Camille Bauer SINEAX AM2000 Application guide

Device handbook
SINEAX AM2000
Operating Instructions SINEAX AM2000
173 849 04/2015
Camille Bauer Metrawatt AG
Aargauerstrasse 7
CH-5610 Wohlen / Switzerland
Phone: [phone]
Telefax: [phone]
E-Mail: [e-mail]
http://www.camillebauer.com

2/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Legal information
Warning notices
In this document warning notices are used, which you have to observe to ensure personal safety and to prevent
damage to property. Depending on the degree of danger the following symbols are used:
If the warning notice is not followed death or severe personal injury
will result.
If the warning notice is not followed damage to property or severe
personal injury may result.
If the warning notice is not followed the device may be damaged or
may not fulfill the expected functionality.
Qualified personnel
The product described in this document may be handled by personnel only, which is qualified for the respective
task. Qualified personnel have the training and experience to identify risks and potential hazards when working
with the product. Qualified personnel are also able to understand and follow the given safety and warning
notices.
Intended use
The product described in this document may be used only for the application specified. The maximum electrical
supply data and ambient conditions specified in the technical data section must be adhered. For the perfect and
safe operation of the device proper transport and storage as well as professional assembly, installation,
handling and maintenance are required.
Disclaimer of liability
The content of this document has been reviewed to ensure correctness. Nevertheless it may contain errors or
inconsistencies and we cannot guarantee completeness and correctness. This is especially true for different
language versions of this document. This document is regularly reviewed and updated. Necessary corrections
will be included in subsequent version and are available via our webpage http://www.camillebauer.com.
Feedback
If you detect errors in this document or if there is necessary information missing, please inform us via e-mail to:
[e-mail]

3/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Contents
1. Introduction .....................................................................................................................5
1.1 Purpose of this document........................................................................................................5
1.2 Scope of supply.......................................................................................................................5
1.3 Further documents..................................................................................................................5
2. Safety notes.....................................................................................................................6
3. Device overview...............................................................................................................6
3.1 Brief description.......................................................................................................................6
3.2 Available measurement data...................................................................................................6
4. Mechanical mounting......................................................................................................7
4.1 Panel cutout............................................................................................................................7
4.2 Mounting of the device ............................................................................................................7
4.3 Demounting of the device........................................................................................................7
5. Electrical connections ....................................................................................................8
5.1 General safety notes ...............................................................................................................8
5.2 Terminal assignments of the I/O extensions............................................................................9
5.3 Possible cross sections and tightening torques .......................................................................9
5.4 Inputs....................................................................................................................................10
5.5 Power supply.........................................................................................................................19
5.6 Relays...................................................................................................................................19
5.7 Digital inputs and outputs......................................................................................................19
5.8 Analog outputs ......................................................................................................................20
5.9 Modbus interface RS485.......................................................................................................21
6. Commissioning..............................................................................................................22
6.1 Parametrization of the device functionality.............................................................................22
6.2 Installation check...................................................................................................................23
6.3 Simulation of I/Os..................................................................................................................23
7. Operating the device.....................................................................................................24
7.1 Operating elements...............................................................................................................24
7.2 Selecting the information to display.......................................................................................24
7.3 Measurement displays and used symbols.............................................................................25
7.4 Alarming................................................................................................................................27
7.5 Resetting measurements.......................................................................................................29
7.6 Setting / resetting of meter contents......................................................................................29
7.7 Configuration.........................................................................................................................29
7.8 Timeouts ...............................................................................................................................30
8.1 Calibration and new adjustment ............................................................................................31
8.2 Cleaning................................................................................................................................31
8.3 Battery...................................................................................................................................31
8.4 Disposal ................................................................................................................................31
9. Technical data ...............................................................................................................32
10.Dimensional drawings ..................................................................................................38

4/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Annex ...................................................................................................................................39
ADescription of measured quantities.............................................................................39
A1 Basic measurements.............................................................................................................39
A2 Harmonic analysis.................................................................................................................43
A3 System imbalance.................................................................................................................44
A4 Mean values and trend..........................................................................................................45
A5 Meters...................................................................................................................................46
BDisplay matrices ............................................................................................................47
B0 Used abbreviations for the measurements............................................................................47
B1 Display matrices for single phase system..............................................................................51
B2 Display matrices for split-phase (two-phase) systems...........................................................52
B3 Display matrices for 3-wire system, balanced load................................................................53
B4 Display matrices for 3-wire systems, unbalanced load..........................................................54
B5 Display matrices for 3-wire systems, unbalanced load, Aron.................................................55
B6 Display matrices for 4-wire system, balanced load................................................................56
B7 Display matrices for 4-wire systems, unbalanced load..........................................................57
B8 Display matrices for 4-wire system, unbalanced load, Open-Y..............................................58
CLogic functions............................................................. Fehler! Textmarke nicht definiert.
DDeclaration of conformity .............................................................................................60
D1 CE conformity .......................................................................................................................60
D2 FCC statement......................................................................................................................61
INDEX...................................................................................................................................62

5/62 Device handbook SINEAX AM2000, 173 849, 04/2015
1. Introduction
1.1 Purpose of this document
This document describes the universal measurement device for heavy-current quantities SINEAX
AM2000. It is intended to be used by:
•Installation personnel and commissioning engineers
•Service and maintenance personnel
•Planners
Scope
This handbook is valid for all hardware versions of the AM2000. Some of the functions described in this
document are available only, if the necessary optional components are included in the device.
Required knowledge
A general knowledge in the field of electrical engineering is required. For assembly and installation of the
device knowledge of applicable national safety regulations and installation standard is required.
1.2 Scope of supply
•Measurement SINEAX AM2000
•Safety instructions (multiple languages)
•Connection set: 2 mounting clamps
1.3 Further documents
The following documents are provided electronically via http://www.camillebauer.com/am2000-en :
•Safety instructions SINEAX AM2000
•Data sheet SINEAX AM2000
•Modbus basics: General description of the communication protocol
•Modbus interface SINEAX AM2000: Register description of Modbus/RTU communication via RS-485

6/62 Device handbook SINEAX AM2000, 173 849, 04/2015
2. Safety notes
Device may only be disposed in a professional manner !
The installation and commissioning should only be carried out by trained personnel.
Check the following points before commissioning:
– that the maximum values for all the connections are not exceeded, see "Technical data"
section,
– that the connection wires are not damaged, and that they are not live during wiring,
– that the power flow direction and the phase rotation are correct.
The instrument must be taken out of service if safe operation is no longer possible (e.g. visible
damage). In this case, all the connections must be switched off. The instrument must be
returned to the factory or to an authorized service dealer.
It is forbidden to open the housing and to make modifications to the instrument. The instrument
is not equipped with an integrated circuit breaker. During installation check that a labeled switch
is installed and that it can easily be reached by the operators.
Unauthorized repair or alteration of the unit invalidates the warranty.
3. Device overview
3.1 Brief description
The SINEAX AM2000 is a comprehensive instrument for the universal measurement and monitoring in
power systems. A full parameterization of all functions of the AM2000 is possible directly at the device.
The universal measurement system of the device may be used directly for any power system, from single
phase up to 4-wire unbalanced networks, without hardware modifications.
Using additional, optional components the opportunities of the AM2000 may be extended. You may
choose from I/O extensions or Modbus/RTU communication interface. The nameplate on the device gives
further details about the present version.
3.2 Available measurement data
The SINEAX AM2000 provides measurements in the following subcategories:
a) Instantaneous values: Present TRMS values and associated min/max values
b) Energy consumption: Power mean-values with trend and history as well as energy meters
c) Harmonics: Total harmonic distortion THD/TDD, individual harmonics and their maximum values
d) Phasor diagram: Graphical overview of all current and voltage phasors
e) Alarms: State display of monitored events

7/62 Device handbook SINEAX AM2000, 173 849, 04/2015
4. Mechanical mounting
►The AM2000 is designed for panel mounting
Please ensure that the operating temperature limits are not exceeded when
determining the place of mounting (place of measurement):
-10 ... 55°C
4.1 Panel cutout
Dimensional drawing AM2000:
See section 10
4.2 Mounting of the device
The device is suitable for panel widths up to 8mm.
a) Slide the device into the cutout from
the outside
b) From the side slide in the mounting
clamps into the intended openings and
pull them back about 2 mm
c) Tighten the fixation screws until the
device is tightly fixed with the panel
4.3 Demounting of the device
The demounting of the device may be performed only if all connected wires are out of service. Remove
all plug-in terminals and all connections of the current and voltage inputs. Pay attention to the fact, that
current transformers must be shortened before removing the current connections to the device. Then
demount the device in the opposite order of mounting (4.2).

8/62 Device handbook SINEAX AM2000, 173 849, 04/2015
5. Electrical connections
Ensure under all circumstances that the leads are free of potential
when connecting them !
5.1 General safety notes
Please observe that the data on the type plate must be adhered to !
The national provisions have to be observed in the installation and material selection of electric lines,
e.g. in Germany VDE 0100 “Conditions concerning the erection of heavy current facilities with rated
voltages below 1000 V”!
Nameplate of a device with
•Modbus/RTU interface
•4 relay outputs
•4 analog outputs
Symbol Meaning
Device may only be disposed of in a professional manner!
Double insulation, device of protection class 2
CE conformity mark. The device fulfills the requirements of the applicable EC
directives. See declaration of conformity.
Caution! General hazard point. Read the operating instructions.
General symbol: Input
General symbol: Output
CAT III
Measurement category CAT III for current / voltage inputs, power supply and relay
outputs

9/62 Device handbook SINEAX AM2000, 173 849, 04/2015
5.2 Terminal assignments of the I/O extensions
Function Option 1 Option 2 Option 3 Option 4
2 relay outputs 1.1: 51,52,53
1.2: 55,56,57
2.1: 61,62,63
2.2: 65,66,67
3.1: 41,42,43
3.2: 45,46,47
4.1: 31,32,33
4.2: 35,36,37
2 analog outputs 1.1: 51(+), 53(-)
1.2: 52(+), 53(-)
2.1: 61(+), 63(-)
2.2: 62(+), 63(-)
3.1: 41(+), 43(-)
3.2: 42(+), 43(-)
4.1: 31(+), 33(-)
4.2: 32(+), 33(-)
4 analog outputs
1.1: 51(+), 53(-)
1.2: 52(+), 53(-)
1.3: 55(+), 57(-)
1.4: 56(+), 57(-)
2.1: 61(+), 63(-)
2.2: 62(+), 63(-)
2.3: 65(+), 67(-)
2.4: 66(+), 67(-)
3.1: 41(+), 43(-)
3.2: 42(+), 43(-)
3.3: 45(+), 47(-)
3.4: 46(+), 47(-)
4.1: 31(+), 33(-)
4.2: 32(+), 33(-)
4.3: 35(+), 37(-)
4.4: 36(+), 37(-)
5.3 Possible cross sections and tightening torques
Inputs L1(2), L2(5), L3(8), N(11), I1(1-3), I2(4-6), I3(7-9), power supply (13-14)
Single wire
1 x 0,5 ... 6.0mm2or 2 x 0,5 ... 2.5mm2
Multiwire with end splices
1 x 0,5 ... 4.0mm2or 2 x 0,5 ... 2.5mm2
Tightening torque
0.5…0.6Nm resp. 4.42…5.31 lbf in
I/O's, relays, RS485 connector (A, B, C/X)
Single wire
1 x 0.5 ... 2.5mm2or 2 x 0.5 ... 1.0mm2
Multiwire with end splices
1 x 0.5 ... 2.5mm2or 2 x 0.5 ... 1.5mm2
Tightening torque
0.5…0.6Nm resp. 4.42…5.31 lbf in

10/62 Device handbook SINEAX AM2000, 173 849, 04/2015
5.4 Inputs
All voltage measurement inputs must originate at circuit breakers or fuses rated 5 Amps or
less. This does not apply to the neutral connector. You have to provide a method for
manually removing power from the device, such as a clearly labeled circuit breaker or a
fused disconnect switch.
When using voltage transformers you have to ensure that their secondary connections
never will be short-circuited.
No fuse may be connected upstream of the current measurement inputs !
When using current transformers their secondary connectors must be short-circuited
during installation and before removing the device. Never open the secondary circuit under
load.
The connection of the inputs depends on the configured system (connection type).

11/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Single-phase AC mains
L1
N
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
N
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
K
k
L
l
With current transformer
L1
N
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
9
7
IN PE
610 12 16 11 25 8
5 A
(UL listed)
v
V
u
U
With current and voltage transformer

12/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Three wire system, balanced load, current measurement via L1
L1
L2
L3
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
L2
L3
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 25 8
5 A
(UL listed)
With current transformer
L1
L2
L3
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
u
U
v
V
u
U
v
V
With current and voltage transformers
In case of current measurement via L2 or L3 connect voltages
according to the following table:
Current Terminals L1 L2 L3
L2 I1-1 I1-3 L2 L3 L1
L3 I1-1 I1-3 L3 L1 L2
By rotating the voltage connections the
measurements U12, U23 and U31 will be
assigned interchanged !

13/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Four wire system, balanced load, current measurement via L1
L1
L2
L3
N
L1 L2L3
N
I1
31
I2
4
I3
9
7
IN PE
610 12 16 11 25 8
5 A
(UL listed)
Direct connection
L1
L2
L3
N
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
9
7
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformer
L1
L2
L3
N
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
9
7
IN PE
610 12 16 11 25 8
5 A
(UL listed)
V
v
U
u
With current and voltage transformer
In case of current measurement via L2 or L3 connect voltages
according to the following table:
Current Terminals L1 N
L2 I1-1 I1-3 L2 N
L3 I1-1 I1-3 L3 N

14/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Three wire system, unbalanced load
L1
L2
L3
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
L2
L3
K
k
L
l
K
k
L
l
K
k
L
l
L1L2 L3
N
I1
31
I2
4
I3
9
7
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformers
L1
L2
L3
K
k
L
l
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current and 3 single-pole isolated
voltage transformers

15/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Three wire system, unbalanced load, Aron connection
L1
L2
L3
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
L2
L3
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformers
L1
L2
L3
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
x
u
X
U
X
U
X
U
x
u
x
u
5 A
(UL listed)
With current and 3 single-pole isolated
voltage transformers

16/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Four wire system, unbalanced load
L1
L2
L3
N
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
L2
L3
N
K
k
L
l
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformer
L1
L2
L3
N
K
k
L
l
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
x
u
X
U
X
U
X
U
x
u
x
u
5 A
(UL listed)
With current and 3 single-pole isolated
voltage transformers

17/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Four wire system, unbalanced load, Open-Y
L1
L2
L3
N
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 258
5 A
(UL listed)
Direct connection
L1
L2
L3
N
K
k
L
l
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformers
L1
L2
L3
N
K
k
L
l
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
x
u
X
U
X
U
x
u
5 A
(UL listed)
With current and 2 single-pole isolated
voltage transformers

18/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Split-phase ("two phase system"), unbalanced load
L1
L2
N
L1 L2 L3
N
I1
31
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
Direct connection
L1
L2
N
K
k
L
l
K
k
L
l
L1 L2 L3
N
I1
3
1
I2
4
I3
97
IN PE
610 12 16 11 2 5 8
5 A
(UL listed)
With current transformers

19/62 Device handbook SINEAX AM2000, 173 849, 04/2015
5.5 Power supply
A marked and easily accessible current limiting switch has to be arranged in the vicinity of
the device for turning off the power supply. Fusing should be 10 Amps or less and must be
rated for the available voltage and fault current.
5.6 Relays
When the device is switched off the relay contacts are de-energized, but dangerous
voltages may be present.
Relays are available for device versions with
corresponding I/O extensions only.
I/O extension y x
1 5
2 6
3 4
4 3
5.7 Digital inputs and outputs
For the digital inputs / outputs an external power supply of 12 / 24V DC is required.
The power supply shall not exceed 30V DC !
A digital input and two digital outputs are provided as a standard.
Usage as digital input
►Clock synchronization
►Synchronization of billing intervals in accordance with energy provider
►Meter tariff switching
Technical data
Input current < 7,0 mA
Logical ZERO - 3 up to + 5 V
Logical ONE 8 up to 30 V

20/62 Device handbook SINEAX AM2000, 173 849, 04/2015
Usage as digital output
►Alarm output
►State reporting
►Pulse output to an external counter (acc. EN62053-31)
1) Recommended if input
impedance of counter > 100 kΩ
Driving a counter mechanism
The width of the energy pulses can be selected, but
have to be adapted to the counter mechanism.
Electro mechanical meters typically need a pulse
width of 50...100ms.
Electronic meters are partly capable to detect pulses
in the kHz range. There are the types NPN (active
negative edge) and PNP (active positive edge). For
the AM2000 a PNP type is required. The pulse width
has to be at least 30ms (acc. EN62053-31). The delay
between to pulses corresponds at least to the pulse
width. The smaller the pulse width, the higher the
sensitivity to disturbances.
Driving a relay
Rated current 50 mA (60 mA max.)
Switching frequency (S0) ≤ 20 Hz
Leakage current 0,01 mA
Voltage drop < 3 V
Load capacity 400 Ω… 1 MΩ
5.8 Analog outputs
Analog outputs are available for devices with corresponding I/O extensions only. See nameplate.
Connection to an analog input card of a PLC or a
control system
The AM2000 is an isolated measurement device. The
particular outputs are not galvanically isolated. To
reduce the influence of disturbances shielded a
twisted-pair cables should be used. The shield should
be connected to earth on both opposite ends. If there
a potential differences between the ends of the cable
the shield should be earthed on one side only to
prevent from equalizing currents.
Under all circumstances consider as well appropriate
remarks in the instruction manual of the system to
connect.