneration processor which is easily bought on the open market.
Reinforced concrete
Supporting wall
Stone wall
Wooden wall
Plasterboard wall
Light-brick wall

MTMV/IP
Modem router Wi-Fi
Switch PoE
Master
Slave
MTMV/IP VAS/101
VAS/101
Modem router Wi-Fi
Master
Slave
p. 6- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
Examples of installation
The devices' Master/Slave setting is programmed via the PCS/XIP software.
Single-household system with PoE power-supply
Single-household system with local power-supply and WiFi-connected indoor receiver

MTMV/IP MTMV/IP
APARTMENT 4 APARTMENT 3
APARTMENT 2 APARTMENT 1
APARTMENT 3
APARTMENT 1
APARTMENT 4
APARTMENT 2
MODEM
ROUTER Wi-Fi
SWITCH PoE
SWITCH PoE
MODEM
ROUTER Wi-Fi
MODEM
ROUTER Wi-Fi
MODEM
ROUTER Wi-Fi
Master
Slave
p. 7- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
Multi-household system with indoor receiver for apartments

MTMV/IP
MODEM
ROUTER Wi-Fi
10.0.X.X
10.0.X.X
10.0.X.X
192.168.X.X
10.0.X.X
SWITCH PoE
SWITCH PoE
Switch PoE
Master
Slave
APARTMENT 1
p. 8- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
In households with several indoor receivers, where one of these is connected to the apartment
building's LAN network, while the others are connected to the local LAN network
A call from the entry panel can call, at most, 20 devices, that are
managed by the Master indoor receiver in one apartment, whether
they are connected to the LAN line or reachable via the WiFi network
or the mobile phone network via the CAME Connect service.
When there's an incoming call, all the devices programmed to answer
will ring.
The caller's image preview may be viewed on five devices, at most.
One of these is the Master indoor receiver.
The high resolution image can only be viewed on the Master indoor
receiver.
Another four devices, chosen via the PCS/XIP software, can preview
the caller's image in low resolution.
Any other devices that are programmed to answer calls, may ring but
cannot view any type of video preview; only be answering the incom-
ing call can they view images from the entry panel.

MTMV/IP
MODEM
ROUTER Wi-Fi
10.0.X.X
10.0.X.X
10.0.X.X
10.0.X.X
10.0.X.X
10.0.X.X
SWITCH PoE
SWITCH PoE
Master
Slave
APARTMENT 1
p. 9- Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
Household in which several indoor receivers are installed, some of which are connected to the
apartment building's LAN network
A call from the entry panel can call, at most, 20 devices, that are
managed by the Master indoor receiver in one apartment, whether
they are connected to the LAN line or reachable via the WiFi network
or the mobile phone network via the CAME Connect service.
When there is an incoming call, all the devices programmed to answer
will ring.
The caller's image preview can be viewed by up to five devices, one of
which will always be the master indoor receiver.
The high resolution image can be viewed on the master indoor re-
ceiver and on at most four other indoor receiver connected to the LAN
network.
If only one, that is, the master indoor receiver is connected to the LAN,
the other four devices, chosen via the PCS/XIP software, can view the
caller's image in low resolution.
Any other devices programmed to answer calls will rings but they can-
not view any video previews; only be answering the incoming call can
they view images from the entry panel.

MTMV/IP
MODEM
ROUTER Wi-Fi
10.0.X.X
10.0.X.X
10.0.X.X
10.0.X.X
SWITCH PoE
SWITCH PoE
ETI/MiniSER
Master
Slave
APARTMENT 1
Switch PoE
192.168.X.X
p. 10 - Manual FB01185 -EN - 06/2018 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - This is a translation of the original instructions
Household in which several indoor receivers are connected to the local network, on which the local
ETI/MiniSER server acts as master for the apartment
An incoming call from the entry panel can have up to 10 devices ring; whether they are connected to the LAN line
or reachable over the WiFi network or the mobile network via CAME Connect.
When there's an incoming call, all the devices programmed to answer will ring.
The high resolution image is viewable by the 10 slave indoor-receivers.