Campania International Andalusia FT-120 User manual

FT
-
12
0A
ndalusia
Fountain
Professionalinstallation isrecommendedforthisfountain!
R
evised
October 15, 2019
PumpKitParts List
PK300 pump(1)
LED-LIGHT(1)
LED-TRANS (1)
#5 wingnutdrainstopper (1)
#7 wingnutdrainstopper (1)
Approx. 20”lengthof 1/2” Blacknon-kinktubing (1)**
Approx. 2” lengthof5/8”clearvinyl tubing(1) **
Approx. 2” lengthof1/2” CPVC pipe (1)
Approx42”lengthof 3/8”galvanized pipe (2)
10oztubeofsilicone (1)
Hoseclamps(1) *
Wedges(2)
*Hoseclampsmay be used asflowrestrictors
**Black non-kink tubing and clear vinyltubing havebeen preassembled
***DonotpreassembletheLEDLightandTransformer
-WINTER CARE-
Fountain bowls/topsand otherfountain components, which collectwater, should notbe left outsideinthe wintersince
any component,which fillswith waterand freezesmaycrack. Likewise, componentssuch aspedestals, which remain ina
basin, filled with water, which then freezes,may also crack orcrumble. Ideally,therefore, a fountain shouldalwaysbe
stored indoors orin a dry protected place such asa covered porch away fromthe elements. However,if a fountain mustbe
leftoutside:
(1)Remove pump, rubberstoppers, drainpipes,finials, and othersmallcomponentsforstorage indoors.Note that
stoppersordrainpipesare removed to allowdrainagein the eventwateraccumulatesin any basin.
(2)Raisefountain base fromground with wood stripssothatbase will notfreeze to the ground surface.
(3)Coverorwrapthefountainwith burlaporotherabsorbentmaterial(old blanketortowel)and then coversecurely
with plastic, making surethatwaterwillnotaccumulate inthe basin orotherfountain componentandfreeze;
(4)Check fountainperiodically toensurethatplastic issecure and waterisnotaccumulating in anyfountain
component.
-GENERALFOUNTAINTIPS-
Install fountainson a levelsurface. You will need aproperlygrounded 110-volt (AC only)GFCIprotected receptacle
nearthe fountain foryourpump. All pumpsare submersibleand mustbe completely underwaterto function properly.
Testallpumpsand adjustto fulloutputpriortoassembly. Itisnotrecommended thatfountainsbe placed directly on grass
ordirt.Position the channelopening atthe base ofeachfountain towardthe
electricaloutletto be used since the pump cord will be threadedthrough this
opening.
Check outYouTube fora “Howto” video.
Formore Campania productinformation visit www.campaniainternational.com
All of ourcaststone is proudly
FOUNTAININFORMATION:
Thisfountain holdsapproximately60 gallonofwater.
Thisfountain doesnot fit under aCampaniafountain
cover.
Compatible with#10 Refill Device and LEDKits
(Nostoppersare required tousethe refill kit orLED
kit forthisfountain.)
TOOLSREQUIRED:
Bubble Level
CaulkingGun
Hammer
PUMP INFORMATION:
OEMPF320 - 320GPH Pump
16 FTcord length

FT
-
12
0A
ndalusia
Fountain
Professionalinstallation isrecommendedforthisfountain!
R
evised
October 15, 2019
Assembleyourfountain on a levelsurface capable ofholding a minimumof2200 poundswithapproximatelya 13.5
square footfootprint.
FT-120C(1080 lbs)
56.25”L x30”Wx17.5”H
FT-120A(532 lbs)
55”L x16”Wx38”H
(2)FT-120CAP (>1 lb)
1”L x1”Wx1”H
FT-120B(37 lbs)
13”L x7.5”Wx15.25”H
1. Placethe base (FT-120C)into position where the fountain willbe installed, ensuring
thatitislevel.
2. Using a caulking gun,run a bead ofsilicone along the top ofthe basin (FT-120C)
wherethe waterfeature(FT-120A)willbe placed. Take care notto usetoo much
silicone to minimizeoozingofsilicone frombetween the pieces.
3. Placethe waterfeature (FT-120A)on top ofthe basin(FT-120C)making sure that
the PVC pipe holesare lined up between the top ofthe basinand the bottomofthe
waterfeature.
4. BE CAREFUL NOTTOPINCHFINGERS WHENLOWERING!
a. Hand holdshave beenmolded intothe water feature for easier
assembly.
5. Clean off any excess silicone with yourfingerora dryrag asquickly aspossible.
6. Using a hammer, gentlytapthe 2” length ofCPVC pipe into the PVC coupling in
the bottomofthe waterfeature (FT-120A).
a. Note:To preventbreakage, do notdo thisstep early.
7. Placethe #5 drain stopperinto the holeatthe bottomofthe bowlon the water
feature (FT-120A).
8. Drop the supportpipesintothe holesatthe top ofthe waterfeature(FT-120A).
a. Check thatthe pipeshave droppedallthe way through the waterfeature
(FT-120A)AND basin (FT-120C)beforegoing forward.
9. Insert the stone caps(FT-120CAP)intothe holesoverthe pipes.
a. Note:The capsareremovable.
10. Assemblethe pump kit
a. Using a hoseclamp, attach the 1/2"black tubing to thepump outlet.
11. Placethe pump and LEDlightin the fountainand feedthe cordsthroughthe hole
between the basin(FT-120C)and waterfeature(FT-120A).
a. Attach the LEDlighttothe transformeroutside ofthefountain.
12. Fit the otherpiece of5/8” cleartubing overthe CPVC installed into the water
feature (FT-120A)instep 6.
13. Placethe pump cover(FT-120B)overthe pumpalongthe back ofthe basin.
14. Placethe #7 drain stopperinto the holeatthe bottomfrontofthe basin.
15. PlaceLEDlightinthe frontofthe basinaiming the lightatthe waterfall.
16. Letthe fountain sit24 hoursbeforefilling itwith water.