CAME AGT V Specification sheet

Video intercom with handset
AGT V AGT V BF
OPERATING AND INSTALLATION MANUAL
FA01620-EN
EN English

Page 2- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
General precautions
Read the instructions carefully before beginning the installation and carry out the procedures as specified by the manufacturer. • The installation, programming, commissioning and maintenance
of the product must only be carried out by technicians who are qualified and properly trained in compliance with the regulations in force, including as regards health and safety, and disposal of
packaging. • Before carrying out any cleaning or maintenance, disconnect the device from the power supply. • Only use this product for its intended purpose. Any other use is hazardous. • Came
S.p.A. is not liable for any damage caused by improper, erroneous or unreasonable use. • The product, in its original packaging supplied by the manufacturer, must only be transported in a closed
environment (railway carriage, containers, closed vehicles). • If the product malfunctions, stop using it and contact customer services at https://www.came.com/global/en/contact-us or via the
telephone number on the website.
The manufacture date is provided in the production batch printed on the product label. If necessary, contact us at https://www.came.com/global/en/contact-us.
The general conditions of sale are given in the ocial CAME price lists.
Legislative references
This product complies with the applicable standards in force at the time of manufacturing.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference / ((2) this device must accept any interference received, including interference that may
cause undesired operation.
Cleaning the device
To clean the device, use a soft, slightly damp cloth only. Wet the cloth with water or an ammonia solution. Alternatively, use an oil-based soap (e.g. Marseille soap) or a gentle makeup remover (e.g.
a cleanser or micellar water).
Always wipe the surface with a damp cloth (wet with just water) after cleaning. Never use alcohol-based solutions or solutions containing surfactants.
Dismantling and disposal
Dispose of the packaging and the device responsibly at the end of its life cycle, in compliance with the laws in force in the country where the product is used. The recyclable components are
marked with the material symbol and ID.
THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE.
MEASUREMENTS ARE IN MILLIMETRES, UNLESS STATED OTHERWISE.

Page 3- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
PRODUCT DATA AND INFORMATION
DESCRIPTION
AGT V (840CF-0020) -Video intercom with handset, soft-touch keys, 5" LCD display, 1 programmable AUX key, white.
AGT V BF (840CF-0030) -Video intercom with handset, soft-touch keys, 5" LCD display, 1 programmable AUX key, white. Version with hearing-impaired function for hearing-aid users.
Description of parts
1Internal receiver
2Wall-mounting support
3AUTOMATIC DOOR RELEASE function and video activation button
4Audio settings button
5AUX 2 and porter functions button
6Open door and OPEN GATE function button
7Buttons for adjusting the brightness, contrast and colour of the display.

Page 4- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Function of terminals
–
+
AL
B
–
+
AL
B
CL.RES
M/S
1Alarm input
2Landing call
3BUS-line input
4CL.RES closing resistance
5MASTER/SLAVE selector (M/S)
CL.RES jumper settings
M/S jumper settings
CL.RES jumper settings
XDV/304
CL.RES CL.RES
123
CL.RES
M/S jumper settings
MASTER SLAVE
M/S M/S

Page 5- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
LED status key
FLASHING ON OFF
Incoming call
Communication in progress
AUTOMATIC DOOR RELEASE
active
Auto-connection in progress
AUTOMATIC DOOR RELEASE
disabled
Entering melody and call ring configuration mode Ringtone volume o
The porter would like to be called back
Incoming call Door or gate open Door or gate closed

Page 6- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Size
The measurements, unless otherwise stated, are in millimetres.
Technical data
MODELS AGT V AGT V BF
Protection rating (IP) 30 30
Operating temperature (°C) +5 ÷ +40 +5 ÷ +40
Storage temperature (°C) -25 ÷ +70 -25 ÷ +70
Size (mm) 204 x 190 x 44.5 204 x 190 x 44.5
Maximum consumption from BUS (mA) 175 175
Current draw in standby mode (mA) <1 <1
Power supply from BUS (V DC) 15-20 DC 15-20 DC
Video standard PAL/NTSC PAL/NTSC
Material colour White White
Average life (hours) 150.000 150.000
(*) Before installing the product, keep it at room temperature where it has previously been stored or transported at a very high or very low temperature.
(**) The average product life is a purely indicative estimate. It applies to compliant usage, installation and maintenance conditions. It is also influenced by other factors, such as climatic and
environmental conditions.

Page 7- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Installation
1Press the small plastic tab and slide the device o the wall-mounting support to remove it.
Observe the TOP arrow.
2Fasten the wall-mounting support to the back box.
Avoid overtightening the screws.
3Make the connections.
4Refit the device to the wall-mounting support.
5To unhook the device, use a screwdriver to press in the plastic tab and slide the device upwards.
①Round back box (Ø 60 mm tube).
②Rectangular horizontal back box 503.
③Rectangular vertical back box 503.
④Ophera (PHI) back box.
The box must be installed at an appropriate height for
the user.

Page 8- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Example set-up with VA/01
The option to switch on 4 monitors at the same time is only available for systems with VA/01.
Lb
La
VA/01
L1 L2 L3
N° Slave
N° Master
Cable length
Section Cable type
La, Lb VCM/1D or UTP CAT5
L1, L2, L3 VCM/2D
Section Max. section length (m)
La + Lb 100 VCM/1D or 60 UTP/CAT 5
L1 + L2 + L3 300
La + Lb + L1 (L2, L3) 150
La + Lb + L1 + L2 + L3 600
Maximum number of internal receivers per cable type
VCM/1D
Master 4321
Slave 4567
UTP CAT5
Master 321
Slave 067

Page 9- Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Example set-up without VA/01
The option to switch on 4 monitors at the same time is only available for systems with VA/01.
VAS/101
N° Master
La
Lb
Lc
N° Slave
Cable length
Section Cable type
La, Lb VCM/1D or UTP CAT5
Lc 2x1mm² or 2x2.5mm²
Section Max. section length (m)
La + Lb 100
Lc 25 (2x1mm²) or 60 (2x2.5mm²)
La + Lb + Lc 100
Maximum number of internal receivers per cable type
VCM/1D
Master 321
Slave 037
UTP CAT5
Master 1
Slave 3

Page 10 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
STANDARD FUNCTIONS
Communicating with the outside and DOOR RELEASE function
When the bell is pressed from the outside, the video receiver rings.
Pick up the handset to answer the call.
Press the button to open the door.
Put the handset back on the hook to end the call.
Video activation
1
2
x2
Press the button to activate video communication with the outside. Where there are multiple entry panels, keep pressing the button to display all the entry
panels in sequence.
If the line is busy, the video camera will not activate. If the line is busy, you will hear three consecutive beeps.

Page 11 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Video toggling
MASTER SLAVE
Where there are calls on more than one device, all devices will
ring, but the video will only be activated on the video receivers
configured as MASTER.
MASTER SLAVE
Press the button on the SLAVE video receiver you would like
to transfer the video to.
MASTER SLAVE
Pick up the handset on the SLAVE video receiver to activate
audio communication.

Page 12 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
DOOR STATUS function
The system must be correctly set up.
Use this function to view the current door status (open/closed) via the LED on the button.
The function is active during communication with the outside.
ADVANCED FUNCTIONS
OPEN GATE and GATE STATUS function
> 3s
The open gate function is used to activate the open/close gate function and view the gate status
(open/closed) via the LED on the button.
The function must be activated during system programming.
The DOOR STATUS function is active by default. The OPEN GATE/GATE STATUS
function must be correctly configured. The two functions cannot both be active at the
same time.
Press and hold the button for more than 3 seconds to send an open or close gate
command.

Page 13 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
AUTOMATIC DOOR RELEASE function
> 5s
This function allows you to automatically open the entrance when you ring the bell from the entry
panel. Communication is not activated and the call ends automatically. It is recommended for
professional practices.
The function is available by default. It can be removed during system programming.
Press and hold the button for more than 5 seconds to activate or deactivate the function.
The LED switches on to indicate that the function is active.
Porter functions
These functions are only available where there is a porter’s desk.
Call notification from the porter
If the porter wishes to be called back, the LED turns on.
The LED turns o when communication with the porter
starts.
Request for call to porter
Press the button to let the porter know that you want to be
called back.
Alarm contact
When the alarm contact is activated, an emergency signal is
sent directly to the porter’s desk.
The video receiver will beep intermittently to signal
activation.

Page 14 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Configuring melodies and call rings
Perform the steps below in sequence.
Entering configuration mode
> 3s
Press and hold the button for at least 3 seconds.
A short buzzing sound and a red flashing LED confirm that you have entered configuration mode.
Configuring the melody associated with a call from the outside
1Press the button to listen to the melodies in sequence.
2Press the button to select the melody and automatically move on to configuring the
melody associated with the landing call.
3Alternatively, press the button to select the melody and exit programming.

Page 15 - Manual FA01620-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
Configuring the melody associated with a landing call
1Press the button to listen to the melodies in sequence.
2Press the button to select the melody and automatically move on to configuring the
number of call rings.
3Alternatively, press the button to select the melody and exit programming.
Configuring the number of call rings
1Press the button as many times as the number of rings you want (from 1 to 12 rings,
depending on the chosen melody).
Three seconds after the button was last pressed, the video receiver will simulate a
call with the chosen number of rings.
2Press to confirm your choice and exit configuration.

Adjusting brightness, contrast and colour
With the video active, press any one of the following buttons: , , or to view
the video settings menu.
From this screen, you can view and change the video parameters.
1Brightness
2Contrast
3Saturation
Use the or button to select one of the parameters.
Use the or button to increase/decrease the value of the selected parameter.
CAME S.p.A.
Via Martiri della Libertà, 15
31030 Dosson di Casier
Treviso – Italy
Tel. [phone]
Fax [phone]
[email protected] - www.came.com