CAME AGT A200K User manual

AGTK200A03K
HPC/1
AGT A200K
A/200N
HA/200
AGT A200K + TARGHA KIT FA01425-EN
EN
E
n
g
l
i
sh
INSTALLATION MANUAL

AGT A200K
HA/200 A/200N
HBP HPC/1
Page 2- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
CONTENTS OF THE KIT
General precautions
• Read the instructions carefully before staring installation and perform all procedures as explained by the manufacturer.
• The installation, programming, commissioning and maintenance of the product must only be carried out by technicians who are
qualified and properly trained in compliance with the regulations in force, including as regards health and safety, and disposal of
packaging.
• The installer must ensure that the information for the user, where there is any, is provided and delivered.
• Before carrying out any cleaning or maintenance, disconnect the devices from the power supply.
• The equipment must only be used for the purpose for which it was expressly designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
• Only use soft, dry or slightly damp cloths to clean the device. Do not use any chemical products.
• These instructions must be attached to the device.
This product complies with current applicable reference standards.
DISPOSAL - Dispose of the packaging and the device at the end of its life cycle responsibly, in compliance with the laws in force
in the country in which the product is used. The recyclable components are marked with a symbol and the material ID marker.
THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE. THE MEASUREMENTS,
UNLESS OTHERWISE STATED, ARE IN MILLIMETRES.

󱫀
M1
SW11
EXT.AUX 1
LED
P. B. SW12
M1
SW11
Page 3- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
AGT A200K
Description
Intercom internal audio receiver.
Function of terminals and jumpers
Terminal board M1󱫀
5Earth
7Call from entry panel input
8Audio FROM entry panel
9Audio TO entry panel
10
AUX2: auxiliary services (24V 100 mA)
11
21 +11 to 175 VDC LED power supply
22
AUX 1 (24V 100mA)
23
24 AUX1 LED (active to earth with SW12 jumper in position
EXT.)
Function of SW11 jumper 󱫀
Remove the jumper to make the door lock release button ( )
active only with the handset raised.
Function of SW12 jumper 󱫀
EXT.: LED connected to terminal 24.
P.B.: LED connected to AUX1 key.
Technical data
Type AGT A200 K
Single LED consumption (mA) 1
Operating temperature (°C) +5 to +40
Storage temperature (°C) -25 to +70
IP Rating IP30

󱤨󱤩
󱫂󱫄 󱫄
󱤪󱫆
󱫄
503 503
Ø60
󱫈
Page 4- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Installation
• Open the device by pressing on the tab at the bottom 󱫂.
• Separate the shell from the bottom of the device.
• Fasten the bottom of the device to the box on the wall 󱫄
󱤨-󱫄󱤩-󱫄󱤪.
• Avoid overtightening the screws.
☞the box must be installed at an appropriate height for the
user.
• Once all connections have been made, reattach the shell to
the bottom of the device 󱫆.
Ringtone settings
O (red LED on)
Where there is no power to terminal 21, the
volume switches from O to Low.
Medium volume
Maximum volume
Button functions 󱫈
Door lock release
AUX 1
AUX 2

64,5
105
145
43,5
45
7,5 57
105
106
󱫀
Page 5- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
A/200N
Description
A/200N guarantees the power supply to the HPC/1 entry panel
and a maximum of 20 front plates with 6 buttons HPP/6.
It is provided with the following functions:
- 2 dual-tone call beeps for two entry panels (or for additional
call, e.g. from the landing).
- Power supply and control for solenoid lock (12 V AC, 1 A) via
a relay (inside the device) controlled by a timer, adjustable from
2 to 15 seconds using the potentiometer P1 󱫀.
- Call generator: 2 types of dual-tone beep (up to 3 internal
receivers can be connected in parallel on the same call). The
device can be powered at 12 V DC, for example by a battery or
UPS (terminals +B and 5).
The equipment does not include a battery protection device.
Function of terminals and jumpers
Terminal board A 󱫀
Network
Terminal board B 󱫀
+B Input 12 V DC (*)
5 Earth
21 Output 11 V DC
8 Common call output 1
8A Common call output 2
11 Audio from entry panel
12 Audio to entry panel
23 – Output 14 V AC
16 +
NO Normally open
relay contactsC Common
NC Normally closed
(*) The device is electronically protected against overloads and
short circuits.
Terminal board C 󱫀
5 Earth
8 Audio to internal receiver
9 Audio to internal receiver
Technical data
Type A/200N
50-60 Hz (VAC) power supply 230
Power consumption (VA) 34
Output voltages at 11 VDC (mA) 150
Output voltages at 14 VAC (mA) 650
Peak output voltages (mA) 300
Operating output voltages (mA) 650 (1A)
Storage temperature (°C) -25 to +70
Operating temperature (°C) 0 to +35
IP Rating IP30

1
2
3
Ⓐ
Ⓑ
󱫂󱫄
󱫀
Page 6- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
HA/200
Trimmers 󱫀
ⒶSpeaker audio
ⒷMicrophone audio
Technical data
Type HA/200
Power supply (VDC) 12
Max power consumption (mA) 50
Power consumption in stand-by (mA) <35
Storage temperature (°C) -25 to +70
Operating temperature (°C) -15 to +50
IP Rating IP54
Installation
• The device can be installed on DIN rails (EN 50022) on a
suitable switchboard, or on the wall using the terminal covers.
• To dismantle the device, proceed as shown in figure 2-3.
• See figure 1 for dimensions.
The power supply must always be installed horizontally.
Ensure there is correct ventilation if the power supply is
installed in a metal case.
Description
Audio module.
Functions of terminals and audio adjusters
Terminal board 󱫀
5 – power supply
21 + 12 VDC
8 common call (for call beep)
11 audio to internal receiver
12 audio from internal receiver
14 enable
In systems in which there is an enable command, terminal
14 can be connected to the earth (unit always active) or to
terminal 12 (unit active only when handset is raised).

Page 7- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
TARGHA 200
Accessories
HTS
Recess-mounting box
Frame
Cable gland joints
Spacer
Screws
KHPS
Button
Microcontact
Button spring
KHPD
Buttons
Microcontacts
Button springs
HBP
Wall-mounted base
Hole cover
Cable gland joint
Joint
Screws and expansion plugs
HPP/6 – HPP/12D
Front plate
Microcontacts with
common call
Lighting assembly
Cable holders
Hole cover

󱫀
521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
󱫂
󱫄
󱫆󱫈
󱫊󱫌
Page 8- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Recessed installation
The HTS recessed box must be walled in
flush at a suitable height, using the spacer
provided to prevent box deformation 󱫀.
In systems where the Larsen eect might
occur, the microphone can be mounted re-
motely 󱫆.
To remove the microphone from its hous-
ing, pry it o from its base using a small
screwdriver, taking care not to damage
the cabling 󱫂.
Before inserting the microphone into the
bottom of the back-box, use pliers to remove the part that is
highlighted 󱫄.
Insert the audio unit near the top of the back-box 󱫆.
Fit the microcontact (bottom right) into the correct housing 󱫈.
The front plate is equipped with a common call for the
microcontacts, to be used when other buttons are to be
installed (maximum of 4) 󱫊.
Insert the lighting unit in the relevant housing 󱫌.
Remove the two protective seals on the holes in the recessed
box and attach the back-box using the two screws provided 󱫎.
Make the connections and secure the cables using the cable
holder 󱫐.
The cable holder must be located near to the audio unit.

521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
󱫎󱫐
󱫀󱫂
󱫄󱫆
Page 9- Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Wall-mounted installation
Fix the two hole covers to the base 󱫀.
Attach the recessed box (with 3 modules
or round Ø 65 mm) flush with the wall
and at a suitable height; fix the base to
the wall using the screws and expansion
plugs provided 󱫂.
In systems where the Larsen eect
might occur, the microphone can be
mounted remotely 󱫆.
To remove the microphone from its
housing, pry it o its base using a
small screwdriver, taking care not to
damage the cabling 󱫄.
Before inserting the microphone in the
bottom part of the back-box, use pliers
to remove the part that is highlighted 󱫆.
Insert the audio unit near the top of the
base 󱫆.
Fit the microcontact (bottom right) into
the correct housing 󱫈. The front plate
is equipped with a common call for
the microcontacts, to be used when
other buttons are to be installed
(maximum of 4) 󱫊.
Insert the lighting unit in the relevant
housing 󱫌.
Make the connections and secure the
cables using the cable holder 󱫌.
The cable holder must be located near
to the audio unit.

󱫊
521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
󱫈󱫌
󱫀
󱫀󱫂
Page 10 - Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Button assembly
To write the desired information on the name card, take out the
card holder and the card 󱫀.
Personalised name cards up to a maximum of 2 mm thick can
be used.
Closing the front plate
To fit the front plate, first insert the up-
per part into the top and then, using a
2.5 hex key, tighten the locking screw
󱫀󱫂.

󱫀
󱫂
󱫆
󱫄
󱫀 󱫂
Page 11 - Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Recessing side by side
To recess boxes side by side horizontally or vertically, remove the
hole covers and insert the cable gland joints 󱫀󱫂.
The recessed boxes must be walled in flush at a suitable height,
using the spacers provided to prevent box deformation 󱫄󱫆.
Wall mounting side by side
To mount the entry panels side by side horizontally, insert two hole covers into the exposed sides, and inside, the cable gland joint
at the bottom and the joint at the top 󱫀.
Attach the assembled bases to the wall, using the screws and expansion plugs provided 󱫂.

CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. [phone] - fax. [phone]
Page 12 - Manual FA01425-EN - 08/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions